Lse806aee Parts

This agitator seal assembly sits at the agitator/drive-shaft pass-through to keep wash water inside the tub and away from the drive system. Replacing a worn seal helps stop center-post leaks and protects internal components from moisture.

• Seals the opening where the agitator/drive shaft passes through the tub or centerpost
• Helps prevent water from migrating into the centerpost/gearcase area
• Supports reliable agitation and spin by keeping contaminants out of the drive assembly
• Common symptoms of failure: water leaking from the center of the tub or beneath the washer, or rust/water tracks around the agitator hub

• Disconnect power and shut off water; wear gloves and eye protection
• Remove agitator cap and fastener, then lift the agitator to access the seal (procedure varies by model)
• Note the original seal orientation; clean mating surfaces and install the new seal squarely (lightly lubricate only if specified by the manufacturer)
• Reassemble and run a short fill/agitate test while observing for leaks

This internal hose connects the washer's outer tub to the drain pump, channeling wash water during the drain cycle. Replacing a worn or leaking hose helps prevent puddles and supports reliable draining performance.

• Routes water from the outer tub to the drain pump inside the washer
• Maintains a sealed path; cracks or loose connections can lead to leaks
• Visible splits, soft spots, swelling, or aging can cause water under the unit
• Obstructions or internal collapse may contribute to slow or incomplete draining

• Disconnect power and turn off water supply before servicing
• Expect residual water; use towels or a pan when removing the old hose
• Note hose routing and clamp positions; seat fully on each port and secure with appropriate clamps
• Run a quick fill/drain test and check all connections for leaks after installation

This terminal insulator assembly isolates and supports an electrical connection where it passes through the appliance chassis. Replacing a cracked or heat-damaged insulator helps prevent shorts and restores a safe, reliable connection.

• Electrically insulates a live terminal from the metal cabinet or oven wall
• Provides a secure pass-through/mounting point for the element/wire connection
• Helps prevent arcing, shorting, and localized heat damage at the connection
• Typical symptoms: visible cracks or burn marks on the insulator, tripped breaker, intermittent or no heat due to a compromised connection

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the terminal area; label or photograph wiring to ensure correct reassembly
• Transfer wires one at a time; reuse existing hardware if serviceable and tighten connections securely
• Inspect nearby wire ends/connectors and replace any that are heat-damaged or brittle

The Lamp Cover is an OEM part for LG ranges. This part is responsible for covering and protecting the indicator light on the range console. It ensures that the indicator light is properly shielded, allowing for clear visibility and easy identification of the selected settings or functions.

A bad lens cover can occur due to damage, discoloration, or wear over time. If you notice symptoms such as a cracked or missing lens cover, diminished visibility of the indicator light, or difficulty in determining the status of the range, it may be time to replace the lens cover.

Symptoms of a bad lens cover include:

• Cracked or missing lens cover
• Diminished visibility of the indicator light
• Difficulty in determining the status of the range

Restore the function and aesthetic appeal of your LG range by replacing the damaged or worn-out lens cover with this genuine OEM part.

This LG replacement part is also compatible with Sears/Kenmore models.
 

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

For complete assembly order WP206680.

This tub cover and gasket seal the top of the outer tub to contain splashing and prevent leaks during wash and spin. Replacing a cracked cover or compressed gasket restores a tight rim seal and cleaner operation. What it does:

• Creates a watertight seal at the outer tub rim
• Helps reduce splash-over and directs incoming water flow
• Helps keep clothing and debris out of the gap between basket and outer tub
• Common symptoms: leaks from the top/front, visible cracks in the ring, or a brittle/torn gasket

• One tub cover and one perimeter gasket

• Disconnect power and turn off the water supply before servicing
• Access the tub area; release retaining clips/screws and detach any inlet/flume from the old cover
• Clean the tub rim thoroughly; seat the new gasket evenly and install the cover without pinching the seal
• Reuse existing fasteners/clips; ensure the cover is fully latched all around and do not overtighten

This 6-foot dryer vent duct connects your dryer's exhaust outlet to the wall vent. It provides a secure path for moist air to exit the home, helping maintain airflow and consistent drying performance. What it does:

• Vents hot, moist air from the dryer to the exterior
• Replaces crushed, torn, or lint-clogged ducting
• Helps address longer dry times, heat buildup/shut-offs, or moisture and lint around the dryer
• Supports a short, direct run to reduce kinks and airflow restrictions

• One 6-foot dryer vent duct

• Disconnect power; for gas models, turn off the gas supply before starting
• Pull the dryer forward and remove old ducting and lint/debris from connections
• Attach the duct fully to the dryer outlet and wall vent and secure with clamps; avoid sharp bends or crushing
• Move the dryer back carefully and confirm strong airflow at the exterior vent hood

This mechanical washer timer controls the sequence and duration of wash, rinse, and spin cycles. Replacing a worn timer restores proper cycle advancement and consistent operation when the washer stalls, skips steps, or only progresses when the knob is turned.

