Gldb95iaso Parts

This O-ring seals the turbidity sensor assembly to help keep water contained and the sensor functioning properly. It's a small replacement seal for maintaining a watertight sensor connection and reliable turbidity readings. What it does:

• Seals the turbidity (water clarity) sensor housing to prevent leaks into the sensor area
• Helps maintain correct sensor operation so the control can monitor wash water clarity
• Restores a proper seal after sensor removal or repair

• Always disconnect power to the appliance before starting any repair.
• Remove the sensor assembly per manufacturer instructions; replace the old O-ring with the new one, ensuring it seats evenly in the groove.
• Inspect mating surfaces for nicks, debris, or old sealant and clean before installing the new O-ring.
• Use an appliance-safe lubricant compatible with rubber O-rings; avoid petroleum-based products unless specified.

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

This kickplate (toe plate) replaces the lower front trim on compatible refrigerators to restore appearance and protect the cabinet base from scuffs and drafts. Durable sheet-metal construction keeps the front edge looking clean. What it does:

• Covers and protects the refrigerator's lower front area from kicks, scuffs and dirt.
• Restores a secure trim piece when the original is bent, dented or loose.
• Helps reduce visible gaps at the cabinet base for a neater fit.
• Improves appliance appearance after damage or during refurbishment.

• Disconnect power to the appliance or follow the manufacturer's safety guidance before beginning work.
• Remove the old kickplate by loosening the retaining screws or clips; lift out and set aside.
• Align the replacement plate, engage any clips or tabs, and reinstall screws; avoid overtightening.

This filter assembly is the water-filter housing that secures and connects the refrigerator's replaceable cartridge to the water supply, helping deliver filtered water and ice for everyday use. Fits inline with the fridge's dispenser/ice system. What it does:

• Holds and seals the replaceable water filter cartridge so water is routed through the filter media
• Enables filtered water to reach the dispenser and ice maker, improving taste and clarity
• Prevents leaks at the cartridge connection when properly installed and sealed
• Can cause no water from dispenser, reduced ice production, or leaking if damaged or worn

• Shut off the refrigerator's water supply before removing or installing the assembly
• Disconnect power or unplug the appliance when accessing internal components for safety
• Check and replace O-rings or seals as needed to ensure a watertight connection
• After installation, turn water back on and flush per filter manufacturer's instructions to clear air and loose carbon fines

no.8 - 10 , 3/8 phillips

This sump housing collects and channels defrost and condensation water to the refrigerator drain system, helping prevent interior pooling and ice buildup. Replaces a cracked or clogged drain housing to restore proper water flow. What it does:

• Guides meltwater from the evaporator area into the drain tube and pan
• Helps prevent water pooling or leaks inside the fresh food or freezer sections
• Reduces ice buildup around the evaporator or under the freezer floor when functioning properly
• Works with the refrigerator's drain tube and pan as part of the defrost drainage path

• One sump housing

• Disconnect power to the appliance before starting work
• Remove food and shelves as needed; allow ice to fully melt before removing the old housing
• Inspect and clean the drain tube and surrounding seals when replacing the housing