Gfe28hgh Parts

Vegetable bin top frame that supports and aligns the crisper/vegetable drawer while maintaining a sealed opening to help preserve produce. Replacing a worn or cracked frame restores proper drawer fit and reduces gaps that trap moisture. What it does:

• Supports and aligns the crisper/vegetable drawer for smooth insertion and removal.
• Replaces cracked, warped or broken frames that can cause drawer sagging, sticking, or poor seating.
• Helps reduce air leakage and moisture buildup that contribute to premature spoilage of produce.
• Matches original-equipment fit and function to restore correct drawer alignment and sealing.

• Unplug the refrigerator or disconnect power before starting any service.
• Remove contents and the crisper drawer before replacing the frame to avoid damage.
• Basic hand tools may be required; handle edges carefully to avoid cuts or damage to surrounding trim.

This 1/4-inch quick-connect locking clip secures water tubing in push-to-connect fittings on your refrigerator's water and ice system. It locks the tube in place to help prevent leaks and accidental disconnection at the fitting. What it does:

• Locks 1/4-inch OD tubing into compatible push-to-connect fittings
• Helps maintain a secure seal to reduce drips at water line connections
• Replaces a missing, cracked, or loose clip on filter heads, inlet valves, or inline couplers
• Symptoms include leaks at a fitting or a tube that won't stay seated

• One 1/4-inch quick-connect locking clip

• Disconnect power and shut off the water supply before servicing; dispense water to relieve pressure
• Remove the old clip; ensure the tubing end is clean and cut square
• Fully insert the tube into the fitting until it bottoms out, tug lightly to seat, then install the clip in the collet groove
• Restore water and check all connections for leaks

• Designed for fittings that use 1/4-inch OD tubing. It will not fit 5/16-inch or 3/8-inch quick-connect fittings.

This gasket seals the perimeter of the freezer door to keep cold air in and humid air out. Replacing a worn or torn gasket restores a tight seal, stabilizes temperatures, and helps reduce frost and energy waste.

• Creates a tight seal around the freezer door opening
• Helps maintain proper freezer temperature and efficiency
• Reduces frost, condensation, and warm-air leaks
• Common signs of failure: cracks or warping, door not closing flush, moisture or frost along the door edge

• Safety first: Disconnect power before servicing
• Warm the new gasket in hot water or with low heat to relax folds
• Remove the old gasket and seat the new one fully into the door channel/under retainers, starting at the corners
• Check the seal with a paper test and adjust door/retainers as needed for uniform contact

The Ice Bucket and Crusher is an OEM component for GE side-by-side refrigerators equipped with an internal ice system and ice crusher feature. Located in the freezer section, it provides filtered ice-crushing and storage abilities. Consistent icemaking depends on an intact ice-handling mechanism. 

Symptoms of a faulty bucket and crusher include:

• Gradual accumulation of uncrushed ice cubes within the storage bin  
• Drive motor straining or temporarily ceasing during heavy usage
• Partial blockage of ice chute restricting flow into glasses

Causes range from mineral contamination slowing mechanical components to wear from constant high-volume usage dulling edges or linkages over time. Regular cleaning helps but replacement maintains long-term efficiency.

Replacing with this genuine GE bucket and crusher restores optimized ice handling performance through engineered durability and precision mechanisms. Compatible replacements suit Hotpoint, RCA, or Kenmore models seeking automated, whole-home ice production and retrieval cycles without interruption.
 

This valve body assembly routes and supports the refrigerator's water flow for the dispenser and ice maker. Replacing a cracked or leaking body restores proper water delivery and helps prevent leaks at the rear of the unit.

• Directs incoming water to the dispenser and/or ice maker
• Maintains sealed connections for water lines and valve components
• Helps resolve leaks around the rear valve area
• Symptoms can include no/slow dispenser flow or an ice maker not filling

• Unplug the refrigerator and shut off the household water supply
• Relieve line pressure; place a towel or container to catch residual water
• Note tubing and wire positions; transfer to the new assembly and ensure every connection is fully seated
• Restore water and power, then check all joints for leaks while dispensing and during an ice maker fill

This roller assembly helps refrigerator drawers and baskets glide smoothly along their tracks. When the wheel or bracket wears or breaks, drawers can stick, scrape, or sit unevenly—replacing the roller restores easy, consistent movement.

