Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Washer won't spin or agitate? This drive motor and inverter assembly controls drum rotation during wash and spin cycles. Moderate DIY repair.
Replaced control board and motor inverter assembly. The hardest part was reinstalling the washer belt . Their is a tool but hopefully I will never have to do this again. Read more
Seals the outer tub opening to prevent water leaks during wash cycles. Replace if leaking from top or gasket is damaged to restore clean performance.
My friend fixed it Read more
Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.
The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job. Read more
These mounting screws secure various internal components within your washing machine. They hold parts like panels, brackets, and mechanisms in their proper positions during wash cycles. Replace if screws are missing, stripped, or causing rattling noises during operation.
I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more
This locking clip secures a mating part—often a control knob—onto its shaft on select laundry appliances. Replacing a worn or missing clip restores a tight fit so controls stay in place and operate as intended during use.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
Plastic housing that secures the drain solenoid to the pump assembly. Replace if cracked, broken, or missing to properly position the solenoid mechanism.
Viewed you video on Youtube.com and saw how easy it was to change out the triple water valve. Job completed and working like a charm now. Read more
Double-style bushing supports the washer lid hinge pin. Replace worn or cracked bushings to restore smooth, quiet lid operation and proper alignment.
Not hard when you have videos and a mechanical background....piece of cake.... Read more
Adjustable leveling leg threads into washer base to stabilize cabinet and reduce vibration. Replace if cracked, broken, or missing for proper support.
Replace the Washer tub Dampening straps helped to reduce the vibration noise.The Video was great too. Read more
Replaces a cracked or leaking wash tub to restore water containment and drum support. Fixes leaks, rubbing noises, and vibration. Confirm fit by model.
I ordered a new mode selector and new tub bearing. Upon disassembly, I noticed that the plastic outer tub had actually heated up around the tub bearing and tub seal area, such that the new tub seal did not fit tightly. I ordered a replacement outer tub, and reassembled all the new parts. During assembly, I installed the new tub seal upside down, but recognized it while re-watching the how-to video. I pulled the assembly back off and flipped the seal over, then reassembled it again. I also put... Read more
Cushions where the washer lid meets the top panel to soften closure and protect the finish. Replace worn, cracked, or missing bumpers to reduce noise.
The problem was most likely the evaporator fan motor but it could have been a bad blade, loose parts or bad motor mounts. Hard to tell without taking everything apart and inspecting. Since fridge was 17 years old I decided to order the entire evaporator fan assembly as shown in the parts diagram including fan blade, motor brackets, motor, motor mounts, screws, etc. Getting to the assembly involved removing the ice maker unit plus the entire rear inside of the freezer section. Parts cost around... Read more
Secures the drive pulley to the transmission shaft in top-load washers. Replace if the original nut is backing off, stripped, or missing.
Plastic bushing that fits inside your washer's lid hinge for smooth pivoting. Replace if worn, cracked, or causing lid misalignment and squeaking.
This machine screw secures panels, brackets, and internal components in compatible washers. Replacing a missing or stripped fastener restores a tight fit to help reduce vibration and keep parts properly aligned.
I replaced the transmission, and a few other parts associated with the transmission. Read more
Replace your worn, cracked, or missing washer control knob assembly. Restores secure grip and clear position indicators for cycle and temperature selection.
This shipping bar was installed during appliance transport to secure moving parts and prevent damage. It should be removed before first use to allow proper operation of your washer's door mechanism. Remove this bar if your washer door won't open properly or if you hear rattling noises during operation.
This bracket secures the refrigerator door counterweight, helping the door stay balanced for smooth opening and closing. Replacing a damaged bracket restores proper weight support and prevents door sag or misalignment. What it does:
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.