Jgd8345abd Parts

Sealed burner assembly that supplies a protected gas flame for a gas range, restoring consistent heat and helping keep spills and debris out of the burner box. Designed as a direct-replacement assembly for affected burners. What it does

• Provides the sealed gas flame source used for cooking on a gas cooktop
• Restores even heat distribution when a burner is warped, damaged, or not producing a steady flame
• Helps prevent spills and food debris from entering the burner cavity, reducing corrosion and ignition problems
• Symptom linkage: commonly replaced for uneven heating, weak or irregular flame, visible burner damage, or excessive soot

• Includes 1 sealed burner assembly

• Turn off the gas supply and electricity to the appliance before starting any service
• Follow model-specific disassembly steps (lift or remove cooktop/grates as required); do not force fittings or gas connections
• If you smell gas, shut off the gas supply immediately

• WP3403M075-29 — confirm this matches your original part before ordering

Left-side gas valve that controls gas flow to the burner assembly, restoring reliable ignition and stable flame control when a faulty valve causes burners to fail to light, sputter, or produce an inconsistent flame. What it does:

• Regulates gas flow to the left burner assembly for proper ignition and steady flame control.
• Replaces a stuck, damaged, or failed valve often associated with burners that won't light, have weak flames, or flame fluctuation.
• Acts as the control point between the appliance gas supply and the burner; proper operation is required for safe ignition.
• Use the appliance's parts diagram to determine left/right valve location and fit before ordering.

• Turn off the appliance power and shut off the gas supply before starting any service.
• Only install on appliances designed for this left-side valve; follow the service diagram and manufacturer instructions for proper fitment.
• Inspect all fittings and connections for leaks after installation; test using approved leak-detection methods per local codes.

This sheet-metal pan-head screw secures appliance panels, brackets, and components to the cabinet or frame. Replacing a missing or damaged screw restores a tight fit and helps stop rattles, misalignment, and loosening.

• Fastens sheet-metal panels, covers, ducts, and brackets to the appliance chassis
• Helps keep components aligned and secure during operation
• Replace if the original is missing, rusted, stripped, or damaged
• Common symptoms: loose or vibrating panels, gaps or misaligned parts, hardware that won't tighten

• Disconnect power; shut off gas or water supply before servicing
• Support the panel or part being attached; hand-start threads to avoid cross-threading
• Use the correct driver bit; tighten snugly but do not overtighten into sheet metal
• If multiple matching screws secure a part, consider replacing them as a set for consistent hold

The Regulator is an OEM replacement part for Whirlpool gas ranges. It regulates the flow of gas from the supply line to the burners, ensuring safe and efficient operation of your range. It maintains a consistent gas pressure, allowing for accurate and controlled heat distribution during cooking.

A bad pressure regulator can occur due to wear and tear, clogging, or damage to the internal components. If you notice symptoms such as uneven flame, difficulty in igniting the burners, or gas leaks, it may be time to replace the pressure regulator.

Symptoms of a bad gas pressure regulator include:

• Uneven flame
• Difficulty in igniting burners
• Gas leaks

This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

Replacement top surface burner valve that controls gas flow to a single surface burner for safe, consistent flames. Restores burner operation when the control knob no longer ignites or adjusts the flame. What it does:

• Regulates gas flow from the manifold to one top/surface burner so the flame lights and responds to the control knob.
• Replaces valves that stick, fail to open/close, or stop adjusting flame size.
• Common symptoms this part can address: burner won't light, knob turns without affecting flame, flame too low or uneven.
• If you smell gas or suspect a leak, shut off the gas immediately.

• (1) top surface burner valve

• Shut off the gas supply and disconnect power to the appliance before starting; relieve any residual pressure per your appliance instructions.
• Use correct tools and replacement gaskets/seals where required; only install if part number matches your model.
• After installation, check all connections for leaks using a safe leak-test method (soapy water), not an open flame.

