Hps15bthrww Parts

This center hinge supports and pivots the refrigerator door at the middle of the cabinet. Replacing a bent or worn hinge restores smooth door movement and a reliable seal to help maintain proper temperatures.

• Supports door weight and provides the center pivot for opening and closing
• Helps maintain door alignment for even gasket contact
• Wear or damage can cause sagging, rubbing, squeaks, or doors that won't close/seal
• Visible bending, looseness, or a damaged hinge bracket/pin indicates replacement is needed

• Disconnect power and remove items from the door to reduce weight
• Support the door and have a second person assist; note the order of any spacers/washers
• Remove mounting screws, replace the hinge, and reinstall while keeping the door square
• Verify the door swings freely and the gasket seals evenly; adjust alignment as needed

This leveling leg supports and stabilizes the refrigerator cabinet. Adjusting it keeps the unit level so doors align and seal correctly, helping reduce vibration and noise for smoother, more reliable performance.

• Threads into the base to support and level the appliance
• Allows height adjustment for proper door alignment and gasket contact
• Helps reduce rocking, vibration, and rattling noises
• Resolve issues like doors not closing fully, uneven gaps, or a wobbly cabinet

• Disconnect power and move the appliance carefully to access the leg
• Use a helper and protect flooring; tip the unit slightly and support it securely
• Unthread the old leg; hand-thread the new leg, then adjust as needed with a wrench
• Level front-to-back and side-to-side; avoid cross-threading or overtightening

This plug button is a small snap-in cap used on refrigerators to cover exposed holes on door handles, liners, or trim. It restores a clean, finished look while helping keep dust and moisture out of the cabinet.

• Snaps into a screw or access hole on a handle, liner, or trim panel
• Covers fasteners and gaps for a clean, finished appearance
• Helps block dirt and moisture from open holes
• Typical symptoms: missing cap, broken or loose plug, visible screw hole or cosmetic gap

• Unplug the appliance before servicing and use caution around sharp edges
• Align the plug with the hole and press straight in by hand until fully seated and flush
• For handle screw holes, tighten fasteners first, then install the cap
• Avoid using metal tools on finished surfaces to prevent scratches

This assembly mounts on the refrigerator compressor and combines the PTC start relay with a thermal overload protector. It helps the compressor start reliably and cuts power if overheating occurs to protect the motor and maintain cooling performance.

• Supplies initial start current to the compressor via the PTC relay
• Opens on overcurrent/overheat to prevent compressor damage
• Common failure symptoms: compressor won't start, repeated clicking/buzzing from compressor area, warm refrigerator/freezer, short cycling
• Useful when the original start device is burned, cracked, or rattles when shaken

• Disconnect power and allow the compressor area to cool before servicing
• Remove the terminal cover, note wire locations, and pull off the old start device
• Push the new start device fully onto the compressor pins and reconnect wires per the wiring diagram
• If your model uses a run capacitor, transfer/reconnect it as directed and reinstall the cover before restoring power

This compressor start relay and overload is the start device for your refrigerator's compressor. It helps the motor start and protects it from overheating, supporting reliable operation when the original start components fail.

• Provides the initial boost to start the compressor via a PTC start relay
• Overload protector opens the circuit if temperature or current is excessive
• Common symptoms: compressor won't start and repeatedly clicks
• Warm or rising fresh food/freezer temperatures
• Compressor starts then stops after a few seconds

• Disconnect power and allow the compressor to cool before servicing
• Access the compressor compartment; note wire locations and device orientation
• Pull the old device straight off the compressor pins; press the new assembly fully onto the terminals and reconnect wires securely
• Inspect connectors for heat damage and replace any burned terminals before restoring power

This top hinge and pin assembly supports the refrigerator door at the upper corner and provides the pivot point for smooth opening and closing. Replacing a worn hinge restores proper alignment and a consistent, reliable door seal.

• Supports door weight at the top and provides the pivot for smooth swing
• Maintains door alignment to prevent rubbing and uneven gaps
• Helps the door close securely for proper gasket contact
• Typical symptoms: door sags or scrapes, doesn't close flush, binds/clicks at the top, visible wobble

• Disconnect power and remove items from the door shelves
• Have a helper support the door; remove the top hinge cover and mounting screws, then lift the door straight up/off
• Position the new hinge, secure with the original hardware, and set the door back on the pins
• Adjust leveling if needed before restoring power

This control knob fits onto the refrigerator's control shaft so you can turn and set temperature or other settings. Replace a cracked, stripped, or missing knob to restore smooth operation and reliable adjustments.

