Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The Blower Wheel Bearing is an OEM part for LG air conditioners. This bearing supports the blower wheel, ensuring smooth rotation and efficient airflow throughout the unit.
Causes of a bad blower wheel bearing can include wear and tear from regular use, lack of lubrication, or damage from debris or impact.
Symptoms of a bad blower wheel bearing include:
This OEM LG part is also compatible with some Kenmore models.
I do heating and air-conditioning for my profession and knew exactly what was wrong with this but I did not want to pay the high cost of the only supply house that supplies LG equipment. After doing a little research I found it to be much cheaper on here and yes it was the exact part. This unit I am currently installing in my garage, so I had the evaporator side sitting on the ground in my basement. I figured it was a good time to repair what was needed to be repaired. While in the process I... Read more
This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more
This replacement seal restores a tight, leak-resistant barrier between mating parts inside your appliance. Replacing a hardened or damaged seal helps stop seepage and keeps the system operating as designed. What it does:
This was some repair! My SG1000 stackable is over 30 years old and was purchased second hand. I've replaced many parts in the dryer section, but besides a water inlet, this was my first repair to the washer. All of a sudden it started making a terrible noise and was not agitating the clothes. The spin cycle worked fine. I first replaced the two belts on the bottom, but when I removed the old ones I realized they did not look terribly worn and weren't the cause. Many stories on here indicated... Read more
Leg, adjustable (w/nut)
Took off the old parts and replaced with the new parts Read more
The Leveling Leg Pad is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.
Symptoms of a bad Leveling Leg Pad include:
Causes of a failing Leveling Leg Pad can include wear and tear from prolonged use, exposure to moisture, or excessive weight causing deformation. Replacing worn pads helps maintain the appliance's balance and efficiency.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
For the leveling leg order 22003428.
New leveler pads Read more
Water inlet hose for washers and laundry centers. Connects water supply to fill valve. Replace if cracked, leaking, or worn to prevent floor leaks.
I cannot believe this machine still runs. APP has sold me repair parts for this unit now 3 times. First I wanted to replace the old belts. They still worked but was more a preventative thing. Next was a water control valve a few years ago. This time I noticed a leak near the valve again. I decided to buy a new valve and also replace all the rubber hoses that were 35 years old. The repair took about 3 hours. 1.5 to remove the old parts and do a cleaning that was greatly needed. 0.5 hours to... Read more
Size: 90 inches long. To order hose extension use 12001585. To order siphon break use 76660.
Model# MAV7257AWW Maytag Atlantis Washing Machine. Repairs were fairly easy along with the videos appliancepartspros offers on their website. Parts also came with instructions on how to install. Other videos were available on You Tube. The only part difficult to install was Thrust bearing kit - make sure when installing to pull down on shaft so washer and e-clip will fit. Another note, you can get a pulley for your replacement motor pulley on eBay and Maytag.com. Just pay close attention to... Read more
Internal hose that channels water from the washer's outer tub to the drain pump. Replace if cracked, leaking, or worn to prevent puddles under the machine.
Removed front of washing machine, loosened clamps, got wet, replaced hose, tightened clamps, tested hose--no leaks--job done. PLEASE, PLEASE put up a description indicating the length of hose, measured along its length, is 15." It will save other folks wondering if they ordered the wrong item. Thank You. Read more
Seals the agitator shaft opening to prevent leaks and protect internal components. Replace if you see water leaking from the center post during wash cycles.
Found the wonderful parts diagrams you most generously share online and a couple of YouTube videos . I determined it should be repairable. In my cast the agitator shaft was frozen (rusted) in place. I was very fortunate to have been able to eventually remove it with the use of a lot of BP penetrating oil and heat. Long and short the replacement parts fit perfectly and the washer is running like new. Special thanks to the online support make my repair possible. Read more
Seals the water path at the injector assembly. Replace if you notice leaks during fill cycles or poor water flow. Confirm fit with your model number.
Replaced the Injector valve, nozzle and sleeve-in using new hose clamps Read more
This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.
Replace Read more
This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.
Took off cover, installed new parts. Read more
Connects water supply to the dispenser injector in your washer. Replace if cracked, nicked, or leaking. Installs at the top under the lid assembly.
First the parts showed up as promised in 2 days. Injector fill hose wasn't leaking but replaced to be on safe side. Everything went together just like OEM parts. Cost less then having my appliance guy just walk thru the door at $80.00 Read more
This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.
Replaced the tube and the clamp Read more
Hose clamp for securing water supply and drain hoses on the washer. Provides leak-free seal at hose connection points.
Replace faucet adapter, replace fill and drain hose assembly. You must remove outer cabinet to be able to route new hoses and access hose connections under tub. Read more
This injector seal fits the refrigerator's water injector. It restores a tight, watertight/airtight connection where the injector passes through the liner or mates to the fill tube, helping prevent leaks and frost around the opening.
1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more