Lds5811bb Parts

This holder is a small mounting bracket used inside the dishwasher to secure its mating component so it stays aligned and stable during operation. Replacing a cracked or missing holder restores proper support and prevents looseness or rattling.

• Secures an associated interior component in position on the tub, rack, or related assembly
• Maintains alignment to help the component operate smoothly
• Helps prevent vibration, rattling, or parts coming loose during cycles
• Common signs of failure: visible cracks, missing clip, or the attached part won't stay put

• Disconnect power and water supply before servicing; wear cut-resistant gloves
• Open the door and remove any rack or cover needed to access the holder
• Note the original orientation; transfer any reusable screws or clips
• After reassembly, run a short test cycle to verify proper operation

This hinge bracket secures the appliance door to the cabinet and provides a stable pivot point for smooth opening and closing. Replaces a worn or broken bracket to restore proper door alignment and sealing. What it does:

• Supports and locates the door hinge so the door pivots correctly.
• Restores proper door alignment and helps the door close and latch securely.
• Stops sagging, uneven gaps, or scraping caused by a damaged bracket.
• Works as the mounting point for hinge pin hardware.

• One hinge bracket

• Disconnect power (and water supply if applicable) before starting any repair.
• Support the door during removal to prevent it from dropping; two-person lift may be required for heavier doors.
• Retain or reuse original hinge pins, screws, and shims unless replacements are specified.

This holder is a small mounting bracket that secures related components in place, helping maintain proper alignment and quiet operation. It replaces worn or broken holders to restore stable support for the attached part. What it does:

• Secures and supports the associated component to prevent shifting or sagging
• Maintains alignment to help ensure smooth operation and reduce noise
• Worn, cracked, or broken holders can cause rattling, misalignment, or component movement
• Used where a fixed support point is required inside the appliance

• One holder/mounting bracket

• Disconnect power (and water if applicable) before starting any repair
• Remove nearby panels or components as needed for access; keep fasteners for reassembly
• Inspect surrounding clips, screws, and mounting points and replace if damaged

This parts assembly is a direct-replacement assembly used to restore the original mechanical/electrical components it contains so the appliance can operate as designed. It replaces a worn or damaged assembly to help resolve related failures. What it does

• Replaces the factory assembly that houses the appliance's internal components and connections.
• Restores proper component alignment and secure mounting to prevent intermittent faults.
• Addresses symptoms such as failure to operate, unusual noises, loose or damaged internal parts, or intermittent electrical/connectivity issues.
• Works as the factory-specified repair for units showing wear or damage in the affected assembly area.

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock or injury.
• Handle internal components carefully to avoid damage to wiring, connectors, or sensors.
• Follow the OEM service manual and wiring diagrams for correct installation and routing.

A replacement rail assembly that supports the dryer drum and helps maintain smooth, quiet rotation. Restores proper drum alignment and reduces rubbing or scraping sounds when the drum turns. What it does:

• Supports and guides the dryer drum for stable rotation
• Helps prevent drum wobble, friction noises, and uneven wear
• Restores correct drum alignment after rail or support failure
• Can improve noisy operation caused by worn or damaged rails

• One rail assembly

• Disconnect power before beginning repair; for gas dryers also shut off gas supply
• Drum removal is commonly required for access — follow the OEM service instructions
• Inspect adjacent drum glides, rollers, and seals and replace if worn

This frame assembly replaces a damaged or worn front cabinet frame to restore a secure fit and finished appearance. It provides a stable mounting surface for door components and helps maintain proper alignment. What it does:

• Replaces cracked, bent, or cosmetically damaged front frame pieces
• Restores proper fit and alignment for the door and trim
• Helps eliminate gaps that can trap debris or affect door operation
• Provides the original mounting points for associated trim and hardware

• One frame assembly

• Disconnect power and follow appliance-specific safety procedures before servicing
• Handle carefully to avoid scratching or damaging adjacent panels and trim
• Installation typically requires removing door/trim and fastening with existing screws or clips

This hinge assembly secures and pivots a refrigerator or freezer door to ensure proper alignment and smooth opening. Replaces a worn or damaged door hinge to restore stable door movement and a tight seal. What it does:

• Supports the appliance door and provides a pivot point for opening and closing.
• Restores correct door alignment to help maintain an even seal and reduce gaps.
• Reduces sagging, scraping, or uneven movement caused by a worn hinge.
• Works with the cabinet mounting point to keep the door stable during use.

• One hinge assembly

• Turn off power to the appliance and remove stored items from the door before starting.
• Use proper tools and follow OEM instructions or service manual for safe removal and installation.
• Handle glass shelves and door panels carefully; some installations require temporary support of the door.

Color: gray. Measures about 1 inch high by 4 inches deep.

This nozzle guide positions and supports the dishwasher spray nozzle on the rack, helping it align with the rear feed port for reliable water flow to the spray arm and consistent cleaning performance.

• Aligns the rack nozzle with the dishwasher's water feed port
• Stabilizes the nozzle to help ensure steady spray delivery
• If worn or broken, you may notice poor cleaning on the affected rack
• Can also cause intermittent spray or drips at the rear nozzle connection and difficulty engaging the rack nozzle

• Disconnect power and turn off the water supply before servicing
• Pull the rack forward, remove rack end caps/stops, and lift the rack out
• Release the old guide from the nozzle assembly; install the new guide and verify smooth movement and proper alignment with the feed port
• Reinstall the rack, restore power/water, and run a short test to check spray and for leaks

This water guide directs water through the dispenser/ice path so water flows where it should, helping prevent leaks and misdirected dispensing. It's a small molded channel designed to route cold water inside the refrigerator. What it does:

• Guides and channels water from the supply toward the dispenser or ice-making area
• Helps prevent water from dripping into areas it shouldn't and causing puddles
• Supports consistent dispensing by keeping the water path aligned
• Commonly replaced when cracked, warped, or when water is leaking or pooling

• One water guide piece as shown

• Disconnect power and shut off the water supply before replacing
• Remove any interior shelves or panels as needed to access the guide
• Handle carefully to avoid damaging mounting tabs or adjacent seals
• Secure all clips; test dispenser and check for leaks after installation