Gsh25vgre Parts

Ordered the new shelf from Appliance Parts Pros, which was a genuine OEM part and much less expensive than the GE Store. Lifted the old shelf out, popped the new one in and it was done. two minutes. Read more

The front wheel assembly replacement (WRXO2X12454) was straightforward and easy to do. Took maybe 30 minutes start to finish. The rear wheel assembly (wheel WRO2X10695 and axle WRO1X10604) that was more involved as the original wheel axle is actually a rivet that you have to cut out. 1. I used a vibrating multitool with a carbide blade to cut the axle out. Had to use a pair of vise grips to hold the rivet to keep it from spinning while cutting it. 2. The new axle I drilled a 2mm hole thru the... Read more

Replaced Ice maker very easy. Read more

Replaced both upper and lower cam risers. Read more

Swapped it out for new tube. Take 5 minutes and zero effort. The drain tube will clog with mold. You can clean it out but the tube will clog again despite's you best efforts as the tube wall provide a great habitat. Ordered new tubes to facilitate swap-outs. Old tubes can be cleaned but will recolonize quickly. Read more

First I ordered a new ice door seal, spring, and crank, figuring the condensation in freezer and door was caused by ice door not sealing. Turns out the solenoid for the ice door was completely rusted and was the primary cause, if it had been replaced early, it would have saved the dispenser board. What then happened was the moisture in the freezer door damaged the control board rendering dispenser controls inoperative as well as the heater around the dispenser. Now the freezer door is dripping... Read more

I ordered the heater unit from your website as well as a new evaporator panel gasket and thermostat. Once I removed the evaporator panel from the rear wall of the freezer side, I used a steamer machine I had to melt all the ice which had accumulated, I replaced the faulty heater unit and all is well. By-the-way, I consider your website amongst the very best and easy to use. I appreciate how well your developers and designers created the diagrams/pictures with numbered parts displayed,... Read more

Fridge was making clicking noise and not cooling. Ice dispenser wasn’t working either. Research lead me to believe main board was out. YouTube video said to also replace compressor start relay and overload as well. Replaced all 3 parts in 15 minutes and back up and running. Read more

Replaced shelves Read more

Very easy to replace the trays slide the broken one out, slide the new one in, no problems. Read more

Replacing the roller assembly corrected the problem. The key to replacing the roller assembly is elevating the refrigerator high enough to remove the roller assembly. (1) Raise and secure the refrigerator, (2) remove the metal bar across the bottom of the refrigerator to provide adequate access to the roller assembly (2-screws), (3) remove the roller assembly adjustment screw, (4) pry the roller pivot pin out, (5) pull the roller assembly toward the front of the refrigerator to remove, (6)... Read more

New solenoid Read more

I made the right initial move - I went to appliancepartspros.com and located the necessary parts. A video convinced me I could make the repairs myself. The correct parts were easily ordered and arrived quickly. I had no problem installing the parts using the knowledge I gained from the appliancepartspros.com video and the leak was fixed. Read more

I had 2 parts that were cracked, so after changing the cracked parts as well as the dispenser switch, it was back to working normally. Simple to make the needed repairs and the videos provided on your website really helped in being prepared. Read more

Replaced motor and solenoid cube along with dispenser auger. Simply watched video on repair and installation and really had no problem. My refrigerator is so old that one of the holes in the motor did not align properly. Had to drill another hole to mount the motor to the housing, took ten minutes. The ice auger took the longest as I was afraid of breaking the plastic housing trying to get the tabs to release. Had to watch the video twice to make sure I got the blades back in the right order.... Read more

1) By using google to find videos on why the door wouldn't close, I found out I needed new cams, those same videos also showed how to remove and replace the door. 2) Then by googling the fridge model number and the word 'cam', I was able to find the parts. 3) Taking the door off was simple, I needed a phillips head screwdriver to remove the hinge cover, however the screws in the hinge plate were so tight, I needed a side handle socket wrench to loosen them. 4) The door itself is not hard to... Read more