Kudc10fxss25 Parts

This replacement shield fits over the heater/probe area to provide a protective barrier. It helps prevent direct contact and excessive radiant heat exposure, protecting nearby components and supporting accurate temperature sensing for consistent operation. What it does:

• Shields the heating element and adjacent temperature probe/sensor area
• Helps prevent heat damage to nearby plastics, wiring, and components
• Reduces the chance of items contacting or striking the heater/probe
• Common signs it's needed: cracked, warped, or missing shield; discoloration; rattling or an exposed probe/heater area

• 1 shield

• Disconnect power and allow all heated parts to cool before servicing
• Access the heater/probe area and note the original shield orientation
• Seat the shield fully; secure with existing clips/fasteners if applicable
• Verify clearances around the heating element before restoring power

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This compression tube nut secures water inlet tubing to a threaded fitting to create a reliable, leak-resistant seal. Replace a cracked or stripped nut to stop drips at the connection and keep your appliance's water system working properly.

• Compresses the tubing against the fitting to seal the water line at the inlet valve, filter head, or other water-system connections
• Helps correct leaks at the water line connection point
• Replaces nuts that are cracked, cross-threaded, or deformed
• Common symptoms: water dripping at the connection, difficulty tightening the line, or a poor seal after reassembly

• Shut off the water supply and disconnect power before servicing.
• Slide the nut onto the tubing first, seat the tube fully on the fitting, then hand-tighten and snug with a wrench; do not overtighten.
• Inspect and reuse the existing sleeve/ferrule and tube insert if in good condition; replace if worn.
• Restore water and check for leaks at the connection.

The door balance mount is the side-frame bracket that supports the dishwasher's door counterbalance system. When worn or broken, it can let the door drop, slam, bind, or feel heavy. Replacing it restores smooth, controlled door movement. What it does

• Anchors the door springs and balance link/cable to counterbalance the door's weight
• Helps the door open and close smoothly without dropping or slamming
• Guides the balance link for consistent, quiet movement
• Common symptoms: door feels heavy or uneven, falls open, won't stay put, or makes grinding/squeaking noises; visible damage to the bracket or rollers

• One door balance mount (bracket)

• Disconnect power and shut off water before servicing
• Pull the dishwasher out slightly to access the side where the mount is installed
• Carefully relieve spring tension; note link/cable routing before removal
• Transfer the spring/link to the new mount, secure the bracket, and check door balance on both sides

This mount secures the dishwasher's upper spray arm to its water feed, keeping the arm aligned and free to rotate so the upper rack receives consistent spray coverage and dependable cleaning.

• Supports and centers the upper spray arm at the correct connection point
• Helps maintain a solid connection to the feed tube/manifold for proper water delivery
• Wear, cracks, or looseness may lead to poor cleaning on the upper rack, arm wobble, or noise
• Replacing a damaged mount can help restore smooth spray arm rotation and wash performance

• Disconnect power and turn off water supply before servicing
• Pull out the upper rack; remove the upper spray arm from its mount
• Release the old mount's locking tabs or fasteners and remove it from the feed tube/tub
• Install the new mount fully, reattach the spray arm, and verify it spins freely before testing

This upper dishrack assembly restores a solid, organized top rack for cups and bowls and smooth sliding on the rails. Replacing a damaged or rusted rack helps keep items secure and positioned for effective washing.

• Holds and organizes dishes on the upper level of the dishwasher
• Slides on rack rails for easy loading and unloading
• Maintains proper spacing to promote spray coverage
• Replaces racks with broken/missing tines, bent sections, or peeling/rusting coating
• Helps resolve binding, wobbling, or racks that won't stay on the tracks

• Disconnect power to the dishwasher before servicing.
• Pull the rack forward, remove rail end caps/stops, and slide the old rack out.
• Transfer any removable clips or holders from the old rack if needed.
• Place the new rack on the rails, reinstall end caps, and verify smooth travel before restoring power.

This vent door bezel is the trim piece that frames the vent opening on the dishwasher door. It restores a clean, finished look and helps keep the vent assembly properly seated if the original bezel is cracked, loose, or missing.

• Mounts on the exterior of the door around the vent outlet
• Provides a finished edge and helps retain the vent assembly/gasket
• Replaces damaged or missing trim that won't stay attached
• Common symptoms: broken tabs, loose or rattling vent trim, visible gap or cosmetic damage around the vent

• Disconnect power to the appliance; turn off water supply if needed
• Open the door and remove fasteners to access the vent area behind the panel
• Release the old bezel (tabs/screws), align the new bezel, and secure flush to the panel
• Do not overtighten fasteners; avoid vibration or leaks

This inner door seal forms a moisture barrier between the dishwasher tub and the door assembly, helping keep wash water and steam contained. Replacing a worn seal can stop drips at the door and protect internal components.

• Seals the joint along the inner door to contain wash water and steam
• Helps prevent door-area leaks or drips during cycles
• Blocks moisture from entering the door cavity where electrical parts reside
• Common signs: water at the bottom/sides of the door, damp control area, visible wear/flattening or tears on the seal

• Disconnect power and turn off water supply before servicing
• Open the door and remove perimeter screws to separate inner/outer door panels
• Remove the old seal; clean the mounting surface and note seal orientation
• Press the new seal firmly into place, reassemble, and run a leak check

This replacement screw secures appliance components, panels, and brackets. It restores a tight, reliable hold when an original fastener is missing or damaged, helping eliminate rattles, gaps, or shifting parts.

• Fastens two or more parts together inside the appliance
• Helps keep panels, brackets, or trim securely in place
• Can reduce vibration, rattling, or loose handles caused by missing/loose screws
• Replaces worn, stripped, or corroded fasteners

• Disconnect power and shut off water supply before servicing
• Match location and orientation to the original fastener
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to prevent stripping or cracking

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks

12 Ft in length

This cover screw secures an appliance cover or access panel to the cabinet, protecting internal components and reducing vibration. Replace missing, stripped, or corroded screws to keep panels tight and the unit safe and quiet.

• Fastens a cover or access panel to the appliance chassis
• Maintains proper panel alignment and enclosure integrity
• Helps eliminate rattles or buzzing from loose panels
• Typical symptoms: loose/misaligned cover, missing screw, vibration noise

• Disconnect power; for gas/water appliances, shut off supplies before service
• Wear cut-resistant gloves—sheet-metal edges can be sharp
• Align the cover and start the screw by hand to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin metal

Includes two screws, two clamps, and undercounter mounting brackets.

Color: White