Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Black plastic funnel extension attaches to the front of your refrigerator's ice dispenser. Replace if cracked, broken, or missing to reduce splashing.
Me and my husband fixed it. Thanks for the help. Read more
Right side
Replaced the support bracket for the ice bucket. Replaced the auger motor for the ice dispenser and installed the new coupler for the microwave tray to spin. Everything works great now! Read more
Replacement mounting screw for refrigerator panels, brackets, door handles, and trim. Needed when original hardware is missing, stripped, or corroded.
Black bottom door hinge and pin assembly for side-by-side refrigerators. Replace this load-bearing pivot component if cracked, broken, or worn out.
I replaced the lever asm. and spring Read more
Size: 10-32 GXTT FLP.595 S
Great site to DIY! Purchased fresh produce drawer railing and parts. Fixed in under 10 minutes. Thanks so much! Read more
Mounting screw fastens panels, brackets, and trim in refrigerators, dishwashers, and ranges. Replace missing, stripped, or rusty screws to secure parts.
Replaced the water tank. Followed the video instruction provided by Appliance Parts Pros. Very good instruction. Read more
Secures the evaporator fan shroud to the rear compartment frame. Replace if rusted, cracked, or broken to properly support the fan assembly and alignment.
I replaced the Evaporator Fan Motor the brackets were rusty so I ordered them. Read more
Foam insulation wraps around your refrigerator's water reservoir. Replace if torn, crushed, missing, or compressed to prevent tank sweating and condensation.
Our refrigerator takes care of my wife and I, along with our children when they visit, and the grand kids. Over the years, it's seen its fair share of wear and tear. Thankfully, nothing major has happened that hasn't been able to be repaired right here in the home, and by me. Our refrigerator is a GE side-by-side with an ice maker/water dispenser, and has held up well. I've ordered parts for it from AppliancePartsPros.com for all of its repairs, and while GE/Frigidaire have been changing out a... Read more
This is a refrigerator ice and water dispenser drip tray located on the freezer door. Color: White. It measures about 8 inches wide by 4 inches deep. For black order WR17X11655.
Ordered the new interface display - this must be the easiest refrigerator repair possible. My version popped right off without even a screw (some models have a screw). There are 3 different sizes of connector to disconnect and hook up to the new board - so you really can't mess that up. Read more
Directs airflow from evaporator through the fresh food compartment. Replace if cracked, broken, or missing to restore proper air distribution.
My husband ordered and replaced the water tank inside the refrigerator in the back. Read more
Front mounting grommet for refrigerator ice makers. Secures ice maker assembly to freezer wall. Replace if cracked, missing, or worn to restore stability.
Replaced the housing the water filter screws into. Water works fine now. Read more
White
Replaced dispenser kit and auger. Repair videos were a great help and resolved potential problems that I usually solved by trial and error. Thanks, Appliance Part Pros! Read more
Secures the evaporator fan assembly behind the rear freezer panel. Replace if cracked, rusted, or missing to restore proper fan mounting and clearance.
The problem was most likely the evaporator fan motor but it could have been a bad blade, loose parts or bad motor mounts. Hard to tell without taking everything apart and inspecting. Since fridge was 17 years old I decided to order the entire evaporator fan assembly as shown in the parts diagram including fan blade, motor brackets, motor, motor mounts, screws, etc. Getting to the assembly involved removing the ice maker unit plus the entire rear inside of the freezer section. Parts cost around... Read more
Bottom hinge that supports the refrigerator door weight and serves as the pivot point. Replace if worn, cracked, or causing door misalignment and sagging.
Replaced the hinges and all parts pertaining to hinges on the refrigerator door. Total cost was approx. $83 and it took 1 hour this morning (Saturday). Now the door is closing tightly. The refrigerator is 10 years old. GE brand. Read more
Secures the condenser fan motor in position. Replace this bracket if cracked, bent, or causing excessive vibration to restore stable mounting.
The R134 Drier is an OEM part for GE refrigerators. This component plays a critical role in the refrigeration system by removing moisture and contaminants from the refrigerant, ensuring efficient cooling and preventing damage to other parts of the system. It helps maintain the purity and effectiveness of the refrigerant as it cycles through the system.
You should replace the R134 drier if it becomes clogged or damaged. Common causes of a bad drier include wear and tear over time, exposure to moisture, or contamination from other failing components in the refrigeration system.
Symptoms of a bad R134 drier include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.