Gfe28gskss Parts

This felt tape is used in the refrigerator to cushion and seal mating parts, helping reduce vibration/squeaks and prevent chafing or small air leaks. Replace worn or missing tape to restore a quieter, more secure fit of covers and ducts.

• Provides a soft barrier between panels, ducts, or rails to minimize vibration and squeaks
• Helps seal minor gaps to support proper airflow paths
• Replaces deteriorated, compressed, or missing original felt tape
• Common symptoms include rattling/buzzing from covers or panels, squeaking drawers, or a loose cover that won't seat correctly

• Disconnect power to the refrigerator before servicing
• Note the original tape's location; remove the old tape and any residue
• Clean and dry surfaces thoroughly; apply the new tape in the same position (peel liner if adhesive-backed)
• Do not block vents, sensors, or fastener holes when applying

This hinge-mounted refrigerator door stop limits how far the door swings open, protecting the cabinet and nearby walls from impact. Replace a cracked or missing stop to restore a controlled, factory door swing and prevent overextension.

• Mounts on the door hinge to control the door's opening range
• Helps prevent the door or handle from striking adjacent walls or cabinets
• Common symptoms: door opens past its normal range, broken/missing stop, visible wear at the hinge stop
• Often needed after an impact or when the original stop cracks from fatigue

• Disconnect power; turn off water to the door if applicable
• Support the door before loosening hinge fasteners; door removal may be required on some models
• Install the stop on the correct hinge location (right or left as required) and tighten hardware securely
• Verify door swing and clearance before fully loading shelves

This water filter cover assembly secures the refrigerator's water filter cartridge and helps direct filtered water into the dispenser/ice system, restoring proper filter seating and reducing the risk of leaks or poor water flow. What it does:

• Secures and retains the water filter cartridge in its housing
• Seals the filter area to help prevent water leaks around the filter
• Directs filtered water from the cartridge into the dispenser and ice system
• Helps restore proper filter engagement when the original cover is cracked or broken

• Turn off water supply and remove power to the appliance before servicing
• Remove the old cover and verify filter type/orientation before installing the new cover
• Push the cover into place until the filter seats and locks per the appliance design
• Re-check alignment and seals; replace damaged gaskets as needed

A #8-18 x 9/16-inch hex washer head screw used to secure panels and components in appliances. Provides a proper fit for fast, reliable fastening when replacing missing, damaged, or stripped screws. What it does:

• Secures panels, brackets, and trim to keep components aligned and stable.
• Restores proper fastening when threads are stripped, the original screw is missing, or a head is damaged.
• Helps stop rattling or loose parts caused by worn or broken fasteners.
• Fits applications requiring a #8-18 thread with a 9/16" length and hex washer head style.

• Verify thread size, head style, and length before installation.
• Use the correct hex driver or socket to avoid cam-out or head damage.
• Do not overtighten; snug until secure to avoid stripping threads or deforming parts.
• Disconnect power and follow appliance-specific safety steps.

A replacement fresh-food door handle that restores a secure grip and the finished look of the refrigerator door. Fits stainless finishes and replaces worn, cracked, or damaged handles to make daily use easier. What it does:

• Provides a sturdy grip for opening the fresh-food compartment door
• Replaces handles that are cracked, loose, or cosmetically damaged
• Restores proper alignment and ease of door operation when the original handle is broken
• Matches stainless finishes for a factory look

• Designed for direct replacement; use the factory mounting screws and brackets already on the door when present
• Turn off water/ice supply and empty door bins if they obstruct access before starting
• Handle small hardware carefully; keep screws and trim pieces together to avoid loss

This port collar is a small trim/support piece used on select refrigerators. It reinforces the port opening and helps secure the mating tube or component for proper alignment, a snug fit, and a clean, finished appearance.

• Supports and spaces the port/opening where a tube or component passes through the cabinet or liner
• Helps maintain alignment and a secure fit to minimize gaps or vibration
• Replace if the collar is cracked, warped, or missing
• Symptoms can include a loose connection at the opening, rattling, or a visible gap or misalignment

• Unplug the refrigerator; shut off the water supply if working near water lines
• Use your model's parts diagram to access the port; remove any trim, clips, or screws
• Note orientation; press or snap the new collar into place and transfer any seals if present
• Reassemble and restore power; verify proper fit and operation

Manufactured by GE, this is a compressor kit for a refrigerator. The compressor's job is to pressurize the system and warm the refrigerant while propelling it through the rest of the cooling system. The compressor is controlled by a thermostat inside the refrigerator. When the thermostat detects a high temperature, the compressor engages, helping to cool the refrigerator and preserve food.Compressors are the core of the refrigeration system. There are also subject to a great deal of wear and tear through normal cycling on and off. In addition, compressors can be damaged if they run out of oil, if contaminants enter the system, and through exposure to prolonged operation due to a faulty thermostat or low refrigerant levels. When the compressor fails, the refrigerator will no longer be able to maintain a safe temperature for food. This is a complete replacement kit.This kit is a genuine OEM part and is sold individually. It is only compatible with GE refrigerators.

