Gsh25jgdb Parts

Great site to DIY! Purchased fresh produce drawer railing and parts. Fixed in under 10 minutes. Thanks so much! Read more

Ordered the new shelf from Appliance Parts Pros, which was a genuine OEM part and much less expensive than the GE Store. Lifted the old shelf out, popped the new one in and it was done. two minutes. Read more

Replaced Ice maker very easy. Read more

The front wheel assembly replacement (WRXO2X12454) was straightforward and easy to do. Took maybe 30 minutes start to finish. The rear wheel assembly (wheel WRO2X10695 and axle WRO1X10604) that was more involved as the original wheel axle is actually a rivet that you have to cut out. 1. I used a vibrating multitool with a carbide blade to cut the axle out. Had to use a pair of vise grips to hold the rivet to keep it from spinning while cutting it. 2. The new axle I drilled a 2mm hole thru the... Read more

First I ordered a new ice door seal, spring, and crank, figuring the condensation in freezer and door was caused by ice door not sealing. Turns out the solenoid for the ice door was completely rusted and was the primary cause, if it had been replaced early, it would have saved the dispenser board. What then happened was the moisture in the freezer door damaged the control board rendering dispenser controls inoperative as well as the heater around the dispenser. Now the freezer door is dripping... Read more

Replaced the worn parts. Read more

Swapped it out for new tube. Take 5 minutes and zero effort. The drain tube will clog with mold. You can clean it out but the tube will clog again despite's you best efforts as the tube wall provide a great habitat. Ordered new tubes to facilitate swap-outs. Old tubes can be cleaned but will recolonize quickly. Read more

I ordered the heater unit from your website as well as a new evaporator panel gasket and thermostat. Once I removed the evaporator panel from the rear wall of the freezer side, I used a steamer machine I had to melt all the ice which had accumulated, I replaced the faulty heater unit and all is well. By-the-way, I consider your website amongst the very best and easy to use. I appreciate how well your developers and designers created the diagrams/pictures with numbered parts displayed,... Read more

I ordered the recommended front door shelf part Fz for my frig, it was shipped promptly. It was slightly too long, so I cut about a 1/4" with the saw... it fits nicely now. Read more

Very easy to replace the trays slide the broken one out, slide the new one in, no problems. Read more

Replacing the roller assembly corrected the problem. The key to replacing the roller assembly is elevating the refrigerator high enough to remove the roller assembly. (1) Raise and secure the refrigerator, (2) remove the metal bar across the bottom of the refrigerator to provide adequate access to the roller assembly (2-screws), (3) remove the roller assembly adjustment screw, (4) pry the roller pivot pin out, (5) pull the roller assembly toward the front of the refrigerator to remove, (6)... Read more

Called Appliance Repair Company , , service guy came out, told me that GE no longer makes that hinge and GE would need to recast would take 4 weeks plus and cost $ 100.00 plus installation, they never showed up. After a month, I purchased from Appliance parts Pros, found easy to read plan of door showing the hinge I needed, Bought the hinge and had it in the mail within a week, installed in 10 minutes, done, Thanks Appliance Parts Pros, my refrigerator is up and running again. Pat Read more

Replaced trim. Read more

I made the right initial move - I went to appliancepartspros.com and located the necessary parts. A video convinced me I could make the repairs myself. The correct parts were easily ordered and arrived quickly. I had no problem installing the parts using the knowledge I gained from the appliancepartspros.com video and the leak was fixed. Read more

Very easy to replace the trays slide the broken one out, slide the new one in, no problems. Read more

1) By using google to find videos on why the door wouldn't close, I found out I needed new cams, those same videos also showed how to remove and replace the door. 2) Then by googling the fridge model number and the word 'cam', I was able to find the parts. 3) Taking the door off was simple, I needed a phillips head screwdriver to remove the hinge cover, however the screws in the hinge plate were so tight, I needed a side handle socket wrench to loosen them. 4) The door itself is not hard to... Read more