Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Seals the front edge of your refrigerator's crisper or pantry drawer pan cover to prevent cold air loss. Replace if worn, cracked, or not sealing properly.
First I ordered a new ice door seal, spring, and crank, figuring the condensation in freezer and door was caused by ice door not sealing. Turns out the solenoid for the ice door was completely rusted and was the primary cause, if it had been replaced early, it would have saved the dispenser board. What then happened was the moisture in the freezer door damaged the control board rendering dispenser controls inoperative as well as the heater around the dispenser. Now the freezer door is dripping... Read more
The Door Handle is an OEM part for GE refrigerators. This part provides a secure and comfortable grip for opening and closing the refrigerator door.
Causes of a bad door handle can include regular wear and tear, accidental impact, or repeated use, which can lead to cracks, breaks, or loosening of the handle.
Symptoms of a bad door handle include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Replaced with new handles Read more
Clear lens covering the lower refrigerator lamp. Replace if cracked, yellowed, or missing to restore even lighting. Confirm fit with your model number.
Just enter the appliance model and the all the parts are pictured! Really easy! Read more
Supplies electrical power from wall outlet to refrigerator. Replace this cord if cut, frayed, overheated, or damaged to restore safe electrical connection.
Spliced new and old power cord near the connections in the fridge and connected them. Didn't mess with the factory harnesses or connections inside actual fridge. Read more
Color: white. Measures about 18 inches wide by 4 inches high by 8 inches deep.
Mounting screw fastens panels, brackets, and trim in refrigerators, dishwashers, and ranges. Replace missing, stripped, or rusty screws to secure parts.
The auger gearbox shaft had a spot that was stripped of threads which prevented the auger drive from spinning the ice down the chute. I replaced the auger motor/gearbox assembly, the auger drive as it had to be cut off the shaft, and the 3 mount bolts that hold it all in place. Whole job took 30 minutes from start to finish which included cutting off the drive bracket. Read more
Size: 10-32 GXTT FLP.595 S
Great site to DIY! Purchased fresh produce drawer railing and parts. Fixed in under 10 minutes. Thanks so much! Read more
Internal water reservoir with attached tubing that stores and delivers chilled water to the dispenser. Replace if cracked, leaking, or damaged.
Installing the tank went quickly. Removed the water filter from the upper compartment to stop water flow to the tank. Had to remove the two lower drawers (they tilt out of their sliding frames). There is a glass shelf that should be pulled out - it slides out via two notches in the front frame. The water tank is behind a white metal cover held by 4 screws. Keep track of all of the parts including the lip seals from the shelf. I used two Watts 5/15x5/16 couplers from Lowes for the connections.... Read more
Replace a cracked, discolored, or broken lower tail handle trim piece on your refrigerator door. Attaches to the exterior door for a complete look.
Ice maker not filling or water spilling? This fill cup directs water into the ice maker mold for proper ice production. Simple clip-on install.
Went online to appliance pro, found my model and the ice maker part number. The process was very easily. The order process was also very simple and the part was delivered promptly with installation instructions. Read more
Secures the evaporator fan assembly behind the rear freezer panel. Replace if cracked, rusted, or missing to restore proper fan mounting and clearance.
The problem was most likely the evaporator fan motor but it could have been a bad blade, loose parts or bad motor mounts. Hard to tell without taking everything apart and inspecting. Since fridge was 17 years old I decided to order the entire evaporator fan assembly as shown in the parts diagram including fan blade, motor brackets, motor, motor mounts, screws, etc. Getting to the assembly involved removing the ice maker unit plus the entire rear inside of the freezer section. Parts cost around... Read more
Glass insert for refrigerator pan cover, forming the flat shelf above crisper drawers. Replace cracked, broken, or missing glass to restore a stable surface.
I "Binged" the refrigerator model number and Appliance Parts Pros website was one of the options to click on, so I did. Found what I needed. The diagram of the refrigerator helped too. Read more
White
Replaced dispenser kit and auger. Repair videos were a great help and resolved potential problems that I usually solved by trial and error. Thanks, Appliance Part Pros! Read more
The R134 Drier is an OEM part for GE refrigerators. This component plays a critical role in the refrigeration system by removing moisture and contaminants from the refrigerant, ensuring efficient cooling and preventing damage to other parts of the system. It helps maintain the purity and effectiveness of the refrigerant as it cycles through the system.
You should replace the R134 drier if it becomes clogged or damaged. Common causes of a bad drier include wear and tear over time, exposure to moisture, or contamination from other failing components in the refrigeration system.
Symptoms of a bad R134 drier include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Secures the condenser fan motor in position. Replace this bracket if cracked, bent, or causing excessive vibration to restore stable mounting.
Includes 12 retainer rings.
I ordered a replacement auger from AppliancePartsPros.com. Upon receipt of the new auger, I watched the repair video and took the ice crusher apart. I found several other parts that needed to be replaced as well. Once All the parts were received, I again watched the video. The video was not specific enough to show how to reassemble the ice crusher blades and the two types of washers. I found another video on YouTube that walked me through specific details of assembly and everything went... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.