Gss25gshss Parts

This bottom hinge pin supports and serves as the pivot for the refrigerator door. An accurate, tight-fitting hinge pin helps the door swing smoothly and seal properly to maintain temperature and reduce wear.

• Serves as the lower pivot point for the door on the bottom hinge
• Helps keep the door aligned for proper closing and gasket contact
• Replacing a worn pin can improve door movement and reduce stress on the hinge

• Unplug the appliance before servicing
• Support the door to relieve weight from the hinge before removing hardware
• Transfer any spacers/shims in their original order to maintain alignment
• Tighten fasteners securely and check door swing and seal after installation

This ice maker stripper is the front comb that helps release cubes from the ejector during harvest. It guides ice cleanly into the bin to reduce jams and keep ice production running smoothly. What it does

• Strips ice cubes off the ejector fingers as the ice maker cycles
• Directs cubes into the bucket, helping prevent jams and cube bridging
• Wear, cracks, or warping can cause cubes to stick, spill, or clump
• Symptoms include cubes piling at the front, clicking during harvest, or reduced/no ice

• 1 ice maker stripper

• Disconnect power and shut off water before servicing
• Remove the ice bin and access the ice maker front (remove cover if present)
• Release the old stripper (tabs/screws), align the new stripper with the ejector fingers, and seat it fully
• Reinstall cover and bin; restore power and allow a full cycle to verify operation

This overload/PTCR combination is the refrigerator compressor's start device. It briefly powers the start winding and protects against overheating, helping the compressor start reliably and cycle safely so your refrigerator can maintain proper temperatures.

• Provides momentary start assistance via a PTCR solid-state relay, then opens automatically
• Protects the compressor by opening the circuit if overheating or excessive current is detected
• Symptoms of a faulty device may include no cooling, compressor clicking or humming without starting, or starting then shutting off after a few seconds
• Visible heat damage or discoloration on the device or compressor terminals can indicate failure

• Disconnect power before servicing; access the compressor compartment from the rear
• Note/photograph wiring and terminal orientation; transfer wires and any run-capacitor lead to the same positions on the new device
• Push the device fully onto the compressor pins; ensure a snug fit and proper seating
• Capacitors can retain a charge; discharge and handle per manufacturer instructions

This air diverter is a duct component that directs and balances airflow inside the refrigerator. Replacing a cracked or missing diverter helps restore proper cooling performance and reduce frost or condensation around air passages.

• Guides cold air from the evaporator through the intended duct path
• Helps maintain even temperatures between compartments
• Improves airflow seal and direction to reduce warm-air bypass
• Common symptoms: uneven cooling, weak airflow, frost/condensation near ducts, or visible damage to the diverter

• Disconnect power before servicing
• Remove shelves/drawers and the interior panel to access the diverter per your model's service information
• Note orientation and transfer any reusable screws/clips
• Do not overtighten fasteners into plastic; confirm unobstructed airflow before restoring power

This electronic board powers and controls the light at the refrigerator's water/ice dispenser. Replacing it restores reliable illumination and proper on/off operation so you can clearly see the dispenser area during everyday use.

• Supplies regulated power to the dispenser light circuit for consistent brightness
• Responds to dispenser/control inputs to turn the light on and off
• A failing board can cause flickering or dim lighting
• Common symptoms include no dispenser light, intermittent light, or a light that stays on

• Disconnect power to the refrigerator before servicing
• Access the board behind the dispenser panel/escutcheon; remove trim carefully to avoid damage
• Handle the board by the edges and avoid static discharge; ensure connectors are fully seated

This manufacturer-specified screw fastens appliance panels, brackets, and internal components in place. Replace a missing or stripped fastener to restore a tight, rattle-free fit and reliable support at the original mounting points.

• Provides the correct fastener for securing covers, brackets, and assemblies
• Replaces lost, rusted, or damaged screws
• Helps resolve loose or vibrating panels and trim
• Maintains alignment of components and hardware

• Unplug the appliance; shut off water if working near supply lines
• Match the new screw to the original location; verify length and thread
• Start threading by hand to avoid cross-threading; tighten snugly without overtightening
• Keep removed hardware organized for reassembly

Includes 12 retainer rings.

This hex-head screw secures refrigerator components where a 12-24 x 7/8 in fastener is specified. Replacing a missing, stripped, or rusted screw restores a tight, reliable fit for brackets, panels, and assemblies and helps eliminate vibration and rattles.

• Fastens panels, brackets, and other assemblies in the refrigerator at locations calling for this size hardware
• Replaces worn, stripped, or missing screws to restore secure mounting
• Helps correct loose or misaligned components and reduce vibration noise
• OEM size: 12-24 thread, 7/8 in length; hex head

• Disconnect power and, if applicable, shut off the water supply before service
• Match the screw to the original location; replace one at a time to maintain alignment
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use an appropriate nut driver or socket that fits the hex head

This light shield is the protective lens that covers the interior lamp in your refrigerator, diffusing glare and shielding the bulb from bumps. Replace a cracked or missing cover to restore clean, even illumination.

