Gtwwn2800d1ww Parts

This lid lock harness clip secures the lid lock wire harness to the washer cabinet or top. It keeps the wiring routed and protected to help prevent chafing, snagging, and intermittent lid-lock performance issues. What it does / common symptoms:

• Holds the lid lock wire harness in place along the cabinet/top
• Maintains proper routing to avoid pinching or rubbing on moving parts
• Reduces vibration-related wear on the wiring
• Symptoms of a failed/missing clip: loose or dangling harness, scuffed insulation, intermittent lid-lock response

• 1 lid lock wire harness clip

• Disconnect power before servicing
• Access the lid lock wiring path (lift top/remove console as required by your model)
• Release the old clip from the panel and harness; snap the new clip into the mounting hole and secure the harness
• Ensure the harness has adequate slack and is not pinched before restoring power

This lid bumper cushions your washer lid where it meets the top panel, softening closure and protecting the finish. Replacing worn or missing bumpers reduces slamming and rattles for a quieter, smoother close.

• Cushions contact between the lid and top panel to reduce slamming noise
• Protects painted/enamel surfaces from chips and scratches at contact points
• Helps the lid sit level and minimizes vibration or rattling
• Replace if the bumper is missing, cracked, flattened, or hardened

• Disconnect power to the washer before servicing.
• Open the lid and locate the bumper(s) at the front corners (on the lid underside or top panel lip).
• Pull the old bumper straight out; clean the mounting hole.
• Press the new bumper firmly into the hole until fully seated and flush; test lid closure.

This freezer door gasket creates the seal between the freezer door and cabinet to help retain cold air and reduce frost buildup. Replacing a worn or damaged gasket restores a proper seal and helps maintain consistent freezer performance. What it does:

• Forms an airtight seal around the freezer door to help keep cold air in and reduce ice buildup.
• Addresses common symptoms such as visible gaps or cracks in the seal, excessive frost/ice, or a door that doesn't close flush.
• Matches the OEM sealing profile to restore correct fit and function.
• Helps the freezer maintain stable temperatures when the door seal is intact.

• Disconnect power and remove food/ice from the freezer before beginning work.
• Clean the gasket channel/mating surface and remove the old gasket completely before installing the new one.
• Installation methods vary by model (press-in, retainer clips, or adhesive); for exact instructions.
• After installation, inspect door alignment and test closing to ensure a uniform seal.

This leveling leg threads into the base of your washer to set height and keep the cabinet stable on uneven floors. Replacing worn or missing legs reduces vibration, walking, and noise for smoother, safer operation.

• Provides an adjustable foot to level and support the washer
• Helps reduce vibration, rocking, and "walking" during spin
• Replaces stripped, cracked, or missing leveling feet
• Helps with excessive shaking, rattling noises, or out-of-balance conditions

• Disconnect power and water; pull the washer forward for access.
• Support the appliance to prevent tipping; unscrew the old leg by hand or with pliers.
• Thread the new leg into the base; adjust all feet until level front-to-back and side-to-side.
• Ensure each foot contacts the floor firmly and the cabinet is stable before use.

This defrost timer assembly cycles the refrigerator between cooling and defrost modes to prevent excess frost buildup and help maintain consistent temperatures. Replace a failed timer to restore regular defrost scheduling and reduce icing. What it does:

• Advances the refrigerator between cooling and defrost cycles on a timed schedule.
• Stops missed defrosts that can cause frost buildup on the evaporator and reduced cooling efficiency.
• Addresses symptoms such as excessive frost/ice, inconsistent temperatures, or a freezer that runs constantly.
• Acts as the control that engages the defrost heater and returns the unit to cooling when the cycle finishes.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Access the timer via the control panel or rear service area; document wiring or take photos before disconnecting.
• Install the timer in the same orientation and reconnect wires to the original terminals; do not force connectors.

This is the drain solenoid housing for a dishwasher. It secures and aligns the drain solenoid on the pump assembly so the drain valve actuates consistently and the tub can empty at the right time.

• Positions and insulates the drain solenoid on the pump/drain mechanism
• Maintains proper alignment for reliable drain-valve actuation
• Common symptoms of a failed housing: won't drain or drains intermittently
• May present as loud humming from the solenoid or visible cracks/heat damage on the housing

• Disconnect power and water supply before servicing
• Access the pump area beneath the tub; note solenoid, lever, and linkage orientation
• Transfer the existing solenoid and any clips/brackets to the new housing; reuse fasteners
• Run a short cycle to ensure proper draining after reassembly

This screw is a factory fastener used to secure appliance components. Replace a missing, stripped, or corroded screw to keep panels, brackets, and assemblies tight and help prevent vibration or rattling from loose hardware.

