Gi6drxxy00 Parts

Freezer or fridge light not working even with a new bulb? This light socket provides the electrical connection. Basic DIY repair with video guide.

Refrigerator not cooling or freezer too warm? A damaged evaporator fan blade stops cold air circulation. This replacement restores airflow. Video guide included.

This tempered glass shelf fits inside the refrigerator's fresh food compartment and provides a flat, sturdy surface for organizing food items. It rests on shelf support brackets or frame rails within the cabinet. Replace it if the glass is cracked, chipped, or shattered, which can compromise food safety and reduce usable storage space.

Forms the interior of your refrigerator's ice and water dispensing area. Replace if cracked, broken, or causing drips and frost buildup at the chute.

Covers the lower front opening of your refrigerator. Replace this grille when the original is cracked, broken, or missing to restore a finished look.

Limits refrigerator door travel to prevent overextension and cabinet damage. Replace if cracked, broken, or worn to restore controlled door movement.

This ice dispenser solenoid assembly engages the dispenser mechanism to switch between crushed and cubed ice. A worn or failed solenoid can prevent the selector from changing modes or stop ice from dispensing smoothly.

• Actuates the ice bucket/crusher selector to allow cubed or crushed ice
• Failure may cause only one ice option to work, no change between modes, or intermittent dispensing
• Can resolve loud clicking/buzzing from the dispenser area when switching options
• Helps restore proper ice dispensing performance

• Disconnect power before servicing the dispenser area
• Access is typically through the freezer door dispenser chute/ice bucket area
• Note actuator linkage orientation during removal to ensure correct reassembly
• After installation, test both crushed and cubed selections

This is a small spur gear used in the drawer glide assembly, typically on the left side of a refrigerator or freezer drawer. It meshes with the drawer track mechanism to allow smooth opening and closing. Replace this gear if the drawer is difficult to slide, feels rough or catches when pulled out, or if the original gear teeth are worn or broken.

Restore a tight, even seal between your refrigerator's doors. This vertical mullion assembly flips into place to cover the center gap, helping maintain proper temperatures and reduce condensation.

• Bridges the gap between doors to create a continuous sealing surface
• Helps keep cold air in and warm air out for consistent cooling
• Aids proper door alignment and smooth closing
• Common symptoms of a failed mullion: broken or wobbly flipper, doors not closing fully or popping open, moisture/icing at the center, warming in the fresh food section

• Disconnect power before servicing and open the doors
• With the door open, release the retaining screws or tabs and lift the old mullion off the upper and lower pivots
• Position the new assembly on the pivots, secure it, and verify the flipper moves freely and seals evenly against the opposite door
• Restore power and recheck door operation and gasket contact along the full height

This is an LED light assembly board that mounts inside the refrigerator compartment to provide interior illumination. It replaces the existing light module and connects to the refrigerator's electronic controls. Replace this part if the interior light flickers, dims, or fails to turn on when the door is opened.

Refrigerator freezer drawer glide gear that attaches to the rear shaft. Replace if broken, cracked, or missing tabs cause your basket to lean or fall off track.

This factory screw secures panels, brackets, and other components in your appliance. Replace a missing, stripped, or corroded fastener to restore a tight fit and keep parts properly aligned and rattle-free.

• Secures appliance components and panels in their mounting points
• Replaces damaged, stripped, or missing hardware
• Helps reduce rattling or vibration from loose parts

• Disconnect power; shut off water or gas supplies if applicable
• Match location with the original screw; start threads by hand to avoid cross-threading
• Tighten until snug; do not over-torque, especially into plastic or thin metal
• Reinstall any covers or panels and test for secure fit

Replace your cracked, chipped, or broken refrigerator glass shelf. This adjustable storage platform organizes items in your fridge compartment.

This slide rail allows dishwasher racks to glide smoothly in and out of the dishwasher tub for easy loading and unloading. It mounts to the side of the dishwasher interior and supports the weight of loaded dish racks. Replace this rail if your dishwasher rack is difficult to pull out, doesn't slide smoothly, or if the rack tilts or binds when moving.

The Drawer Slide Rail is an OEM part for Whirlpool refrigerators. It allows movement of the refrigerator drawer.

A bad drawer slide rail can be caused by regular use, wear and tear, or accidental damage. If you experience issues such as the drawer sticking, not sliding smoothly, or falling off the rail, it may indicate a problem with the slide rail.

Symptoms of a bad drawer slide rail include:

• Difficulty in opening or closing the refrigerator drawer
• Uneven or jerky movement of the drawer
• Drawer falling off or not staying in place

Replace your faulty drawer slide rail with this genuine OEM part to restore your refrigerator. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

Illuminates your refrigerator's ice and water dispenser area. Replace if light is dim, flickering, or out. Confirm fit with your model number.