A replacement SN switch that restores the appliance's control function so selections and features respond reliably. Installs in the original switch location to return consistent on/off or selector operation after a switch failure. What it does:

• Opens and closes the electrical circuit to control the associated function or component.
• Replaces a worn or failed switch to stop intermittent operation or loss of control.
• Common symptoms it can fix: appliance not responding to a selector/setting, intermittent power to a component, or a component that won't turn on.
• Functions as the user-facing or internal control switch depending on the model application.

• Disconnect power (unplug appliance or shut off breaker) before starting any repair.
• May require removing an access or control panel; use basic hand tools and note wire locations before disconnecting.

A single pop rivet used to secure sheet-metal parts and small brackets on appliances for a permanent, vibration-resistant hold. Replaces missing or damaged rivets to restore proper attachment without welding. What it does:

• Provides a permanent blind-rivet fastening point for panels, brackets and trim.
• Replaces rivets that are sheared, loose or missing and prevents rattling or misalignment.
• Ideal where a solid, tamper-resistant join is required and screws aren't suitable.
• Works with a compatible pop-rivet tool for quick installation.

• Drill out the old rivet carefully; use the proper size hole for the replacement rivet.
• Use a dedicated pop-rivet tool and wear eye protection during installation.

This single valve switch is the electrical control that activates a single solenoid valve, restoring proper valve operation so the appliance can open or close the water/flow circuit as designed. It replaces a failed or non-responsive valve control switch. What it does

• Sends the electrical signal to a single solenoid valve so the valve opens or closes when commanded.
• Commonly used when a valve fails to energize, causing no water flow or intermittent operation.
• Helps resolve symptoms such as the valve not activating, intermittent dispensing, or an appliance that won't fill.
• Works as the user-commanded switch interface between control electronics and the valve assembly.

• One (1) single valve switch

• Disconnect power to the appliance before starting any repair to avoid shock.
• Turn off the water supply if the repair requires disconnecting water lines.
• Verify connector orientation and secure electrical connections; do not force connectors.

The surface/top burner valve controls gas flow to a cooktop/range burner, letting you turn the flame on and adjust heat. Replacing a worn valve restores smooth knob feel and consistent ignition and flame control on your gas appliance.

• Regulates gas supply to the surface burner from Off to simmer to full flame
• A stiff or seized stem can make the knob hard to turn or stuck
• Failure can prevent the burner from lighting or cause erratic flame adjustment
• A stripped/broken shaft may let the knob spin without changing flame

• Disconnect power, shut off the gas supply, and allow the appliance to cool
• Remove the knob and access panel to reach the valve; label tubing and any wires for correct reassembly
• Transfer any orifice fittings and mounting hardware from the old valve as required; align the stem for proper knob orientation
• Use gas-rated sealant on pipe-threaded joints only and leak-test all connections with a non-corrosive solution before restoring service.

The front venturi is the front section of the burner venturi tube that mixes air with incoming gas for proper burner combustion. Replacing a damaged or clogged venturi helps restore reliable ignition and a steady flame. What it does:

• Directs and mixes air with gas before the burner to support stable, even flames.
• A worn, cracked, bent, or clogged venturi can cause weak flames, uneven heat, or difficulty lighting.
• Sits at the front portion of the burner venturi assembly and aligns gas flow into the burner head.
• Works with the rest of the burner components to maintain proper combustion characteristics.

• Turn off gas supply and unplug appliance before servicing; follow all local codes for gas work.
• Remove burner grates and burner head to access the venturi; handle carefully to avoid deforming the tube.
• Inspect surrounding burner parts and clean any debris before reassembly.
• After reinstalling, check for correct ignition and a steady flame; perform a leak check if gas lines were disturbed.

