Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Seals the front edge of your refrigerator's crisper or pantry drawer pan cover to prevent cold air loss. Replace if worn, cracked, or not sealing properly.
First I ordered a new ice door seal, spring, and crank, figuring the condensation in freezer and door was caused by ice door not sealing. Turns out the solenoid for the ice door was completely rusted and was the primary cause, if it had been replaced early, it would have saved the dispenser board. What then happened was the moisture in the freezer door damaged the control board rendering dispenser controls inoperative as well as the heater around the dispenser. Now the freezer door is dripping... Read more
Fix a light that won't turn on or flickers in your refrigerator. This E12 socket replacement is straightforward with our step-by-step video guide.
When diagnosing the problem, I discovered that the ice door was not properly sealing and that the solenoid had appeared to rust/corrode forcing the door open. I replaced most of the ice dispenser internals (solenoid, crank, door, and spring) following the video. The door will now open when dispensing ice (which it does!), and will oddly stay open for a few seconds once I am finished, but does seal properly and the chute/container no longer frosts over. Read more
This non-adjustable shelf unit mounts permanently inside the refrigerator compartment to provide storage space. Replace if the shelf is cracked, sagging, or the mounting points are damaged and cannot support normal food storage weight.
I ordered the parts from you and put them right on. I had no problem at all very happy with your parts and was amazed at the time it took to get my parts. I will make sure I ordered from you again. Thanks. Read more
Fix leaking water or a non-working ice maker with this refrigerator water inlet valve. Moderate DIY repair in 30-45 minutes with basic tools.
First, I had to remove the cover plate on the back of the refrigerator. Then I unscrewed the water inlet valve from the rest of the assembly. I then unplugged the electrical contacts by pulling them apart. There are two fittings on the valve. One has a nut on it. That one just needs the nut unscrewed, after which the pex tubing can be pulled out. The other one has a pex connection. This one can be separated by simultaneously pushing in on the fitting neck while pulling the pex tubing out. On... Read more
Ice maker not filling or water dispenser leaking? This water inlet valve controls flow to your ice maker and dispenser. Most DIYers complete in 15-30 minutes.
I researched the problem online and determined it was undoubtedly the water valve leaking. A visit to AppliancePartsPros.com to order the replacement valve and I was ready to go. Actual repair only took 15 minutes. Read more
Replacement door gasket for the fresh food compartment. Creates an airtight seal to maintain stable temps and reduce condensation. Verify fit by model.
Black plastic funnel extension attaches to the front of your refrigerator's ice dispenser. Replace if cracked, broken, or missing to reduce splashing.
Me and my husband fixed it. Thanks for the help. Read more
Refrigerator not cooling but freezer works? This air damper and thermistor assembly controls airflow between compartments. Restores proper cooling.
Replaced all temperature sensors, damper, and the thermistor (all probably were not needed but I was not exactly sure the issue, but I knew my heater, compressor, and the evaporator fan were all working correctly). Read more
Right side
Replaced the support bracket for the ice bucket. Replaced the auger motor for the ice dispenser and installed the new coupler for the microwave tray to spin. Everything works great now! Read more
Mounting screw fastens panels, brackets, and trim in refrigerators, dishwashers, and ranges. Replace missing, stripped, or rusty screws to secure parts.
New parts. Read more
Ice maker not filling or water spilling? This fill cup directs water into the ice maker mold for proper ice production. Simple clip-on install.
Went online to appliance pro, found my model and the ice maker part number. The process was very easily. The order process was also very simple and the part was delivered promptly with installation instructions. Read more
Donut-shaped gasket creates a tight seal between refrigerator components. Replace when worn to stop minor leaks and restore secure fit. Verify fit with your model number.
Size: 8-18 AB TSQ 5/8 SS
I replaced the upper and mid spray arms and bearings, removed filters and screens and cleaned everything. Pulled pump and replaced the connector and the collection sump. Repair took about 3 hours and went very smoothly thanks to the AppliancePros video! I'm on the east coast so I could not believe it when the parts arrived less than 24 hours after I placed the order! Prices were great too . . . I'm a customer for life and my dishwasher cleans the dishes like new now! Read more
Flexible seal that keeps cold air in your freezer. Replace when worn, cracked, or doors won't seal properly. Confirm fit with your model number.
This was a two and half year issue as different things failed at different times. I would get one part, then another would fail. Ultimately, I got to a point where what failed, I hadn't been ordered the part yet. The seal on the freezer door took three bathing's before it plumped up and un-creased. The directions on the box it is shipped in said to heat the seal up in hot water then cool it down with tap water. I didn't need to do that. It took a lot of massaging of the seal, but... Read more
Internal water reservoir with attached tubing that stores and delivers chilled water to the dispenser. Replace if cracked, leaking, or damaged.
Installing the tank went quickly. Removed the water filter from the upper compartment to stop water flow to the tank. Had to remove the two lower drawers (they tilt out of their sliding frames). There is a glass shelf that should be pulled out - it slides out via two notches in the front frame. The water tank is behind a white metal cover held by 4 screws. Keep track of all of the parts including the lip seals from the shelf. I used two Watts 5/15x5/16 couplers from Lowes for the connections.... Read more
Secures the condenser fan motor in position. Replace this bracket if cracked, bent, or causing excessive vibration to restore stable mounting.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.