Hss25gfta Parts

The front wheel assembly replacement (WRXO2X12454) was straightforward and easy to do. Took maybe 30 minutes start to finish. The rear wheel assembly (wheel WRO2X10695 and axle WRO1X10604) that was more involved as the original wheel axle is actually a rivet that you have to cut out. 1. I used a vibrating multitool with a carbide blade to cut the axle out. Had to use a pair of vise grips to hold the rivet to keep it from spinning while cutting it. 2. The new axle I drilled a 2mm hole thru the... Read more

Replaced Ice maker very easy. Read more

Replaced all four cams. It was very easy to do. I didn’t even have to turn off the fridge. You should though when touching electrical connections. The hardest part was aligning the pegs with the holes by myself. Hard to do when balancing the door. Otherwise piece of cake. Thanks guys. Read more

Swapped it out for new tube. Take 5 minutes and zero effort. The drain tube will clog with mold. You can clean it out but the tube will clog again despite's you best efforts as the tube wall provide a great habitat. Ordered new tubes to facilitate swap-outs. Old tubes can be cleaned but will recolonize quickly. Read more

First I ordered a new ice door seal, spring, and crank, figuring the condensation in freezer and door was caused by ice door not sealing. Turns out the solenoid for the ice door was completely rusted and was the primary cause, if it had been replaced early, it would have saved the dispenser board. What then happened was the moisture in the freezer door damaged the control board rendering dispenser controls inoperative as well as the heater around the dispenser. Now the freezer door is dripping... Read more

I ordered the heater unit from your website as well as a new evaporator panel gasket and thermostat. Once I removed the evaporator panel from the rear wall of the freezer side, I used a steamer machine I had to melt all the ice which had accumulated, I replaced the faulty heater unit and all is well. By-the-way, I consider your website amongst the very best and easy to use. I appreciate how well your developers and designers created the diagrams/pictures with numbered parts displayed,... Read more

Very easy to replace the trays slide the broken one out, slide the new one in, no problems. Read more

I ordered the recommended front door shelf part Fz for my frig, it was shipped promptly. It was slightly too long, so I cut about a 1/4" with the saw... it fits nicely now. Read more

Replacing the roller assembly corrected the problem. The key to replacing the roller assembly is elevating the refrigerator high enough to remove the roller assembly. (1) Raise and secure the refrigerator, (2) remove the metal bar across the bottom of the refrigerator to provide adequate access to the roller assembly (2-screws), (3) remove the roller assembly adjustment screw, (4) pry the roller pivot pin out, (5) pull the roller assembly toward the front of the refrigerator to remove, (6)... Read more

I found the part numbers in an exploded view of the refrigerator. They then showed that that part number had been replaced by a new one. I ordered them on line from Appliance Parts Pros. The parts arrived a few days later and, in this case, were an easy install. The refrigerator looks like new. Read more

New solenoid Read more

I made the right initial move - I went to appliancepartspros.com and located the necessary parts. A video convinced me I could make the repairs myself. The correct parts were easily ordered and arrived quickly. I had no problem installing the parts using the knowledge I gained from the appliancepartspros.com video and the leak was fixed. Read more

I had 2 parts that were cracked, so after changing the cracked parts as well as the dispenser switch, it was back to working normally. Simple to make the needed repairs and the videos provided on your website really helped in being prepared. Read more

I ordered the Cover Pan glass, glass front gasket and gasket lower shield. The diagrams on Appliciancepartspros.com were very helpful in ordering the correct parts. Once the parts arrived at the house, I put the gaskets on the glass and slide the glass into place. Read more

Very easy to replace the trays slide the broken one out, slide the new one in, no problems. Read more

1) By using google to find videos on why the door wouldn't close, I found out I needed new cams, those same videos also showed how to remove and replace the door. 2) Then by googling the fridge model number and the word 'cam', I was able to find the parts. 3) Taking the door off was simple, I needed a phillips head screwdriver to remove the hinge cover, however the screws in the hinge plate were so tight, I needed a side handle socket wrench to loosen them. 4) The door itself is not hard to... Read more