• Connects to the control shaft to adjust temperature or feature settings
• Provides a secure, correct fit to prevent slipping or free-spinning
• Restores the ability to set and read the desired level
• Common symptoms: broken/cracked knob, knob won't stay on, spins freely, can't change settings

• Disconnect power to the refrigerator before servicing
• Pull the old knob straight off; gently wiggle if needed—avoid prying on the panel
• Align the flat/D-shaped opening with the control shaft and press on until fully seated
• Turn the control to verify smooth operation and proper alignment with markings

This cable clamp secures refrigerator wiring to the cabinet, keeping harnesses organized and protected. Replacing a missing or damaged clamp helps prevent chafing and vibration noise while maintaining proper clearance from fans and other moving components.

• Anchors wire harnesses in their designed routing
• Helps prevent insulation wear from rubbing or vibration
• Keeps wires clear of sharp edges and moving parts
• Common signs it's needed: missing/broken clamp, loose or dangling wires, or new rattling/buzzing noises

• Disconnect power before servicing
• Access the clamp location and note original wire routing
• Position the clamp and secure with the existing fastener; do not overtighten
• Ensure wires aren't pinched and have clearance from the fan/compressor before restoring power

This vinyl sleeve fits over a rod, tube, or wire in the refrigerator to protect and cushion contact points. It reduces wear and vibration and helps keep components aligned for smooth, reliable operation.

• Provides a protective barrier at contact points to prevent abrasion or marring
• Helps maintain spacing and alignment for a snug, proper fit
• Cushions to damp vibration and reduce rattles or squeaks
• Replace if the sleeve is missing, cracked, hardened, or if components feel loose or make noise

• Disconnect power; turn off the water supply if working near water lines
• Note the sleeve's original location and orientation; take a photo for reference
• Remove the old sleeve and any debris; slide the new sleeve into the same position
• Check clearance and resecure related parts before restoring power

Size: 10-16 ab.

8-18 CA HX 1/2 S

This small hardware clamp is used on select refrigerators to secure tubing or wiring to the cabinet or frame. Replaces a missing or damaged clamp to keep lines stable, reduce vibration, and help prevent rubbing or leaks.

• Secures small water tubing or electrical harnesses along the cabinet/frame
• Helps prevent vibration, rattling, and abrasion of lines
• Maintains correct routing to keep lines clear of moving or hot components
• Common clues: loose or noisy lines, chafing marks, or moisture near tubing connections

• Unplug the appliance and shut off the water supply before servicing
• Note the original location and routing; take a photo for reference
• Reuse the existing mounting screw/fastener if required; tighten only enough to hold without crushing tubing
• Restore power and water, then run and inspect for vibration and leaks

This hex-head screw secures dishwasher panels, brackets, and internal hardware so parts stay tight and rattle-free. Replace missing or stripped fasteners to restore a secure fit and reliable operation.

• Fastens panels, brackets, and other dishwasher components to the tub or frame
• Replaces a missing, stripped, or corroded screw that no longer holds securely
• Helps eliminate vibration and rattling caused by loose hardware
• Maintains proper alignment and secure mounting of parts during operation

• Disconnect power and shut off water supply before servicing
• Keep track of fastener locations and orientation for correct reassembly
• Start threads by hand; use an appropriate nut driver or socket to tighten
• Tighten snugly—do not overtighten, especially when threading into plastic

This 8-18 x 9/16 screw is a short sheet-metal fastener used to secure panels, trim and small components on appliances. It replaces missing or stripped screws to restore proper fit and reduce noise from loose parts. What it does

• Secures appliance panels, brackets and trim to prevent movement and rattling
• Holds small components in correct alignment for reliable operation
• Replaces lost, worn or stripped screws that cause gaps or loose fittings
• Common symptom link: fixes rattling panels, loose trim, or parts that shift during use

• One 8-18 x 9/16 screw

• Use the correct 8-18 driver bit and hand or low-torque power driver to avoid stripping
• Do not overtighten; snug until secure to prevent thread damage or panel deformation
• Turn power off/unplug appliance when installing near electrical components
• Keep extra screws on hand—hardware often comes in single quantities

This element holder assembly secures an oven/range heating element and keeps it positioned for even heat delivery. It restores proper element alignment to reduce arcing and prevent rubbing or uneven baking. What it does:

• Secures the bake or broil heating element to the range/oven housing
• Keeps the element properly spaced for consistent heating performance
• Helps stop element movement, rubbing, or intermittent contact that can cause arcing
• Commonly replaced when the element is loose, misaligned, or makes noise during operation

• Disconnect power to the appliance before beginning any repair
• Handle heating elements carefully—sharp edges and fragile terminals can be damaged
• Verify element alignment and secure mounting hardware; replace only as needed
• If you see damaged element terminals or insulation, replace the element