Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replacement actuator pad for refrigerator water and ice dispensers. Snaps into dispenser panel. Replace if cracked, broken, or tabs are damaged.
Super easy fix, remove two screws behind drop tray, unplug the wiring harness to dispenser, unplug and remove old pad, then snap new one into place. Reconnect harness. Took less than 5 minutes, works like new. Read more
Replacement crisper drawer for your refrigerator's produce compartment. Restores organized storage for fruits and vegetables when original is cracked or broken.
Grey decorative cap that covers the water filter housing on side-by-side refrigerators. Replace if cracked, broken, or missing for a finished look.
I replaced the pads on my Kitchenaid side-by-side. I was able to order ones that looked exactly like the old ones. It was even easier than what I had seen in a YouTube video. Read more
Ice bin won't release or latch broke? This ice bin latch spring provides tension to secure the ice container properly. Easy 10-minute DIY fix.
Easy to remove the metal parts from the old bin. The only problem was that the screw that holds the adapter has red thread locker and screwdriver rounded off the head of the screw. Drilled the screw and heated the screw to loosen the thread locker and used an ease out to remove the screw. Read more
Replacement fastener screw for appliances. Secures panels, trim, clips, and components. Needed when original screws are stripped, missing, or damaged.
Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on... Read more
1/4 inch compression nut for securing plastic water lines in refrigerators and ice makers. Replace worn, cracked, or missing nuts to prevent leaks.
Ordered part from AppliancePartsPros.com and received it 2 days later. Put the part in, fit like a glove, water and ice cube maker working flawlessly again with no leaks. Thanks. Read more
Ice falling out of dispenser or chute door won't close? This door chute directs ice flow and seals properly. Typical 30-minute DIY fix for dispensers.
Talked to a service rep. and he helped me diagnose what was needed. Read more
Replacement spring for refrigerator ice dispenser chute door. Restores closing tension when original is fatigued, broken, or missing. Installs on strike arm.
We ordered the Ice Door Fountain Kit and ice door spring, which was delivered to our home within three or four days. I understood everything about how to change it except the placement of the spring. A video on your website showed exactly how to put the spring in place and helped me get the job done quickly. It solved our problem and we really appreciate your services. Read more
This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more
This replacement ice bucket housing encloses and supports the freezer's ice storage bin at the dispenser. A damaged housing can cause bin wobble or misalignment—replacing it restores a secure fit, smoother dispensing, and helps reduce stray ice and frost.
The removal of the ice bin and auger motor was easy but removing the auger from the shaft was another story. The auger was frozen to the shaft even after it sat out overnight. I carefully applied heat with a propane torch, directly on joint of the auger and the tip of the shaft, followed by a few drops of cold water. Once the shaft and auger cooled the auger separated easily. Putting the components back together was simple taking about ten more minutes. Read more
Replaces worn or broken refrigerator door closer cam that installs at the bottom hinge. Restores smooth door action when the original is cracked or damaged.
Watched the video at Appliance Parts Pros. Followed the video. I was fixing the refrigerator door (a little easier then the freezer door). The repair was very simple and took less then 15 minutes. Read more
Replacement support stud that holds refrigerator shelves securely in place. Needed when original peg is broken, cracked, or missing from shelf wall.
Myself Read more
Ice maker water line: 1/4x 8ft.
Replaced the broken parts. The water leak was caused by the drain valve not directed into drain pan Read more
Secures the bottom grille to your refrigerator frame. Replace if the original clip is cracked, broken, or missing and the grille won't stay in place.
Easy fixes, but I did what one of your video clips Read more
Fix ice maker overfilling, water leaks, or no water dispensing. This refrigerator water inlet valve kit replaces older Y-type valves. Video guide included.
I replaced the dual outlet valve which did not fix it then i replaced the inlet valve which fixed it Read more
The Screw is an OEM part for Whirlpool refrigerators. This screw secures the refrigerator door hinge in place, allowing the door operates smoothly and seals properly.
Over time, screws can become loose or go missing during repairs or adjustments, which can lead to a misaligned door, compromised sealing, and increased energy consumption.
Symptoms of a bad screw include:
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
As soon as the parts arrived, installed them seamlessly. Thank you. Read more