• Covers and protects the interior light assembly from impact
• Diffuses light for softer, more even brightness inside the compartment
• Helps prevent food and hands from contacting the bulb/LED area
• Common signs of failure: cracked or yellowed lens, broken tabs, cover won't stay in place, missing shield

• Disconnect power to the refrigerator before servicing
• Release the existing shield's retaining tabs or screws; align and snap/screw the new shield into place
• Handle carefully to avoid breaking tabs; allow cold plastic to warm to room temperature before installation
• Use the bulb type and wattage specified by the manufacturer to prevent heat damage

This cable clamp secures refrigerator wiring to the cabinet, keeping harnesses organized and protected. Replacing a missing or damaged clamp helps prevent chafing and vibration noise while maintaining proper clearance from fans and other moving components.

• Anchors wire harnesses in their designed routing
• Helps prevent insulation wear from rubbing or vibration
• Keeps wires clear of sharp edges and moving parts
• Common signs it's needed: missing/broken clamp, loose or dangling wires, or new rattling/buzzing noises

• Disconnect power before servicing
• Access the clamp location and note original wire routing
• Position the clamp and secure with the existing fastener; do not overtighten
• Ensure wires aren't pinched and have clearance from the fan/compressor before restoring power

Specs: 8-18 AB IHW 5/8 S

This capacitor sleeve kit insulates and protects the refrigerator's capacitor. Replacing a cracked or missing sleeve helps prevent chafing or contact with metal surfaces and wiring, supporting safe, reliable operation of the capacitor and nearby components.

• Provides electrical insulation to help prevent shorts if the capacitor contacts metal surfaces
• Adds abrasion protection and cushions the capacitor against vibration
• Restores proper fit/routing when the original sleeve is brittle, melted, or missing
• Common indications include exposed capacitor body or leads and visible rubbing marks on the old sleeve

• Disconnect power before servicing; wear gloves and eye protection
• Discharge the capacitor per service procedures before handling
• Note factory orientation/routing; slide the sleeve over the capacitor and position to clear sharp edges
• Re-secure the capacitor in its bracket/harness and verify clearance before restoring power

This 10-18 Hi/Lo hex-washer screw is a direct-use replacement fastener for appliance panels, brackets and components. It restores secure mounting and helps stop loose trim, rattling or parts that shift during use. What it does:

• Secures panels, trim pieces, mounting brackets and similar components that use a 10-18 thread with a hex-washer head
• Restores proper fit where screws are missing, stripped, or corroded
• Helps eliminate rattling, vibration noise, and misaligned parts caused by loose fasteners
• Matches OEM head and thread style for a correct mechanical fit in specified locations

• Turn power or gas to the appliance off before working on electrical or gas-equipped units; unplug when applicable
• Use the correct sized hex driver or socket to avoid rounding the head
• Tighten until snug—do not overtighten to avoid stripping threads or damaging thin sheet metal
• If replacing multiple fasteners in a load-bearing area, replace all to ensure even fit and alignment

This condenser fan mounting bracket secures the condenser fan motor and blade in the correct position to move air across the coils. Replacing a cracked or bent bracket restores stable mounting, reduces vibration, and helps maintain proper condenser airflow.

• Holds the condenser fan motor/blade assembly in alignment for proper airflow through the condenser
• Maintains clearance to prevent the fan blade from rubbing or contacting nearby components
• Helps reduce rattling, vibration, or scraping noises from the rear of the refrigerator
• Damage or misalignment can contribute to restricted condenser airflow and warmer temperatures

• Disconnect power and pull the refrigerator away from the wall to access the rear service area
• Remove the rear lower access panel; note wiring and hardware locations
• Support the fan motor/blade while removing the old bracket; transfer motor, blade, grommets, and screws to the new bracket
• The fan spins freely with proper clearance and correct airflow direction before reassembly

This light shield protects and directs the interior lamp in the refrigerator fresh-food compartment, keeping the bulb covered and preventing direct contact while improving light distribution for easier viewing. What it does:

• Covers the interior lamp to prevent bare-bulb contact and protect food from accidental breakage
• Helps diffuse and direct light for more even illumination inside the fresh-food compartment
• Replaces cracked, yellowed, or missing shields that cause glare or reduced light output
• Fits behind the fresh-food compartment light assembly to maintain proper lamp placement

• Disconnect power to the refrigerator before servicing to avoid electrical shock
• Remove the existing shield carefully; avoid forcing plastic clips to prevent breakage
• Align tabs/clips and snap the replacement shield into place until fully seated

This SCR is a solid-state switching module that controls on/off power flow in select appliance circuits. Replacing a failed SCR helps stop intermittent operation and restores reliable switching for affected motors or heating elements. What it does:

• Regulates electrical switching in the control circuit to turn motors or heaters on and off.
• Used where a solid-state switch is required for smooth, repeatable control.
• Symptoms of a failing SCR: appliance won't start, runs intermittently, hums without operating, or a controlled circuit does not respond.
• Restores proper switching when the original SCR is shorted, open, or erratic.

• Disconnect power to the appliance before beginning service; follow lockout/tagout procedures.
• Handle as an electronic component—avoid static discharge and protect the spade terminals from bending or contamination.
• Ensure correct orientation and secure mounting; reconnect wiring exactly as shown on the appliance wiring diagram.