Gu1200xtlso Parts

Replacement plate holder clip assembly that secures the appliance's glass plate or tray to the drive hub, helping restore stable, even rotation and reduce wobble or slipping during use. What it does:

• Secures the glass plate or tray to the drive hub so it rotates evenly
• Helps prevent the plate from wobbling, scraping, or slipping out of position
• Can reduce noisy or irregular turntable movement
• Supports consistent heating by keeping the plate aligned

• Disconnect power before servicing the appliance to avoid electric shock
• Remove the glass plate and turntable support to access the clip; handle glass carefully
• Press the clip onto the drive hub or shaft until fully seated
• After installation, reinstall the plate and run a short test cycle to ensure smooth rotation

For spray arm seal use WP8268340.

This upper rack pivot clip secures the tine/pivot on the dishwasher's upper rack so the rack stays aligned and tracks smoothly. Replace a damaged clip to stop the rack from sagging, tilting, or coming off the track. What it does:

• Secures the upper rack tine/pivot to the rack frame for stable operation
• Keeps the upper rack aligned and prevents tilting or sagging during loading
• Helps the upper rack engage and slide smoothly along the rails
• Common replacement when the rack pops off track, pivots unexpectedly, or tines become loose

• Disconnect power to the appliance before beginning any service
• Remove the upper rack to access the pivot area for easier installation
• Align the clip with the tine/pivot and press or snap into place; reuse original fasteners if present
• Handle rack tines carefully — they can be sharp; test rack movement after installation

This rinse aid sensor detects the presence/level of rinse aid and signals the dishwasher control so the dispenser and cycle logic respond correctly. Replaces a failed sensor to restore proper rinse-aid detection. What it does

• Acts as a reed-style sensor that notifies the control when rinse aid is present
• Helps the dispenser and control board make rinse-aid–related decisions
• Commonly replaced when rinse-aid indicators fail or rinse-aid detection errors occur
• Small, low-voltage sensing device used in the dishwasher dispenser area

• One rinse aid sensor (reed switch)

• Disconnect power to the appliance before starting any service
• Access may require removing the door inner panel or dispenser assembly; follow the service manual
• Handle gently and avoid bending the sensor leads; ensure secure electrical connections

Color: Bisque

This replacement cupshelf mount clip secures the cup shelf/bin inside the refrigerator door so items stay stable and the shelf functions correctly. Durable plastic clip restores proper shelf alignment and retention. What it does

• Secures the cup shelf/bin to the refrigerator door so the shelf stays in place.
• Helps prevent the door shelf from tilting or falling when loaded.
• Restores proper engagement when the original clip is cracked, broken, or missing.

• One mount cupshelf clip.

• Unload the door shelf/bin before replacing the clip to avoid dropped items.
• Typically snaps into place—align the clip and press until it seats; use a flat tool only if needed.
• Inspect adjacent door components for damage and replace any worn parts for best fit.

A flat washer used with fasteners on select top-load and front-load washer assemblies to distribute load and prevent loosening. Replaces worn or missing washers to help stabilize mounting points and reduce vibration where metal parts join. What it does:

• Provides a smooth bearing surface between a bolt or nut and the mating part
• Helps distribute clamping force to prevent damage to housings or panels
• Reduces loosening from vibration or thermal cycling
• Common fix when mounting hardware is loose, rattling, or causing leaks at joins

• Inspect mating bolt, nut, and surface for wear or damage before installing
• Use correct size and orientation; do not overtighten fasteners
• Disconnect power to the appliance and follow safety procedures when accessing internal parts
• Replace all related fasteners to ensure proper fit

This bezel vent deflector covers and directs dryer exhaust while keeping the vent opening neat and protected. It restores proper airflow path and prevents clothes or lint from catching on the exhaust opening. What it does:

• Guides exhaust air from the dryer to the vent outlet for better airflow
• Protects the vent opening from snags, debris, and visible wear
• Helps reduce lint escape at the cabinet opening and keeps the area tidy
• Replaces cracked, warped, or missing vent bezel that can affect exhaust performance

• One bezel vent deflector

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access the vent area per your model's service instructions (rear or front panel removal may be required)
• Align tabs/clips and press into place; replace any broken retaining clips or screws as needed
• Clean the ductwork and lint trap before reinstalling

This left-hand door hinge supports and pivots the door so it opens smoothly and closes tight. Replace a worn hinge to correct sagging, rubbing, or doors that won't seal—improving performance and preventing damage. What it does:

• Provides the pivot point for the door on the left side
• Maintains alignment so the door sits level and latches/seals properly
• Helps the door open and close smoothly without binding
• Common symptoms: door sags or rubs, won't close fully, uneven gaps, squeaking/grinding noises, poor seal

• One left-hand door hinge

• Disconnect power; also shut off gas and/or water before servicing
• Support or remove the door before unfastening the hinge; some hinges may be under spring tension—use caution
• Transfer original hardware/shims as needed and tighten fasteners securely
• Check door alignment and gasket contact after installation; open/close several times to ensure smooth operation

• "Left-hand" is determined when facing the front of the appliance.

Right-hand door hinge that replaces a worn or damaged refrigerator door hinge to restore proper door alignment and smooth opening and closing. Helps maintain a tight seal and prevents door sag or binding. What it does:

• Supports and pivots the refrigerator door on the right-hand side for correct alignment.
• Restores smooth opening/closing and reduces rubbing or scraping at the cabinet.
• Helps re-establish a full door seal to prevent cold air loss and temperature issues.
• Addresses symptoms such as a sagging or misaligned door, noisy hinge movement, or a door that doesn't close evenly.

• Disconnect power to the appliance and remove any items from the door before starting.
• Support the door while removing hinge hardware to prevent sudden drops or damage.
• Reuse existing screws/hardware unless replacement hardware is provided; tighten securely but avoid over-torquing.
• After installation, check door alignment and gasket contact; adjust hinge position as needed to ensure proper sealing.

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

The Circulation Motor is an OEM part for Whirlpool dishwashers. It is responsible for pumping water through the spray arms to ensure thorough cleaning of dishes during the wash cycle. This motor helps maintain consistent water pressure and flow, crucial for effective dishwashing performance.

Over time, the circulation motor can fail due to factors such as motor wear, electrical issues, or blockages that cause the motor to overheat or become damaged. Regular use and the buildup of debris or hard water deposits can also contribute to motor failure.

Symptoms of a bad circulation motor include:

• Poor cleaning results
• Unusual noises during the wash cycle
• Water not circulating properly
• Dishwasher not completing cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Detergent Dispenser Assembly is an OEM part for Whirlpool dishwashers, designed to store and release detergent and rinse aid at the appropriate times during the wash cycle. This component ensures that your dishes are cleaned efficiently by dispensing the correct amount of detergent for optimal washing performance. 

Causes of a malfunctioning dispenser can include mechanical failure of the latch or spring mechanism, clogging due to detergent buildup, or electrical issues preventing the dispenser from operating correctly.

Symptoms of a bad Detergent Dispenser Assembly include:

• Detergent not being dispensed correctly, leading to poorly cleaned dishes.
• The dispenser door not opening during the cycle or failing to latch properly before starting.
• Leakage of detergent from the dispenser, indicating a seal failure.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.