Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Seals the top of the outer tub to prevent leaks and splashing. Replace if cracked, worn through, or gasket is compressed causing water to escape onto the floor.
Removed the old tub cover/gasket by removing the front panel and top lid. Then, unclipped the tub cover. Read more
This injector seal fits the refrigerator's water injector. It restores a tight, watertight/airtight connection where the injector passes through the liner or mates to the fill tube, helping prevent leaks and frost around the opening.
1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more
Leaking water at the tub ring during fill? This lower water injector channels incoming water into the tub. Simple 30-minute DIY repair with basic tools.
Simple. Remove top back panel. (4 screws) Remove old injector. (1 nut screw.) Rotate to remove. (Other side is a tab in a slot.) Unsnap the upper injector. Snap upper injector on to new lower injector. Replace in reverse order. Run washer, look for leaks. Read more
Replacement mounting bolt for washer outer tub assembly. Secures tub components together with nut. Replace if rusted, stripped, loose, or missing.
We watched the video before we purchased the parts for this project. We wanted to make sure exactly what parts we would need. Thanks for having this information available. We purchased the mounting stem repair kit,,tub bearing kit, 3 new bolt/washers that hold the outer tub in place and the spanner wrench. Cleaned everything... NOTE :TAKE THE TIME TO CLEAN YOUR FILTERS ON THE BOTTOM. Thing went back together smoothly. We refereed back to the video when in doubt. Total repair $118.00... Read more
This lid bumper cushions the contact point between a washer lid and the top panel to reduce slamming noise and protect the finish. Replacing a worn or missing bumper restores smooth, quiet lid operation and helps prevent paint damage.
Called a Maytag repair man, said "the bumpers are no longer available". These little things are actually critical to operation, because the lid safety switch needs to be pressed back far enough to sense that the lid is closed, and without the bumpers, this is a little iffy. I looked up the parts on the internet, came across AppliancePartsPros.com and guess what, the parts were available !! Ordered, delivered on time, installed, and I'm up and running. Now I don't have to hear my wife... Read more
To order indicator lens use WP22001948.
Replace this washer gasket seal to stop leaks between components. Worn gaskets cause water leakage and poor performance. Verify fit with your model.
We ordered parts from appliance parts pros and I fixed it. Read more
Mounting bolt secures the tub and internal components in your laundry center. Replace if stripped, rusted, or missing to restore stable assembly fit.
Purchased and installed new tub bearing and seals. Decided to replace the tub bolts as well, since I had it apart. Now if I could just find a new outer tub (which the manufacturer has discontinued). Appliance parts pros has a great "how to" video which made it simple! Read more
This is a rubber gasket that sits inside the water inlet hose connection on your washing machine. It creates a watertight seal between the hose fitting and the water supply valve to prevent leaks. Replace this gasket if you notice water dripping from the hose connections at the back of the washer.
Here's the story. All my appliances except the dryer broke. Yeah. talk about bad luck. First I tried to fix the refrigerator. Replaced both motherboard and inverter board. Now it wakes up but the compressor does not kick in. Need another part. The washer, well I have to pull out the sink to get enough room to pull out the washer to fix it. Since the refriigerator is still in the middle of the kitchen, I don't need to tear apart another room. Nevertheless, let me say this, I love my "older"... Read more
Hose washer and plastic insert for inlet hose. To order separately: for washer use WPY013783, for strainer use WP22002960.
Washer won't advance through cycles or gets stuck in one mode? Replace the timer to restore proper wash, rinse, and spin sequencing. 15-30 minute repair.
After the timer quit we had one more load to do so we ran each cycle manually, advancing the timer by hand through the pre-soak, wash, rinse, spin cycles. That told us there were no problems with the other switches. Pulled the back off the control assembly and it was no big deal to get the old timer out. I suggest doing that before you order and comparing the part you are replacing to the images shown online (since there are two timer versions for this model) to make sure you get the right... Read more
Replacement lug stop that limits movement of a mechanical component to prevent over-travel and reduce wear. Restores proper stopping action so doors or internal mechanisms operate more smoothly and safely. What it does:
I emailed appliancepartspros.com with what my problem was and they informed me what was wrong they gave me a part number to order, tools needed and a brief explanation how replace the seal. they also have online video's for different repairs. I watched the video for lip seal(part # 207843) replacement.I also had to remove the brake assembly in order to replace the seal so I watched that video also. I went online and got the part numbers for items I needed to make my repairs.Just follow the... Read more
Replacement mounting screw secures panels, brackets, and trim to the appliance frame. Needed when original screw is stripped, missing, or damaged.
Screw: 8-16 x 3/8 inch.
Fix agitator wobble and excessive vibration with this retaining washer. Secures center-mounted components to prevent looseness and noise during operation.
Not one to patch a job, I ordered all seal kit, bearing kit, new shaft keeper, transmission oil, spanner wrench. I have the newer version of the agitator shaft so it does not have the groove for the internal clip. I Custom ground a thick washer so that as the agitator shaft goes into the transmission it fit flush into the slot for the old style shaft clip. With the plastic keeper in position I marked and pull the shaft. I drilled a hole that would be fit tight against the custom washer and used... Read more
This small spacer washer fits in the washer's drive assembly to set the correct clearance between mating parts. Proper spacing helps components rotate smoothly and quietly while minimizing metal-to-metal contact and premature wear.
Found the wonderful parts diagrams you most generously share online and a couple of YouTube videos . I determined it should be repairable. In my cast the agitator shaft was frozen (rusted) in place. I was very fortunate to have been able to eventually remove it with the use of a lot of BP penetrating oil and heat. Long and short the replacement parts fit perfectly and the washer is running like new. Special thanks to the online support make my repair possible. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.