• Secures panels, brackets, and internal assemblies at their mounting points
• Replaces lost, rusted, or stripped hardware for a solid, reliable hold
• Helps reduce vibration, rattling, or shifting caused by loose fasteners
• 1/4-20 thread per OEM designation for proper fit where specified

• Disconnect power and, if applicable, shut off water supply before servicing
• Start threads by hand to avoid cross-threading, especially in plastic
• Tighten snugly; do not overtighten to prevent stripping or cracking
• Verify alignment and stability of the secured component after installation

This replacement fan blade mounts to the fan motor to move air through the system, restoring proper airflow and helping maintain stable temperatures while reducing unwanted noise and vibration. What it does:

• Attaches to the fan motor shaft to circulate air through the appliance
• Drives airflow across coils and compartments to support proper cooling
• Helps maintain even temperatures and stable performance
• Common symptoms include rattling/whirring noises, weak airflow, warm spots, or wobbling due to a cracked or warped blade

• Disconnect power before servicing
• Access the fan housing; remove any guards/shrouds as needed
• Transfer and reuse the existing retainer/clip or fastener and fully seat the blade on the motor shaft with correct orientation
• Spin by hand to ensure free clearance; reassemble and test for smooth, quiet operation

This is the refrigerator's sealed-system compressor. It pressurizes and moves refrigerant through the system to remove heat from the cabinet, restoring consistent cooling performance when the original compressor has failed or lost capacity. What it does and common symptoms:

• Pumps and circulates refrigerant through the evaporator and condenser to remove heat
• Maintains target temperatures in both fresh food and freezer sections
• Symptoms of failure can include: no cool/poor cooling, unit warms up after short operation, humming then clicking from the compressor area, or repeated thermal overload trips
• Runs but not cool effectively when the compressor is weak or internally damaged (after ruling out start components and charge issues)

• 1 compressor

• Disconnect power before servicing; sealed-system work involves high pressure and high temperatures
• Sealed-system repairs require EPA Section 608 certification and specialized tools (gauges, vacuum pump, brazing equipment)
• Replace the filter-drier, braze connections properly, evacuate to deep vacuum, and charge to the model's specification
• Related components (start device/overload, run capacitor, controls) are tested before condemning the compressor

This tub assembly replaces a cracked or leaking wash tub to restore proper water containment and drum support for your washer, helping reduce leaks, rubbing noises, and abnormal vibration during cycles. What it does:

• Provides the sealed reservoir that holds wash water and supports the inner drum during wash and spin cycles
• Helps stop or reduce water leaks caused by cracked or damaged tubs
• Can resolve rubbing, scraping, or thumping noises from a warped or broken tub
• Helps stabilize the drum to reduce vibration and improve spin performance

• Disconnect power and shut off water supply before starting; wear gloves and eye protection
• Tub assemblies are heavy and bulky—use two people or appropriate lifting equipment
• Follow the washer OEM service manual for disassembly, seal transfer/replacement, and torque specifications
• If bearings, seals, or mounting hardware show wear, replace them per OEM guidance for a complete repair

Transmission drive pulley nut.

Includes 12 washers.

This nonmetal shim acts as a precise spacer/isolator within an appliance assembly to set correct clearance and alignment between parts. Replacing a worn or missing shim can reduce vibration, prevent rubbing, and help maintain smooth operation.

• Maintains proper spacing between mating parts to ensure correct alignment
• Helps reduce vibration, rattling, and premature wear from parts contacting
• Nonmetal construction provides electrical isolation and resists corrosion
• Common signs of a bad/missing shim: scraping noises, visible misalignment, or excess play at the joint

• Disconnect power and shut off water/gas supplies as applicable before servicing
• Match the new shim to the original thickness/position; some assemblies use multiple shims—reinstall in the same locations and order
• Clean mating surfaces and inspect related fasteners/brackets; replace any distorted hardware
• Tighten fasteners evenly to manufacturer specifications and verify smooth, interference-free movement after reassembly

This small bushing fits the washer's lid hinge to provide a smooth, stable pivot. Replacing a worn hinge bushing restores proper lid alignment and helps reduce squeaks, rubbing, or excessive play when opening and closing the lid. What it does:

• Acts as a low-friction sleeve between the hinge pin and bracket
• Supports smooth lid movement and helps maintain alignment
• Reduces metal-on-metal wear and hinge noise
• Symptoms of wear can include squeaking, binding, scraping, or a loose/wobbly lid

• 1 hinge bushing

• Disconnect power before servicing
• Support the lid to prevent it from dropping when the hinge is loosened
• Remove hinge hardware to access and swap the bushing; reassemble and check lid alignment
• Many models use a bushing on each hinge—inspect both sides and replace as needed

This hex-head sheet metal screw secures appliance panels, brackets, and trim for a tight, rattle-free fit. Replace missing or stripped fasteners to keep covers and components firmly in place and restore proper alignment.

• Fastens sheet-metal parts, brackets, and trim using a hex drive
• Replaces worn, rusted, missing, or stripped screws
• Helps reduce vibration and rattling from loose panels
• Common signs you need this fastener: head or threads stripped, screw won't tighten, panel or handle coming loose

• Unplug the appliance before service; turn off water supply if working near water lines
• Use the correct nut driver or socket to avoid rounding the head
• Replace one fastener at a time to maintain alignment; do not overtighten
• Match screw type/length to the original location as specified by the manufacturer

This harness wire tie secures and organizes the appliance's wiring harness. Replacing a damaged or missing tie keeps wires properly routed and protected to help prevent chafing, disconnections, and vibration noise for more reliable operation. What it does:

• Bundles and anchors wiring harnesses along the intended routing path
• Helps prevent wire insulation from rubbing, pinching, or wearing through
• Reduces rattling or vibration noise from loose wires
• Common signs include a broken/missing tie, dangling wires, or visible wear on the harness

• 1 harness wire tie

• Disconnect power before servicing; allow any moving parts to stop
• Note original wire routing and mounting location; take a photo for reference
• Install the new tie at the same point and snug it just enough to secure without crushing wires; trim excess strap
• Verify wires are clear of moving or hot components before restoring power