Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The Heating Element is an OEM replacement part for Bosch electric wall ovens and ranges. It is responsible for providing precise heat control to oven cavities and cooking elements.
Symptoms of an inadequate heating element include:
Causes can be normal wear and tear after extended use. Exposure to splatters or residue over time may also reduce heating performance.
This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore wall ovens.
Based on the sound of arcing, one of the elements failed. The upper one tested fine; too bad, as that's the easy one to access. The lower element on my Bosch induction range is accessible from the back, but only after you pry and bend a vertical piece of sheet metal down to a 30-40 degree angle. I assume this saves Bosch a few cents on each unit during production. Before bending that panel down, I remove all vertical obstructions: 240V power cable, the wires to the warming drawer element... Read more
Fix oven overheating or temperature regulation issues with this temperature sensor. Common repair for wall ovens and ranges that won't heat accurately.
Some internet searching on the problem followed by a chat session with AppliancePartsPros and a decision to purchase both control panel board and probe (didn't want to remove the unit twice). The replacements arrived within 36 hours and my daughter (50 years) helped remove the oven plus replace both parts - the panel was above the oven chambers and easy to replace. And the probe was okay too. I'm in my mid 70s. The panel required the nylon spacers to be re-used and these took half an hour to... Read more
Fix an oven that won't reach set temperature or shows inaccurate readings. This temperature sensor monitors heat levels for proper cooking performance.
Guessed it must be either a heat sensor or a lower element. Bosch wall oven with no easy access to the back of the stove. Had to remove the door (very Heavy) to more easily access the temperature sensor. I thought from a video that the sensor could be easily replaced without having to access the red of the stove - not true! The sensor wire was secured to other wires and a clip screwed into the sheet metal. I was able to remove all screws with a Torx head driver. Since I had to pull the unit out... Read more
The Heating Element Oven is an OEM part compatible with Frigidaire and Electrolux wall ovens and ranges. It generates targeted heat through accurate temperature coils to provide consistent, reliable baking and broiling. The oven element ensures warm, golden finishes for any recipe.
Causes of a damaged element include mineral buildup impeding heat transfer. Physical bending or cracking of fragile coils can occur from accidental impact over years of use.
Symptoms of a failed element are:
Replacing with this genuine OEM part restores optimal performance. Compatible with Kenmore, Gibson, and some Admiral wall ovens.
Fix an oven that won't heat, overheats, or shows error codes with a new control board. Moderate DIY repair requires Torx drivers and 1-2 hours.
Replaced the control module # AP5646146. Drew a layout of the connections before. Read more
This dishwasher water sensor monitors wash-water conditions so the control can adjust cycle time, rinses, and heating for consistent performance. Replace a failed sensor to restore reliable cleaning results and proper automatic cycle adjustments. What it does
Replaced Read more
Oven won't heat after self-clean cycle? A failed temperature limiter (high-limit thermostat) cuts power to protect against overheating. Direct fix.
Uneven baking or slow heating in convection mode? A failed convection fan motor stops hot air circulation. Moderate DIY repair restores even cooking.
Fix a broken or loose oven control knob that won't turn or adjust temperature properly. Direct replacement for Bosch wall oven temperature control knobs.
Oven overheats or shows E115 error? The temperature limiter (safety thermostat) may have failed. Moderate difficulty repair requiring careful disassembly.
Forced door open, replaced electric lock assembly and high limit temp switch . Large amount of disassembly required and patience. All working well need to check convection fan next. Read more
Oven not heating evenly or baking properly? This heating element restores consistent heat distribution. DIY-friendly repair with basic tools.
Removed oven from wall after opening electrical supply breakers, removed about 40 torx screws to access element and replaced. Reversed order to reassemble, tested operation, congratulated self. Read more
Electronic user-interface board that lights the display and reads button inputs. Replace when display goes dark, buttons stop responding, or error codes appear. Verify fit with your model number before ordering.
Wall oven won't start or controls acting erratic? The electronic control board directs power and timing to all components. Moderate DIY repair.
This is the evaporator fan motor and blade assembly that circulates cold air across the evaporator and throughout the fresh food and freezer compartments for even cooling and proper temperature control.
Replaced cooling fan Read more
This Terminal Box is an OEM part for Bosch Built-In Ovens. Integral to the oven's electrical system, this component serves as a secure connection point for various electrical wires within the appliance.
A common issue with a malfunctioning Terminal Box is loose connections or damage to the terminal block due to heat exposure or aging.
Symptoms of a defective Terminal Box may include:
This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
Removed and replace Read more
Fix a wall oven feature that stopped responding or works intermittently. This switch restores reliable on/off control by replacing worn contacts.