Gss25wgta Parts

For the same part in white, purchase WR02X13424.

This rear gasket cover helps seal and protect the rear edge of a refrigerator cover or panel, maintaining a proper barrier to keep cold air where it belongs and prevent moisture or debris intrusion.

• Seals the rear edge of the cover to reduce air leaks
• Helps maintain stable internal temperatures
• Can address issues like warm spots, excess frost, or condensation around the rear cover area
• Replaces a cracked, deformed, or missing rear gasket cover

• Unplug the refrigerator before servicing
• Remove any shelves, drawers, or panels blocking access to the rear cover
• Carefully release retaining tabs/screws, transfer the gasket cover, and seat evenly
• Verify the cover is fully engaged and sealing before restoring power

This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.

• Converts the solenoid's electrical action into mechanical movement for the dispenser ice chute door
• Helps maintain a proper seal to limit frost and moisture around the dispenser
• Typical symptoms: ice won't dispense; chute door won't open/close; frost/ice buildup at the chute; loud buzzing or clicking from the dispenser area
• Wear or sticking of the armature/spring can hinder movement and affect dispenser operation

• Unplug the refrigerator and shut off water to the dispenser before servicing
• Access the dispenser mechanism in the door; remove trim/control panel per your model's service information
• Note the orientation of the armature, spring, and linkage; transfer components one-for-one to the new kit and secure hardware
• Verify the solenoid plunger moves freely, reassemble, restore power, and test dispenser operation

This shelf support is the small rear rail clip that secures a refrigerator shelf or drawer rail in place. A worn or broken support can let the shelf tilt or drop, making storage unstable.

• Holds the rear of the shelf or rail securely to the cabinet wall
• Helps correct issues like a sagging, tilting, or loose shelf
• Replaces cracked, missing, or deformed supports causing poor fit
• Restores proper alignment so bins and shelves slide/seat correctly

• Unplug refrigerator before service
• Remove the shelf/bin to access the support
• Depress locking tabs and slide the old support out; snap the new one into the cabinet slot
• Ensure it's fully seated before reinstalling the shelf

This refrigerator lamp socket holds an E12-base appliance bulb and provides the electrical connection for the light fixture. Replace it when the light won't turn on or flickers despite a known-good bulb and functioning door switch.

• Secures an E12 (candelabra) bulb and supplies power to it
• Works with the door/light switch to illuminate the compartment or dispenser area
• Typical failures include heat damage, cracking, or internal contact wear
• Symptoms: no light, intermittent flicker, or a bulb that won't seat firmly

• Disconnect power to the refrigerator before servicing
• Remove any lens/cover, note wire placement, and install the new socket in the original orientation
• Use an E12-base appliance bulb with the wattage specified on your model's rating label
• Restore power and verify operation with the door switch

Water line from water valve up to icemaker fill tube.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

The Freezer Light Cover is an OEM replacement part for GE refrigerators designed to protect the light bulb in the freezer compartment from any potential damage or breaks. It helps maintain a safe and well-lit freezer environment, making it easier to locate and retrieve items.

A bad freezer light shield cover can occur due to regular wear and tear or accidental damage. If you notice symptoms such as a flickering or dim freezer light, or if the light bulb is exposed and vulnerable, it may indicate a need to replace this part.

Symptoms of a bad freezer light cover include:

• Flickering or dim freezer light
• Exposed or broken light bulb
• Insufficient lighting 

Restore lighting in your freezer by replacing the faulty freezer light cover with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This ice bucket stores the ice your refrigerator's icemaker produces and keeps it organized and ready to use. Replace a cracked or missing bin to restore proper ice storage and help prevent spills, jams, and contamination.