• Controls and sequences power to the drive motor, water inlet valves, and drain pump per the selected cycle
• Advances the machine through fill, agitate, drain, rinse, and spin intervals
• Provides internal contacts that start/stop each step and signal the next stage
• Common symptoms: no cycle advance, stopping mid-cycle, intermittent operation, or advancing only when manually turned

• Disconnect power before servicing; do not work on a live appliance
• Access the control console; remove the panel/cover to reach the timer
• Photograph and transfer wires one at a time to matching terminals to avoid miswiring
• Mount the new timer securely and align the shaft with the knob/dial before reassembly

This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.

• Applies clamping force around a hose to hold it on a barb or stub fitting
• Commonly used on washer drain and tub-to-pump hose connections
• Helps stop drips at the joint and prevents the hose from slipping off
• Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band

• Unplug the appliance and turn off water supply; expect some residual water
• Seat the hose fully on the fitting; place the clamp just behind the bead/barb
• Tighten until snug and secure; do not overtighten to avoid damaging the hose
• Run a short test cycle and recheck for leaks at the connection

This motor clip secures a motor to its mounting bracket or housing, keeping it aligned and stable during operation. Replacing a bent, broken, or missing clip helps stop rattling and prevents the motor from shifting. What it does:

• Retains the motor on its mounting bracket or frame
• Helps maintain alignment to reduce vibration and noise
• Prevents movement that can cause rubbing or wire strain
• Direct replacement when the original clip is damaged or missing

• One motor clip

• Disconnect power before servicing; allow all moving parts to stop
• Access the motor area, note the clip's orientation, and remove the damaged clip
• Seat the motor fully, then install the new clip to secure it to the bracket
• Inspect related mounts/grommets and wiring for wear; verify clearances before restoring power

The Oven Knob Assembly is an OEM replacement part for LG electric and gas ranges and wall ovens. It houses the temperature control dial along with mounting provisions. 

Symptoms of failure include:

• Dials that cannot be turned smoothly to desired settings   
• Loose or wobbly knobs detracting from precise control
• Impossible to fasten securely due to damaged mounting tabs

Common causes relate to wear from prolonged, repeated use over many cooking cycles. Adjustments stress mounting tabs until failure. Excess cleaning solutions further corrode metal connections.  

This authentic LG knob assembly is compatible with select Kenmore-branded appliances.

The Heating Element is an OEM part for LG electric ranges. It serves a critical cooking function by using electric current to generate heat energy that cooks food inside the oven cavity. The heating element is constructed from flame-resistant and durable materials precisely designed to withstand high temperatures in a clean efficient manner.  

Causes of a bad heating element can include mineral deposits on coils, cracks from overheating, or general wear over extended use.

Replacing a faulty element restores dependable oven performance. 

Symptoms of a bad element include:

• Inefficient or uneven cooking temperatures
• Longer baking and cooking times 
• Cracking or sagging coils affecting heat output
• Potential safety issues if damage exposes live wires

This element also fits the heating designs used in Jenn-Air and Frigidaire electric ovens.

This bolt is a genuine Whirlpool part, sold individually. It can be used as a replacement part for a washing machine or a washer/dryer combination appliance. This bolt fastens parts to one another in conjunction with a nut so that they do not come loose while the washing machine vibrates when it is in operation.A bolt might be easily lost or misplaced as it is a small part that might go missing without any noticeable symptoms. Additionally, a bolt might be stripped through general wear and tear or as a result of a direct impact collision with a hard object that warps the component beyond functionality. If any of these things occur, the bolt should be replaced by this genuine OEM replacement part.This is an OEM part sourced directly from the manufacturer. It is sold individually. This bolt is compatible with the following appliance brands: Whirlpool, Maytag, International, and Jenn Air.

This lid bumper cushions the contact point between a washer lid and the top panel to reduce slamming noise and protect the finish. Replacing a worn or missing bumper restores smooth, quiet lid operation and helps prevent paint damage.

• Provides a soft stop between the lid and top to minimize noise and vibration
• Helps prevent chips, scratches, and rust where the lid meets the cabinet
• Maintains proper lid spacing for a solid, rattle-free close
• Common signs it's needed: missing/flattened bumper, louder closing, rattling, or visible wear at contact points

• Disconnect power before servicing
• Open the lid, remove the old bumper, and clean the mounting area
• Seat the new bumper fully in the mounting location as designed
• Open/close the lid to ensure quiet, secure contact

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation