Jvm1430002 Parts

The Hood Damper Assembly is an OEM part for GE microwave ovens. This part controls the flow of exhaust air to minimize odors and smoke from cooking. This damper opens to allow air to vent outside during microwave operation and closes to prevent outside air from entering when the microwave is not in use.

Causes of a bad hood damper assembly can include mechanical failure such as a stuck or broken damper, deterioration of the linkage or springs that operate the damper, and blockage caused by grease or debris accumulation, which can impair its functionality.

Symptoms of a bad Hood Damper Assembly include:

• Ineffective venting of smoke or cooking odors
• External air leakage into the microwave system
• Unusual noises during operation indicating a damper misalignment or obstruction

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This high-voltage rectifier diode is used in the microwave's high-voltage circuit. It converts AC to DC so the magnetron can produce heat. A failed diode can cause no heat, loud humming, or a blown fuse when starting. What it does:

• Rectifies high-voltage AC to DC to power the magnetron
• Blocks reverse voltage in the HV circuit
• Common failure symptoms can include: runs but doesn't heat; loud hum then shutdown; line fuse blows at startup

• 1 high-voltage diode

• Unplug the microwave and properly discharge the high-voltage capacitor before servicing—dangerous voltage can remain even when unplugged
• Match diode orientation/polarity to the original and ensure a solid chassis ground connection where used
• Route leads and reinstall any clamps/insulators exactly as found; keep wiring clear of sharp edges and hot components
• If the original diode failed, inspect the HV capacitor and transformer for related issues before reassembly

This is the clear glass lens that covers the cooktop light on select GE over-the-range units. It shields the bulb from grease and splatters while allowing bright, even illumination of the cooking surface below.

• Protects the cooktop light bulb from grease, moisture, and debris
• Restores proper lighting if the original lens is missing, cracked, or stained
• Helps maintain safe, even illumination of the range area
• Common symptoms: broken or missing lens, dim or uneven light due to a damaged cover

• Disconnect power to the appliance before servicing
• Allow bulbs and surrounding area to cool completely
• Handle glass carefully to avoid chipping; wear cut-resistant gloves
• Ensure the lens seats fully and any retaining tabs/screws are secured per the product's service instructions

Color: brown. It measures about 8-1/2 inches in diameter.

The Grease Filter is an OEM Replacement Part designed to maintain the cleanliness and efficiency of your GE microwave. This filter measures 7 3/4 inches x 9 1/8 inches and is specifically designed to collect grease particles from the air while cooking. B

Causes of a bad grease filter can include regular wear and tear from frequent use, buildup of grease and cooking residues, or physical damage from cleaning or handling. Over time, the filter can become less effective at trapping grease, leading to reduced performance.

Symptoms of a bad grease filter include:

• Noticeable grease buildup on the range hood or microwave surfaces
• Reduced airflow or ventilation efficiency
• Visible damage, tears, or holes in the filter
• Unpleasant odors due to trapped grease and food particles

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

A replacement magnetron assembly that generates the microwave energy used for cooking and reheating. Installs in countertop and over-the-range microwave ovens to restore normal heating performance when the magnetron fails. What it does:

• Produces high-frequency microwave energy that heats food inside the oven cavity.
• Commonly replaces a unit when the microwave stops heating or heats very weakly.
• Can address symptoms like no/poor heating, intermittent heating, or loud humming from the oven during operation.
• Not a control or capacitor—this part is the microwave-generating tube and works with the oven's HV system.

• Always disconnect power and unplug the appliance before starting service.
• The high-voltage capacitor can retain a dangerous charge; discharge properly.
• Handle the magnetron carefully; avoid touching terminals or the antenna.
• Follow OEM instructions and safety guidelines for reassembly and testing.

Made by GE. This microwave stirrer motor comes with a square shaped shaft and is usually located in the upper part of the microwave. For a D shaped shaft turntable motor order WB26X10038.

This holder nut assembly secures a component to the appliance frame, restoring proper mounting and reducing vibration or movement. Replace a damaged or missing holder nut to keep connected parts stable and functioning. What it does:

• Secures a component or assembly to the appliance frame or mounting bracket
• Prevents looseness, rattling, and misalignment caused by worn or missing mounting hardware
• Restores a safe, stable connection that helps maintain normal operation
• Matches OEM mounting geometry for a direct replacement when the original nut is damaged

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access the mounting area by removing the appropriate panel or cover per your model's service instructions
• Start threads by hand to avoid cross-threading, then tighten with the correct tool; do not overtighten
• If any fasteners or nearby components are damaged, replace them as needed for a secure installation

This microwave thermostat is a temperature-sensitive safety switch that helps protect the unit from overheating. When the preset limit is reached, it interrupts power to the affected circuit to help prevent damage and erratic shutdowns.

