Htwp1200doww Parts

This left end cap is a molded replacement trim piece that restores the finished edge and appearance of the appliance door. It replaces a cracked, broken or missing cap to keep the door trim secure and looking original. What it does:

• Covers and protects the left edge of the door trim or hinge/handle end for a finished appearance
• Hides mounting hardware and helps keep the trim aligned
• Prevents sharp edges or exposed holes that can catch on clothing
• Common symptom: visible crack, broken corner, loose or missing end cap causing an unfinished look

• Install with basic hand tools; verify orientation for the left side before fastening
• Handle parts carefully to avoid scratching the finish during installation
• Disconnect power only if needed to access components near wiring — otherwise follow normal appliance safety practices
• If mounting hardware is missing or damaged, replace only with manufacturer-recommended fasteners

This tub-bearing split ring is an OEM replacement part designed for GE washing machines. This part measures 2 inches in diameter. It is positioned between the inner and outer tubs to hold the tub bearing inside the outer tub. The Tub Bearing Split Ring not only supports the tub/hub assembly but also ensures smooth operation. 

Symptoms of a bad Tub Bearing Split Ring include:

• Excessive vibration or tub imbalance during spins  
• Loud clunking, knocking or grinding sounds  
• Reduced spin speeds or inability to achieve high RPMs
• Premature tub or bearing wear requiring replacement

Causes can be extended use over time which leads to wear and fatigue of the split ring material. Cracks or breaks can develop, reducing its stability and load-bearing capacity.

This genuine GE replacement part is also compatible with Hotpoint, RCA and some Kenmore front-load models. 

NOTE: For the washer outer tub seal order WH02X10383.

The Knob Clip is an OEM part for GE washing machines and dryers. This small but crucial component is designed to secure the control knob to the appliance's control panel.  

Over time, knob clips can wear out or break due to frequent use or accidental damage. When this happens, the control knob may become loose, fall off easily, or fail to engage the control panel properly, making it difficult to set the appliance to the desired cycle or function.

Symptoms of a bad Knob Clip include:

• The control knob is loose or falls off the panel easily.
• Difficulty in adjusting settings due to a loose knob.
• The knob does not stay in place or slips when turned.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Washer Top is an OEM part for GE washers. It is the upper panel that covers the internal components of the washing machine and provides a flat surface for loading and unloading laundry.

Causes of a bad Washer Top can include physical impact, warping due to prolonged exposure to heat or moisture, or general wear and tear over time.

Symptoms of a bad Washer Top include:

• Visible cracks, dents, or damage to the top panel
• Difficulty opening or closing the lid due to misalignment or warping
• Water leaks around the top area during wash cycles
• Excessive noise or vibration caused by a loose or damaged top

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This genuine OEM part is a drive motor for washers. The drive motor is the main engine that drives the washer tub allowing it to rotate and wash clothes effectively. If the washer is no longer spinning or the power has significantly decreased, it might be a sign that the drive motor needs to be replaced. Luckily, replacing this part is a relatively simple repair.To replace the drive motor, start by unplugging the washer. Once unplugged, move the washer away from the wall to gain access to the back panel. Uninstall the back panel by removing the screws that attach it. After removal, locate the drive motor and proceed to unthread the mounting screws holding it to the washer. Proceed to pull the old motor out of its place and install the new motor by threading the screws that secure it. This replacement part is sold individually and is compatible with GE, RCA, and Hotpoint brand washers.