• Collects and stores ice cubes produced by the icemaker
• Positions under the icemaker so cubes drop cleanly into the bin
• Slides in/out for easy access and smooth operation
• Common symptoms: cracked or warped bucket, ice spilling or jamming, difficulty seating the bin, plastic fragments in ice

• Unplug the refrigerator and switch the icemaker off before servicing
• Remove the old bucket and empty any ice; transfer any reusable parts from the original if applicable
• Align and fully seat the new bucket on the guides/tabs
• Restore power and turn the icemaker back on; allow time to make ice

This is the top hinge pin for a refrigerator door. It serves as the pivot point for the door at the upper hinge, helping the door swing smoothly and stay aligned so it seals properly.

• Provides the upper pivot for the door at the hinge
• Worn or bent pins can cause sagging, squeaking, or poor door closure
• May help resolve doors that don't seal, bind, or drop
• Replacing a damaged pin can improve door alignment and operation

• Unplug the refrigerator before servicing
• Support the door while removing the upper hinge
• Keep track of any spacers/washers and reinstall in the same order
• Tighten hinge fasteners and check door alignment and seal after installation

This hinge top pin is the pivot stud for the freezer door's upper hinge. Replace a bent or worn pin to restore smooth door swing, proper alignment, and a reliable gasket seal that helps maintain interior temperatures. What it does:

• Provides the upper pivot point for the freezer door
• Helps keep the door aligned so it closes and seals properly
• Replaces a bent, worn, or broken pin causing wobble, sagging, rubbing, or poor closing
• Helps prevent air leaks that can lead to frost or temperature fluctuations

• 1 top hinge pin

• Unplug the refrigerator and support the door before servicing hinges
• Remove the top hinge cover and screws; lift the door off the lower hinge
• Replace the pin in the hinge, transferring any spacers/washers as found
• Reinstall and align the door for even gaps; verify gasket seal before restoring power

This base grille mounts across the lower front of the refrigerator, covering and protecting the condenser area and leveling components while guiding airflow. Replacing a damaged or missing grille restores a clean appearance and the intended front-vent path.

• Covers the lower opening and helps keep debris away from condenser components
• Directs airflow through the front vents as designed
• Provides a finished, clean look at the toe-kick
• Helps prevent rattling when secured properly
• Common symptoms: cracked or scuffed grille, broken tabs, won't stay attached, missing piece

• Disconnect power and wear gloves to avoid sharp edges
• Open doors slightly to clear the grille ends
• Remove any screws or release spring clips and retain existing hardware
• Align tabs and snap/secure the new grille; ensure vents remain unobstructed

This replacement screw fastens refrigerator components securely, restoring a tight, rattle-free fit when original hardware is missing, stripped, or corroded. Use it to secure panels, brackets, or trim and keep parts properly aligned.

• Secures panels, brackets, covers, or trim in place
• Helps maintain correct alignment of components and hardware
• Reduces vibration and rattling caused by loose or missing screws
• Replaces lost, rusted, or stripped screws

• Unplug the refrigerator and turn off water supply if working near water components
• Match thread and length to the removed fastener; hand-start threads to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin sheet metal
• Keep track of any spacers or washers reused from the original assembly

This replacement bottom door hinge and pin assembly fits refrigerators. The lower hinge supports the door's weight and provides the pivot point, restoring smooth swing and proper alignment for a reliable close and consistent gasket seal.

• Serves as the door's lower pivot and load-bearing support
• Maintains alignment so the gasket seals correctly
• Restores smooth opening and closing after hinge/pin wear
• Common symptoms: door sagging or dragging, popping/squeaking at the hinge, gaps or poor sealing, door not staying closed

• Disconnect power and remove items from the door before servicing
• Support the door, remove bottom hinge fasteners, and lift the door off
• Position the new hinge and transfer any spacers/shims as found
• Reinstall the door, tighten hardware, and verify alignment and gasket seal

This is a grommet and it is intended for use on refrigerators and freezers. This is a genuine replacement part made by General Electric. A new grommet might be needed if the current one is visibly worn out or damaged in any way. If there are noises from vibration coming from the lower back area of the fridge there might be need for a new grommet. This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with refrigerators and freezers, or units with a compressor and is made by General Electric.