• Supports and guides a drawer or basket on its track
• Restores smooth in-and-out sliding action
• Replaces a cracked, worn, or missing wheel/bracket
• Common symptoms: drawer hard to open/close, scraping noise, drawer tilts or drops

• Disconnect power and remove the affected drawer/shelf to access the roller
• Note orientation; remove retaining screw or clip and detach the old roller
• Position and secure the new roller—avoid overtightening into plastic
• Reinstall and test the drawer; clean the tracks and check for damage or misalignment

This is the hinge for the refrigerator door mullion—the folding center rail (flipper) between the doors. It lets the mullion pivot smoothly and seal the door gap, helping prevent air leaks, condensation, and poor door closure.

• Allows the mullion to fold open and closed with door movement
• Helps maintain an even, airtight center seal between doors and gaskets
• Common fix for a broken/loose flipper or a mullion that won't pivot or return
• Resolve doors not closing fully, air leaks, or condensation along the center rail

• Unplug the refrigerator before servicing
• Support the door and mullion to avoid stressing hinges and gaskets
• Note hinge orientation and screw locations during removal; reuse existing hardware
• After installation, verify smooth mullion action and a proper center seal

A replacement bracket that secures the refrigerator water-filter manifold to the cabinet, keeping the filter head stable and properly aligned so the filter seats correctly and helps reduce leaks and vibration during use. What it does:

• Secures and supports the water-filter manifold assembly to the refrigerator cabinet.
• Keeps the filter head aligned so the filter cartridge seals correctly.
• Helps prevent movement-related leaks or disconnections of the water lines.
• Replaces bent, cracked or missing brackets that can allow the filter housing to shift.

• Turn off water supply and unplug the appliance before beginning; have a towel or small container ready to catch residual water.
• Remove the filter or access panel as needed to reach the manifold; keep fasteners for reuse or replace if damaged.
• Use common hand tools (screwdriver/socket) and install bracket in the same orientation as the original; do not overtighten mounting hardware.
• After installation, restore water and power, check for leaks, and confirm the filter seats and dispenses properly.

The Mullion Striker is an OEM part for GE refrigerators responsible for securing the mullion or flipper door in place when it is closed, ensuring a tight seal and temperature inside the refrigerator.

A bad mullion striker can be caused by normal wear and tear over time, damage due to excessive force or impact, or misalignment of the mullion assembly. If you notice that the mullion door does not stay securely closed, causing a gap or allowing warm air to enter the refrigerator, it may indicate a problem with the mullion striker.

Symptoms of a bad mullion striker include:

• Difficulty in keeping the mullion door closed
• Visible gaps or improper sealing when the door is closed
• Condensation or frost buildup around the mullion area
• Unusual noises from the mullion assembly

Replace your faulty mullion striker with this genuine OEM part to restore your refrigerator. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

Cold water tank assembly stores and supplies chilled water to the refrigerator's dispenser and related water channels. Replacing a damaged reservoir helps stop leaks and restore reliable chilled water flow. What it does

• Holds chilled water for the dispenser and downstream water paths
• Routes supply and return lines through built-in inlet/outlet ports
• Common symptoms: leaking reservoir, little or no water from the dispenser, slow or inconsistent flow
• Use as a direct replacement when the existing tank is cracked, warped, or otherwise damaged

• Disconnect power and shut off the water supply before beginning service
• Drain the reservoir and place towels or a pan to catch residual water when removing the old tank
• Access may require removing interior panels or shelving; retain or inspect mounting hardware and seals for reuse

This replacement power cord harness connects the appliance's incoming mains power to its internal wiring, restoring a secure electrical path. Use it to replace damaged or worn harnesses to help resolve power loss or intermittent operation. What it does:

• Routes mains power from the inlet to the control board and internal components
• Replaces frayed, cut, or heat-damaged wiring that can cause intermittent power or complete power failure
• Restores secure connector and terminal connections to reduce arcing or loose-contact symptoms
• Maintains factory routing and strain relief when installed correctly

• Disconnect power at the breaker or unplug the appliance before starting any repair
• Replace with the same connector orientation and routing as the original harness to ensure correct fit and strain relief
• Inspect related terminals and wire insulation; if you see melted terminals or heavy corrosion,

The Heater Harness Fz W/tco is an OEM part for GE refrigerators. This essential component is responsible for preventing ice buildup and ensuring proper defrosting in the freezer compartment. This freezer heater harness with TCO defrost thermostat helps maintain the optimal temperature and humidity levels in your freezer. It is designed to melt away any ice or frost that may accumulate on the freezer coils, preventing them from obstructing airflow and affecting the cooling performance.