• Monitors temperature at its mounting location and opens the circuit if overheating is detected
• Helps protect internal components from excessive heat
• Common symptoms of a failed thermostat include: unit shuts off during cooking, won't start until it cools down, or has no power/no heat due to an open safety
• Replace if the original tests open when it should be closed

• Disconnect power by unplugging the unit or switching off the circuit breaker before servicing
• Microwaves contain a high-voltage capacitor that can retain a dangerous charge; only qualified persons should service and discharge the capacitor
• Note wire locations before removal and transfer connections firmly to the new thermostat
• Mount the thermostat securely and in the same position to ensure proper temperature sensing

This evaporator fan motor assembly circulates cold air through the refrigerator compartment to help maintain even cooling and proper temperature control. Replacing a failed fan restores airflow and helps the appliance cool correctly. What it does:

• Moves air across the evaporator coil so the refrigerator/freezer can cool efficiently
• Commonly replaced when there is little or no airflow from the fresh-food or freezer section
• Can stop excessive frost build-up on the evaporator caused by poor circulation
• May reduce unusual noise if the original motor bearings have failed
• Helps prevent uneven temperatures that can cause food spoilage

• One evaporator fan motor assembly as shown

• Disconnect power to the appliance before starting any repair
• Access may require removing interior panels or the evaporator cover
• Handle the fan blades carefully to avoid bending or cracking; ensure proper blade seating on the motor shaft

This grille assembly replaces the refrigerator's lower kickplate to restore proper airflow and give the front a finished look. It helps protect internal components while keeping the appliance visually complete. What it does:

• Covers and protects the condenser area and components behind the lower front of the appliance
• Allows proper airflow at the cabinet base to support cooling performance
• Restores the appliance's appearance when the original grille is damaged or missing
• Helps keep pets, debris and small objects out of the lower service area

• Disconnect power to the appliance before beginning work
• Typically secures with screws or retaining clips along the toe-kick; keep hardware from the original part if present
• Align mounting tabs and engage clips/screws without forcing to avoid breakage

This control panel is the appliance's electronic user interface that lets you start cycles and adjust settings. Replacing a faulty panel restores reliable button or touch responses and on/off control of the unit. What it does:

• Provides the front user interface for selecting functions, settings, and cycles
• Transmits user commands to the range/oven control board for operation
• Commonly replaces panels that are unresponsive, intermittently working, or showing control/display errors
• Helps resolve issues where buttons, touch keys, or indicator lights don't respond

• Disconnect power at the breaker or unplug the appliance before starting
• Handle glass or plastic surfaces carefully to avoid scratches or damage
• Basic hand tools usually required; save mounting screws and brackets from the old part

This washered screw secures panels and internal components where a combined screw-and-washer fastener is required, restoring proper fit and stopping movement or rattling. Simple replacement with the correct fastener keeps assemblies aligned and stable. What it does

• Secures panels, brackets or components where a washered screw is specified
• Replaces missing, stripped or corroded fasteners that allow vibration or gaps
• Helps stop rattling, loose panels or misaligned parts caused by a failed screw
• Provides a sealed bearing surface to distribute load and prevent pull-through

• One washered screw

• Disconnect power and/or water to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid cam-out and fastener damage
• Align parts before tightening and snug; avoid over-tightening which can strip threads or crack plastic

This handle tapping screw secures an appliance's handle to its door or front panel. Replacing a missing or stripped screw restores a firm, safe grip and prevents a loose or rattling handle. What it does:

• Fastens the handle to the door or front panel
• Self-tapping design engages/cuts threads for a secure hold
• Replaces missing, rusted, or stripped handle screws
• Helps correct a loose, wobbly, or rattling handle

• One handle tapping screw

• Disconnect power before service; for gas ranges, also shut off gas
• Support the handle while removing/installing screws to avoid stressing glass or trim
• Start the screw by hand to avoid cross-threading; tighten snugly without overtightening
• Keep track of any decorative end caps or spacers for reassembly