La9690xww1 Parts

This factory screw secures appliance components such as panels, brackets, and trim. It replaces missing, stripped, or damaged hardware to restore a tight, rattle-free fit and proper alignment in the specified location for your model.

• Fastens covers, panels, brackets, or trim as specified in the parts diagram
• Restores secure fit when an original screw is missing or damaged
• Helps reduce vibration, rattling, and looseness
• Direct-fit hardware specified by the manufacturer for the original location

• Disconnect power and shut off water/gas before servicing
• Verify the screw's location in your model's parts diagram before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver/bit and avoid overtightening into plastic to prevent stripping

This plate-clutch transfers torque from the washer transmission to the tub so the machine can engage and maintain spin cycles. Replacing a worn plate-clutch helps restore reliable spin performance and reduce slipping or shuddering. What it does:

• Engages the transmission to allow the tub/agitation assembly to spin.
• Helps transfer rotational force for normal spin speeds and load control.
• Commonly replaced when the washer slips out of spin, spins slowly, or shudders during the spin cycle.
• Supports proper clutch engagement to prevent intermittent spin failures.

• Disconnect power and water before beginning any repair.
• Access typically requires removing the washer cabinet and/or agitator; basic hand tools are usually sufficient.
• Inspect surrounding components (drive belt, transmission, clutch housing) for wear while replacing this part.

For mating terminal use [AP31136300].

This retaining washer secures a center-mounted component within the assembly, keeping parts aligned and in place during operation. Replacing a worn or missing washer helps prevent looseness, vibration, and noise for more reliable performance. What it does:

• Holds a component on a center shaft or stud to prevent axial movement
• Maintains proper alignment under rotation and load
• Can reduce wobble, rattling, or scraping noises from a shifting assembly
• In applicable washers, can help restore consistent agitation or spin when parts have been moving out of place

• 1 retaining washer

• Disconnect power and water before servicing; wear cut-resistant gloves
• Note the order and orientation of all spacers, washers, and clips during disassembly
• Clean mating surfaces and ensure the washer is fully seated before reassembly
• Inspect adjacent hardware for wear or damage and replace as needed

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

This 12-14 x 1/2 screw is a factory fastener used to secure appliance panels, brackets, and components. Replacing a missing or stripped screw restores a tight fit, reduces rattling, and keeps parts properly aligned for reliable operation.

• Secures panels, brackets, and internal components to their mounting points
• Replaces damaged, rusted, or missing hardware
• Helps stop vibration and rattling caused by loose fasteners
• Restores proper alignment and stability of covers or assemblies

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the original screw's location and length; replace one at a time
• Start threads by hand to prevent cross-threading; tighten snugly without over-torquing
• Reinstall any original washers, clips, or spacers used with the screw

Size: 10-24 x 3/8 inch.

This pin collar is a small retaining fastener that secures a shaft or component in place, preventing lateral movement and keeping assemblies aligned for reliable operation. It's a simple replacement to restore proper fit and function. What it does

• Retains shafts, pins, or small components to prevent sliding or separation
• Helps maintain alignment of moving parts for smooth operation
• Commonly replaced when parts shift, wobble, or fall out of position
• Works as a low-profile mechanical stop in various appliance linkages

• Pin collar (single)

• Disconnect power to the appliance before beginning any repair
• Verify orientation and seating against the mating part; install so collar fully engages the shaft or groove
• Use appropriate tools and avoid hammering or forcing the part to prevent damage
• Reinstall retaining rings or additional hardware in the original order

A small replacement retainer clip that secures panels, trim pieces or small hoses to prevent movement and rattling. Replaces worn or broken clips to restore proper fit and reduce noise from loose parts. What it does

• Secures appliance trim, panels or lightweight components to the cabinet or chassis
• Prevents rattling, vibration noise and misaligned panels caused by a missing or damaged clip
• Holds wiring looms or small hoses in place on select appliance models
• Restores OEM fit where original clip has broken, bent or fallen off

• Disconnect power (and water, if applicable) before servicing the appliance
• Small part — a flat-head screwdriver or needle-nose pliers may be helpful for removal/installation
• Handle sharp edges on panels and wear gloves and eye protection as needed

This screw-washer assembly secures panels, brackets, and other appliance components. The integrated washer spreads load and resists loosening, so replacing a worn or missing fastener restores a tight, reliable fit and helps eliminate rattles.