A bad freezer heater harness can occur due to wear and tear, electrical faults, or other factors. If you notice symptoms such as excessive ice buildup, inconsistent cooling, or frequent freezer defrosting cycles, it may be time to replace this part.

Symptoms of a bad freezer heater harness with TCO defrost thermostat include:

• Excessive ice buildup
• Inconsistent cooling
• Frequent freezer defrosting cycles

Prevent ice-related issues by replacing the faulty freezer heater harness with TCO defrost thermostat with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This clip secures the evaporator thermistor to the evaporator tubing so the control can read coil temperature accurately. Replacing a damaged or missing clip helps restore correct cooling and defrost performance by keeping the sensor firmly in place. What it does:

• Holds the evaporator thermistor tightly against the evaporator coil/tubing for accurate temperature sensing
• Supports proper cooling regulation and defrost cycle timing
• A loose or misplaced sensor may show temperature swings, long run times, or frost buildup on the evaporator
• Restores correct sensor placement after repairs or when the original clip is lost or broken

• 1 evaporator thermistor clip

• Unplug the refrigerator; interior metal edges and fins are sharp—wear cut-resistant gloves
• Remove the evaporator cover to access the sensor; note the original sensor location and orientation
• Transfer the thermistor into the new clip and attach it at the same spot so the sensor makes firm contact; do not pinch wires
• Reinstall panels, keep wiring clear of the fan, and restore power

This mounting screw secures appliance components to the chassis for a tight, rattle-free fit. Replacing a missing, stripped, or corroded fastener helps keep panels, brackets, or burner assemblies properly aligned and secure.

• Fastens designated parts to the appliance frame or mounting points
• Helps maintain proper alignment of panels, trim, brackets, or burner assemblies
• Restores hold when the original screw is worn, rusted, or lost
• Symptoms include loose or wobbly components, rattling/vibration, or visible gaps

• Disconnect power; allow all surfaces to cool. For gas units, also shut off the gas supply.
• Use the correct driver/bit; avoid cross-threading.
• If mating threads or clip/nut are damaged, repair or replace them before installing.
• Tighten until secure; do not overtighten to prevent stripping.

Replacement grille thermistor. This temperature sensor monitors air at the grille location and relays the signal to the control so cooling and defrost responses stay consistent and food stays within target temperatures.

• Senses ambient air temperature at the grille and varies resistance with temperature
• Sends data to the control to help regulate compressor/fan run time and defrost intervals
• Aids in maintaining stable refrigerator and freezer temperatures
• A failing sensor may lead to temperature swings, extended run time, or irregular defrosting

• Disconnect power before servicing
• Remove the grille/kickplate to access the sensor and its connector
• Disconnect the old sensor, install the new one, and route wiring as originally; ensure the sensor is fully seated and wires aren't pinched
• Restore power and allow up to 24 hours for temperatures to stabilize

Port Gasket forms a watertight seal around the refrigerator dispenser port to prevent leaks and moisture intrusion. Installing a fresh gasket restores proper sealing and helps stop dispenser drips and water pooling. What it does:

• Seals the dispenser/port opening to prevent water from leaking at the door area.
• Helps stop visible dripping or pooling near the dispenser and reduces moisture buildup.
• Replaces worn, cracked, flattened, or missing gaskets that allow leaks or drafts.
• Restores a proper seal so the dispenser operates without water escaping around the port.

• Disconnect power (and shut off the water supply if working near the dispenser) before beginning work.
• Remove the old gasket and thoroughly clean mating surfaces to ensure a full seal.
• Press the new gasket evenly into the port opening, making sure it seats all the way around.
• After installation, restore power/water and run a small dispense test to confirm no leaks.