Kfis25xvms Parts

Fix frost buildup and grinding noises with a refrigerator defrost heater. Melts ice on evaporator coils. Video guide included for easier installation.

Replacement slide rail for refrigerator pantry or deli drawers. Installs on drawer side to enable smooth gliding. Needed when rail is bent, broken, or cracked.

Structural support that holds the crisper drawer frame in place. Replace if cracked, broken, or missing. Slides into liner holes for stability.

Refrigerator making loud noise or not cooling? A cracked or broken condenser fan blade disrupts airflow. Easy 10-minute DIY fix with our video guide.

The Drip Pan is an OEM part for Whirlpool refrigerators. Located beneath the refrigerator, it collects and holds water that drips from the defrost system, preventing it from leaking onto the floor.  

Causes of a bad drip pan can include cracks or holes from physical damage, warping from exposure to temperature fluctuations, or excessive buildup of dirt and mold.  

Symptoms of a bad drip pan include:

• Water pooling under the refrigerator
• Visible cracks, holes, or warping in the pan
• Mold or mildew growth in the pan
• Unpleasant odors emanating from the refrigerator base

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Fix interior lights that won't turn on or water dispenser issues with this refrigerator door switch. Easy DIY repair with video guide included.

This refrigerator door flipper mullion is the folding center rail that bridges the gap between the doors. It helps complete the door seal and reduces condensation along the center for better temperature retention.

• Bridges the gap between doors to complete the center seal and improve efficiency
• Folds out of the way when a door opens; flips into place as the doors close
• Helps limit moisture/sweating at the middle of the refrigerator
• Replaces a cracked, loose, or broken mullion that causes air leaks, doors popping open, or poor sealing

• Disconnect power before servicing; remove door bins for access
• Remove mounting screws; lift off the assembly and disconnect the harness if equipped
• Transfer any end caps/brackets; ensure spring orientation and proper wire routing during reassembly
• After installation, verify smooth flipping action and a continuous gasket seal down the center

Ice won't dispense or jams in chute? Cracked bin or broken auger blades stop ice flow. This ice bin assembly restores dispensing. Easy DIY, no tools.

The Shaft is an OEM part for Whirlpool refrigerators. This component serves as the axle for the refrigerator's wheels, allowing for smooth movement when repositioning or cleaning the appliance. It is designed to fit securely and ensure stability during use. The shaft's approximate length is 26 inches.

Common causes of a bad wheel shaft include excessive weight, rough handling during relocation, or wear and tear over time.

Symptoms of a bad wheel shaft include:

• Difficulty moving the refrigerator
• Unstable or wobbly positioning
• Visible bending or damage to the shaft
• Unusual noises when moving the appliance

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Ice maker overflowing or not stopping? This shut-off arm extension clips onto the bail arm to help the bin detect when full. Simple 5-minute fix.

This acoustic fiber is the sound-absorbing insulation used in a refrigerator's machine compartment. Replacing a missing or damaged pad reduces operating noise from the compressor area and helps maintain the unit's intended sound levels.

• Absorbs and dampens compressor and condenser fan noise from the rear machine compartment
• Helps reduce vibration resonance transmitted through the cabinet
• Restores sound control when original insulation is torn, saturated, or missing
• Common symptoms: increased humming, buzzing, or rattling from the back or bottom of the refrigerator

• Disconnect power and pull the refrigerator forward for rear access
• Remove the lower rear access panel and note the insulation's placement/orientation
• Position the new pad in the same location; keep clear of coils, wiring, airflow paths, and moving parts
• Reinstall the access panel and restore power; verify no contact or obstruction

Refrigerator not cooling or freezer too warm? A damaged evaporator fan blade stops cold air circulation. This replacement restores airflow. Video guide included.

Creates an airtight seal to keep cold air in and moisture out. Replace when worn or torn to restore cooling performance and prevent frost buildup.

Connects the dispenser motor to the ice bucket auger. Replace if stripped, worn, or broken to restore proper torque transfer and smooth ice dispensing.

The Glass Shelf is an OEM replacement part for Whirlpool refrigerators. It is designed to fit inside the pantry drawer, providing an additional storage surface for organizing and accessing your perishable items.

A bad pantry drawer glass shelf can occur due to accidental breakage, cracks, or wear and tear over time. If you notice symptoms such as a broken or damaged shelf, difficulty in organizing your pantry items, or an unstable storage surface, it may be time to replace the glass shelf.

Symptoms of a bad pantry drawer glass shelf include:

• Broken or damaged shelf
• Difficulty in organizing pantry items
• Unstable storage surface

Restore your refrigerator's pantry drawer by replacing the faulty or damaged glass shelf with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

Measures 30.58" width by 17.78" depth

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal