Kss42db Parts

This ice dispenser chute door assembly opens to release ice and closes to help seal the dispenser opening. It helps limit warm air and moisture from entering the freezer so the chute stays clear and dispensing remains reliable.

• Opens during dispensing and closes to help seal the ice chute
• Helps reduce frost, moisture, and warm air intrusion at the dispenser
• Worn or warped door can stick open/closed or fail to seal
• Common symptoms include frost/ice around the chute, moisture at the dispenser, or clumping in the ice bin

• Unplug the refrigerator before servicing
• Remove the dispenser front panel/cover to access the chute area
• Note the door orientation and any spring/hinge positioning before removal
• After installation, manually cycle the door to confirm smooth movement and proper seal

This refrigerator ice auger sits inside the ice bin and rotates to move cubes or crushed ice toward the chute. Replacing a worn, bent, or stripped auger restores smooth, consistent dispensing performance. What it does:

• Rotates inside the ice bin to feed ice toward the crusher and dispenser chute
• Helps deliver either cubes or crushed ice depending on the selector
• Common symptoms: dispenser motor runs but no ice comes out, weak/intermittent dispensing, frequent ice jams, or grinding noises from the ice bucket

• 1 ice auger

• Unplug the refrigerator before servicing; remove and empty the ice bin
• Note the order of internal parts during disassembly; transfer any reusable hardware from the original assembly
• Wear cut-resistant gloves—metal and plastic edges can be sharp
• Reassemble so the auger turns freely by hand, reinstall the bin, restore power, and test the dispenser

This replacement light bulb restores clear, reliable illumination so you can see contents and monitor appliance operation. Replace a burned-out, dim, or flickering bulb to bring visibility back to the area it lights. What it does:

• Provides illumination in the appliance's interior or designated lighting location
• Makes it easier to see contents and check status at a glance
• Common symptoms: light won't turn on, intermittent/flickering light, dim or blackened bulb

• 1 light bulb

• Disconnect power before servicing; allow hot surfaces and the old bulb to cool completely
• Remove any lens/cover, then remove the old bulb
• Install the new bulb securely without overtightening; reinstall the lens/cover if present
• Restore power and test operation

This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:

• Thread-forming Type AB design engages thin metal or plastic components
• Secures panels, brackets, trim, or covers to reduce looseness and vibration
• Replaces missing, stripped, or corroded fasteners
• Helps maintain alignment for proper operation and reduced noise

• One screw

• Disconnect power before servicing; shut off water supply if working near water lines
• Use the correct driver for the screw head; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking plastic
• Repair damaged holes or replace worn clips/inserts before installing the new screw

• Size: #8-18 x 5/8 in (length 0.625 in)
• Thread type: Type AB, thread-forming

This 8-32 x 5/8 screw replaces missing or damaged hardware specified by the manufacturer to secure panels, brackets, and internal components in your appliance. Restores a tight, rattle-free fit to help prevent vibration and misalignment.

• Provides the correct 8-32 thread and 5/8-inch length where specified
• Secures sheet-metal panels, brackets, and internal assemblies
• Replaces missing, stripped, or corroded screws
• Symptoms include loose or rattling panels, misaligned parts, or hardware that won't stay tight

• Disconnect power; shut off gas before servicing
• Support panels/components while removing or installing hardware
• Start threads by hand to avoid cross-threading; tighten only until snug
• Match the original screw's location and orientation for proper fit

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This refrigerator ice maker assembly automatically freezes water and harvests cubes so you have a steady supply of ice in the freezer. Replacing a failed assembly restores consistent, hands-off ice production.

• Freezes water in the mold and ejects cubes on a controlled cycle
• Signals the water inlet valve to refill after each harvest
• Pauses production when the bin is full via the unit's shutoff mechanism
• Common signs of failure: no ice production, won't eject or refill, intermittent cycling, or very small/hollow cubes

• Unplug the refrigerator and shut off the water supply before servicing
• Take photos of wiring and mounting to match connections and positions during reassembly
• Reuse any model-specific brackets or covers from the original unit if required
• After installation, restore power/water and allow several hours for the first batches

This refrigerator compressor is the heart of the sealed cooling system. It compresses and circulates refrigerant so the fresh food and freezer sections reach and maintain set temperatures, restoring cooling performance when the original unit has failed.

• Compresses and moves refrigerant through the evaporator and condenser to remove heat from the cabinet
• Restores cooling when a failed or seized compressor is the cause of no-cool/weak-cool conditions
• Symptoms include a warm refrigerator or freezer, extended run time with little cooling
• Clicking or humming from the compressor area with no start, or overheating and cycling on overload

• Sealed-system service requires EPA Section 608 certification, recovery equipment, brazing, deep vacuum, and precise recharging
• Disconnect power and properly recover refrigerant before opening the system; replace the filter-drier, braze with nitrogen purge, leak-test, evacuate, then charge to the specification on the model's data plate
• Transfer any model-specific grommets, brackets, tubing, and external inverter/start components from the original unit or replace as directed in the service manual

This defrost bi-metal thermostat senses evaporator temperature during the defrost cycle and opens to stop heater power at the safe cutoff. Replacing a failed thermostat restores reliable defrosting and helps prevent ice buildup that restricts airflow and cooling.