A genuine replacement mounting screw that secures appliance panels and components to restore proper fit and reduce vibration. Use this screw to replace missing or damaged fasteners for a secure, rattle-free repair. What it does:

• Fastens panels, brackets, or components to the appliance frame
• Restores proper alignment and reduces rattling or vibration
• Prevents parts from coming loose during operation
• Works wherever the OEM screw W10828565 is specified

• Disconnect power to the appliance before servicing
• Use the correct screwdriver or bit to avoid stripping the head
• Install only where the OEM screw is specified; do not overtighten
• Replace any stripped or damaged screws with this exact part

This double valve switch assembly controls two valve circuits to manage water flow and valve operation in compatible appliances. It replaces a failed switch to restore proper valve control and appliance function. What it does:

• Acts as the electrical switching assembly for two valve solenoids or circuits
• Allows the appliance control board to open and close water valves as needed
• Commonly linked to symptoms like no fill, continuous fill, or intermittent valve operation
• Helps stop erratic or unresponsive valve behavior when the original switch fails

• One double valve switch assembly

• Disconnect power (and water, if applicable) before beginning any repair
• Verify power is off with a meter and document wire locations or take photos before disconnecting
• Handle connectors carefully; ensure proper seating and secure mounting during reassembly

Rear venturi directs the gas/air flow from the valve to the burner for proper ignition and heating. Replacing a damaged or clogged venturi helps restore consistent flame and improve dryer heating performance. What it does:

• Channels and shapes the air/gas mixture to the burner assembly for reliable ignition.
• Helps maintain consistent burner flame and steady heating during operation.
• Commonly replaced when the dryer has weak or no flame, reduced heat, or intermittent heating.
• Fits the rear mounting location and mates to the burner/gas valve interface.

• Turn off the gas supply and unplug the dryer before beginning work; only service when the appliance is cool.
• Remove the dryer rear panel or access cover to reach the burner housing and venturi; handle internal components carefully.
• Inspect gaskets and seal surfaces; replace any damaged seals and check gas connections for leaks after reassembly.

This relay change kit replaces the failed relay assembly that controls motor or compressor power, restoring proper electrical switching for normal operation. Use this kit to replace a worn or intermittently working relay with an exact-fit factory component. What it does

• Switches power to the motor/compressor when the appliance calls for it
• Restores reliable start and run signals when a relay has failed or sticks
• Addresses symptoms like clicking on start, no motor/compressor operation, or intermittent runs
• Helps prevent damage from repeated failed start attempts

• One relay change kit

• Disconnect power before servicing to avoid shock or damage
• Replace only with the exact OEM relay kit for safe, reliable operation
• Verify wiring and connectors are secure and undamaged before restoring power

This replacement control knob restores a secure grip and accurate selection of settings on your appliance's control shaft. Swap a cracked, stripped, or missing knob to keep everyday operation smooth, precise, and safe.

• Attaches to the control shaft to select temperature, cycle, or burner settings
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps resolve issues like a knob spinning freely, difficulty turning, or inability to choose a setting
• Restores normal feel and alignment when turning the control

• Unplug the appliance and, if applicable, shut off gas before servicing
• Pull the old knob straight off the control shaft; avoid prying on the stem
• Align the new knob with the shaft and press firmly until fully seated
• Test operation to ensure smooth turning and proper engagement

This replacement grate cartridge secures and centers a cooktop burner grate so cookware sits level and burners perform as intended. Durable design restores stable support for pots and pans on compatible gas ranges. What it does:

• Replaces a worn or broken grate cartridge that lets the grate rock or sit unevenly
• Helps keep the burner grate properly aligned over the burner for even cooking
• Prevents cookware from wobbling or shifting during use
• Restores proper fit where the grate attaches to the cooktop surface

• One grate assembly (cartridge) as shown

• Turn off and disconnect power and gas supply; allow the range to cool completely before servicing
• Remove the burner grate and lift out the old cartridge; align tabs and snap or seat the new cartridge into place
• Handle enamel-coated grates carefully to avoid chipping; use soft padding if needed during installation