8-18 hi/lo 5/8

This 8-18 x 9/16 screw is a short sheet-metal fastener used to secure panels, trim and small components on appliances. It replaces missing or stripped screws to restore proper fit and reduce noise from loose parts. What it does

• Secures appliance panels, brackets and trim to prevent movement and rattling
• Holds small components in correct alignment for reliable operation
• Replaces lost, worn or stripped screws that cause gaps or loose fittings
• Common symptom link: fixes rattling panels, loose trim, or parts that shift during use

• One 8-18 x 9/16 screw

• Use the correct 8-18 driver bit and hand or low-torque power driver to avoid stripping
• Do not overtighten; snug until secure to prevent thread damage or panel deformation
• Turn power off/unplug appliance when installing near electrical components
• Keep extra screws on hand—hardware often comes in single quantities

This is a replacement round-head 10-32 x .353 screw used to fasten appliance panels and internal components. It restores secure mounting and helps stop rattling or loose parts caused by missing or worn fasteners. What it does:

• Secures panels, brackets, or small assemblies where a 10-32 machine screw is specified
• Stops movement and vibration that can cause noise or misalignment
• Replaces missing, stripped, or corroded fasteners to restore proper fit
• Matches the original fastener size and head style for correct clearance

• One 10-32 x .353 round-head screw

• Use the matching driver (typically a Phillips or slotted driver as required by the head) and avoid over-torque to prevent stripping
• Disconnect power and follow safety procedures when accessing internal components
• If other fasteners appear damaged or corroded, inspect and replace as needed

This element holder assembly secures an oven/range heating element and keeps it positioned for even heat delivery. It restores proper element alignment to reduce arcing and prevent rubbing or uneven baking. What it does:

• Secures the bake or broil heating element to the range/oven housing
• Keeps the element properly spaced for consistent heating performance
• Helps stop element movement, rubbing, or intermittent contact that can cause arcing
• Commonly replaced when the element is loose, misaligned, or makes noise during operation

• Disconnect power to the appliance before beginning any repair
• Handle heating elements carefully—sharp edges and fragile terminals can be damaged
• Verify element alignment and secure mounting hardware; replace only as needed
• If you see damaged element terminals or insulation, replace the element

The Cover Front Panel Assembly is an OEM component for GE side-by-side refrigerators. Forming the handle and facade area of the fresh food compartment door protects inner mechanics while maintaining aesthetic integrity. Dependable operation relies on an intact front panel assembly.

Symptoms of a defective assembly include:

• Misaligned or loose-fitting facade panels detracting from appearance   
• Drafts noticeable around door perimeter compromising energy efficiency
• Poor fit inhibiting smooth door closure or opening  

Causes involve years of use compromising anchor clips through opening/closing stress, moisture exposure distorting composite materials, or impacts dulling factory sheen over time.

Replacing with this genuine GE assembly restores a factory finish look while supporting full door function. Compatible with Hotpoint, RCA, or Kenmore models seeking to preserve operation with an aesthetically pleasing front.
 

This hinge cap is the small trim piece that covers your refrigerator door hinge. Replacing a cracked or missing cap protects the hinge from dust and restores a clean, finished look to the door area.

• Covers and protects the door hinge hardware from dust and debris
• Restores a clean, factory-finished appearance
• Helps keep the hinge area clear for smooth door movement
• Replace when the original cap is cracked, loose, discolored, or missing

• Disconnect power before servicing the appliance
• Support the door to prevent movement while working near the hinge
• Remove the old cap; align and press the new cap onto the hinge until fully seated; reuse the original fastener if your model uses one
• Verify the cap is secure and does not rub as the door opens/closes

This Pex water line is the flexible inlet tubing that carries water to the refrigerator's dispenser and ice maker. It replaces worn or damaged tubing to restore reliable water flow and prevent leaks. What it does:

• Transfers water from the household supply to the refrigerator water valve, dispenser and ice maker
• Replaces cracked, pinholed or hardened tubing that can cause leaks
• Helps restore normal water flow when the dispenser or ice maker isn't filling
• Provides a flexible, corrosion-resistant connection for routine service or repair

• Turn off the refrigerator and shut off the home water supply before starting
• Drain any residual water from the line and relieve system pressure before disconnecting fittings
• Inspect and, if needed, replace any clamps, ferrules or valves shown in your service instructions; tighten fittings to OEM torque recommendations

This right-hand hinge top pin assembly supports and lets a refrigerator or freezer door pivot smoothly, restoring proper alignment and door operation. Use it to correct sagging, misaligned doors, or noisy pivoting. What it does:

• Provides the pivot point for the door's top hinge to enable smooth opening and closing.
• Restores proper door alignment to fix uneven gaps or doors that rub or stick.
• Helps eliminate grinding or squeaking noises from a worn or damaged hinge area.
• Supports the door weight to prevent further sagging or seal damage.

• Unplug the appliance or switch off power before servicing to reduce shock risk.
• Support the door when removing hinge fasteners to prevent dropping or damage.
• Use basic hand tools; follow OEM procedure for loosening/tightening hinge hardware and torque if specified by manufacturer.

This door case wiring harness connects the refrigerator door components to the main cabinet harness, restoring reliable power and signal routing for lights, dispensers, and sensors. Replaces a damaged or frayed harness to help resolve intermittent or non-working door functions. What it does:

• Transfers power and control signals between the door and cabinet wiring
• Restores operation for door-mounted lights, dispensers, and sensors affected by broken wiring
• Prevents shorts or intermittent failures caused by frayed or pinched wires
• Matches OEM routing and connector locations for a direct-replacement fit

• One door case wiring harness

• Disconnect power to the appliance before starting work to avoid shock or injury
• Handle connectors gently and route wiring per cabinet clips to avoid pinching
• Verify connector orientation and seating; secure any retained clips or screws