• Provides fastening with a built-in washer for even clamping and retention
• Replaces missing, stripped, or corroded hardware
• Helps address loose panels/handles and vibration or rattle noises
• Supports proper alignment of covers, brackets, and trim

• Disconnect power and shut off water or gas (as applicable) before servicing
• Match to the original fastener; location and quantity in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten; replace other severely rusted or damaged fasteners in the same area

This adjusting nut threads onto an eyebolt to set and lock an adjustment point. It helps maintain proper tension or alignment in the mechanism so the appliance operates smoothly without the setting drifting over time. What it does:

• Threads onto an eyebolt to fine-tune and secure an adjustment
• Helps prevent vibration from loosening the setting
• Replaces a stripped, rounded, or missing nut so adjustments hold
• Visual cues for replacement include damaged threads or worn hex flats

• 1 adjusting nut

• Disconnect power; turn off water or gas supply if applicable
• Components attached to eyebolts may be under spring or mechanical tension—support and relieve tension before removal
• Mark or measure the original setting to match during reassembly
• Start by hand to avoid cross-threading; tighten securely without over-torquing

Size: 8-32 x 1/2 inch.

This drain hose coupling connects two sections of the washer drain hose to restore a watertight path for wastewater, helping prevent leaks and restore proper draining. What it does:

• Joins two drain hose sections or connects hose to a mating outlet for secure water flow
• Seals the hose connection to reduce leaks at the joint
• Restores proper draining when a damaged or missing coupling causes slow drain or leakage
• Designed to fit the OEM hose profile for a snug, stable connection

• One drain hose coupling as shown

• Turn off power and water supply before starting any repair
• Inspect hose ends for damage; trim to clean cut if required for proper fit
• Push hose ends fully onto the coupling and secure with manufacturer-recommended clamps

A replacement nut and bolt fastener used to secure appliance components and restore proper connection. Helps stop rattling and keeps panels, brackets, or assemblies held firmly in place. What it does

• Secures panels, brackets, or small assemblies to prevent movement and vibration.
• Restores a loose or missing fastener that can cause rattling or misalignment.
• Provides a direct-fit replacement when the original nut or bolt is stripped, worn, or lost.

• Turn off power and unplug the appliance before servicing electrical units.
• Use appropriate hand tools and matched-size sockets/wrenches to avoid rounding heads.
• Replace with the correct torque per manufacturer guidance; do not overtighten.
• If other fasteners are corroded or damaged, inspect and replace as needed.

This replacement bolt is a direct-fit fastener used to secure appliance components. It restores proper fastening to reduce movement and noise while keeping parts aligned for safe operation. What it does

• Secures panels, brackets, or assemblies to prevent loosening and rattling
• Restores proper alignment of mounted components after repair or maintenance
• Helps maintain safe operation by keeping parts firmly attached
• Common symptom: loose or missing bolt causing vibration or parts shifting

• One replacement bolt

• Disconnect power before servicing the appliance to avoid electrical shock
• Use the correct socket or wrench size to avoid stripping the head
• Tighten securely but avoid overtightening to prevent thread damage
• If corrosion or damaged threads are present, replace the mating fastener or insert as needed

This syphon breaker prevents dirty drain water from being siphoned back into the dishwasher, helping maintain proper draining and protect wash water from contamination. It's a direct-replacement drain air-break for compatible dishwashers. What it does:

• Stops backflow/siphoning from the household drain into the dishwasher
• Helps maintain proper drain performance and prevents wastewater re-entry
• Can reduce odors and cloudy or soiled dishes caused by contaminated wash water
• Works as part of the dishwasher's drain plumbing to preserve wash hygiene

• Disconnect power to the appliance and turn off water supply before servicing
• Replace only with identical part and ensure correct hose routing and secure clamps
• Inspect adjacent drain hoses and connections; replace damaged hoses or clamps as needed