• Monitors evaporator temperature to control the defrost heater
• Closes when cold to allow defrost; opens at cutoff to terminate defrost and prevent overheating
• Helps maintain clear evaporator coils for proper airflow
• Common symptoms: heavy frost on the back wall/evaporator, poor cooling, or defrost heater not energizing

• Disconnect power before servicing; wear cut-resistant gloves
• Access the evaporator; mount the thermostat in the original location with firm contact on the tubing
• Transfer any original clip or insulation as found to ensure proper sensing
• Secure all connections and route wiring away from the heater and moving parts; clear existing ice before restoring power

This ice door motor drives the dispenser flap that opens for ice dispensing and closes to seal the chute. Replacing a weak or failed motor restores smooth door movement and helps prevent warm air and moisture from entering the freezer. What it does:

• Actuates the ice chute door during dispensing and returns it closed for a proper seal
• Helps reduce frost, condensation, and ice clumping around the dispenser
• Can address ice not dispensing due to the door not opening/closing
• May resolve clicking or grinding noises from the dispenser area

• Unplug the refrigerator before servicing; wear cut-resistant gloves
• Remove dispenser trim/control panel to access the ice door assembly; handle wiring carefully
• Note linkage and wire orientation before removal to ensure proper reassembly
• After installation, test the dispenser to verify the door opens/closes and seals the chute

This is the replacement cover for the refrigerator crisper lid. It restores a clean, finished edge and proper lid operation over the crisper bin so drawers open and close smoothly and contents remain covered.

• Replaces a broken or missing cover on the crisper-lid assembly
• Provides a finished surface and correct fit for the lid above the crisper drawer
• Helps prevent the lid from binding, popping off, or failing to close
• Common symptoms: cracked/missing piece, lid misalignment, difficulty opening/closing the crisper

• Disconnect power before servicing
• Remove food and crisper drawer(s) for clearance
• Release any screws or locking tabs, remove the damaged cover, and retain hardware as needed
• Align the new cover and secure it; avoid forcing plastic parts

Color: black. It measures about 10 inches wide by 3 inches deep.

This door bracket connector links the door bracket to its mating linkage in select refrigerator door assemblies. Replacing a worn or broken connector restores a solid connection so the door operates smoothly and stays properly aligned. What it does:

• Couples the door bracket to the hinge/actuator linkage to maintain alignment
• Helps ensure smooth door opening and closing
• Supports proper door sealing to reduce gaps or misalignment
• Replace if cracked, broken, or missing; common symptoms include a loose, clicking, or misaligned door

• Disconnect power before servicing; support the door as needed to prevent strain on hinges
• Remove the relevant bracket/cover to access the connector; note the connector's orientation
• Transfer and reuse existing screws/fasteners
• After installation, check door alignment and gasket contact all around

This light cam assembly interfaces with a switch mechanism to turn the light on when actuated and off when released, restoring reliable lighting performance and preventing the light from staying on. What it does

• Engages the light switch as the mechanism moves to provide on/off control
• Restores consistent interior lighting function
• Helps prevent heat build-up from a light left on
• Typical symptoms: light stays on, won't turn on, intermittent operation, or a broken/missing cam near the switch

• 1 light cam assembly

• Disconnect power before servicing
• Access the switch/cam area; note the original cam's orientation
• Transfer any reusable clips/brackets from the old part if present; avoid forcing brittle plastics
• Restore power and test light operation before full reassembly

These inserts are for 1/4 inch plastic tubing. Package of 4.

This compressor overload is the thermal protector for your refrigerator's compressor. It opens the circuit when the motor overheats or draws excessive current, helping prevent damage and restoring reliable starts when the original protector fails.

• Interrupts power to protect the compressor during overheat or overcurrent conditions
• If failed, symptoms include: compressor won't start, repeated clicking or brief hum then stop, warm refrigerator/freezer, and an unusually hot compressor shell
• A weak protector may trip repeatedly and reset after cooling, causing intermittent cooling
• Works in tandem with the start relay/device to manage compressor startup current

• Disconnect power before servicing and pull the unit forward for rear access
• Remove the rear cover; note wire positions and take a photo for reference
• Pull the old overload straight off the compressor terminal; transfer leads and firmly seat the new overload in the same orientation
• Capacitors can retain a charge—handle with care; reinstall cover and restore power to test