Your privacy choices: We and our partners use cookies for analytics and ads. Decline all turns them off.
Privacy Policy · Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replacement actuator arms for refrigerator ice and water dispensers. Includes both paddles. Needed when arms are broken, cracked, or missing.
Took water and ice panel apart and replaced actuator with new one. took about 15 minutes. very easy fix! Read more
Speed clip slides over panel edges to create captive threads for mounting screws. Replace worn, missing, or broken clips to restore secure attachment.
Replaced the water tube that went from the plastic tubing to the ice cube tray. Found that even though it was the same exact length as the original, there was only an extremely small gap from the end of the tube to a splash board. This may have been the root cause of my problems. Read more
Ice dispenser not working but ice is in the bin? The auger motor rotates the auger to feed ice through the chute. DIY-friendly repair in under an hour.
Replaced motor and new solenoid and yoke assembly, motor ran fine but Ice maker did not make Ice, water was turned on and the wire off and on latch was is the down position (on). Disconnected the water line from the Ice maker tray, ice had formed in the line while I was waiting for my parts (about 5 days), I would suggest disconnecting the water line at the feed end were your shut off valve is located and allow water to drain out of line. I had to remove Ice tray and submerge it pan of hot... Read more
Ice maker clicking or not producing ice? A worn drive gear with stripped teeth is often the cause. This 5-minute fix restores normal ice production.
Replaced the gear. Now it's making ice again. Perfect. Read more
This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.
Replace Read more
Fix water leaks in your refrigerator's ice maker or water line. This tube insert reinforces plastic tubing for leak-resistant compression fittings.
Glass insert that sits in the crisper cover frame above your produce drawers. Replace this part if your original is cracked, broken, or missing.
Replaced the glass cover. Read more
The Screw is an OEM part for Whirlpool refrigerators. This screw secures the refrigerator door hinge in place, allowing the door operates smoothly and seals properly.
Over time, screws can become loose or go missing during repairs or adjustments, which can lead to a misaligned door, compromised sealing, and increased energy consumption.
Symptoms of a bad screw include:
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
As soon as the parts arrived, installed them seamlessly. Thank you. Read more
Fix ice maker overfilling, water spillage, or no ice production. Includes cover, fill cup, bail arm, and harness. Easy 5-10 minute DIY install.
Checked the internet to see what the recommended fix was based upon my model # and the problem I was having. I eventually ended up at the appliance parts pros websites video showing how to remove the ice maker and change it out with a new one. The appliance parts pros video was extremely helpful in the repair process! When I contacted appliance parts pros via chat on their website they quickly confirmed that this part would fit my model. So I ordered the replacement ice maker and kept my... Read more
Secures the crisper cover slide for smooth, aligned operation. Replace if broken or missing to restore proper drawer function. Confirm fit with your model.
Shelving went in without a problem. Very simple. Checked the installation video anyway in case there was a trick to not breaking something. Learned that the nylon clips needed to be transferred and found one missing on another shelf, so ordered a replacement. The water valve was one I replaced some time ago but one of the solenoids was bad, confirmed with a meter (ohm reading is between 200-500; less than 200 or more than 500 is broken). Replaced it without a problem (becoming expert at... Read more
Specs: Hex head ,1/4-20 x 5/8
My 10 year old frig door was hanging down to the point it wasnt fully closing and sealing unless you picked up on it. I ordered a lower hinge bracket, upper and lower bearing, and spacer. My bracket was bent down a little due to my kids hanging on the door when looking at the bottom shelf and i discovered my bracket was held on by only two bolts when there was supposed to be three. I ordered a bolt too. I was able to remove the bottom hinge, remove door to replace upper and lower bearing and... Read more
Ice not dispensing or jamming? A worn auger can't move cubes from bin to chute. This rotating shaft restores smooth dispensing. Moderate DIY repair.
Initially I noticed the crusher drum was cracked and broken so I replaced the drum the retaining nut on the end of the auger and the circlip and washer. it worked fine for a time and then the drum began free wheeling. upon further inspection I discovered the retain nubs on the auger had worn down allowing the blade to slip down the auger body. so I replaced the auger, drum, drive blade, and drive cam. I recommend if you gave a problem with the ice dispenser you break down and inspect the entire... Read more
Connects sections of water tubing inside your refrigerator. Replace this adapter if cracked, leaking, or popping off to stop drips and water damage.
Ordered parts, watched videos and had it like new in five minutes! Read more
Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.
I ordered online to AppliancePartPros.com for the fridge door hinge and after quick delivery I spent 15 minutes to securely fit the door back on the frig. I'm sure to do business again for parts if needed. Read more
This roller assembly consists of small caster-style wheels mounted on a support ring, designed to allow a shelf, drawer, or internal component to slide smoothly inside the refrigerator or freezer compartment. It supports the weight of stored items while enabling easy access. Replace this assembly if the rollers are cracked, seized, or if the shelf or drawer no longer glides properly and feels stuck or wobbly.
This hex washer-head screw secures panels, brackets, and other components inside your appliance. Replacing a worn, stripped, or missing screw restores a tight fit, reduces vibration and rattles, and helps keep assemblies properly aligned.
A friends family had left her refrigerator out on a porch while they were remodeling the house she was supposed to move into. A wind storm blew the refrigerator off the porch and tore the door off. It wasn't dented at all, but when her son pu the door back on, it wouldn't seal. She asked for some help fixing it. I ordered replacement parts for the upper and lower hinge. The parts arrived quickly. I unscrewed the top hinge which was slightly bent. Set the door on its side and replaced the bent... Read more
Opt-Out Request Honored
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.