Lsg7304aae Parts

This 12-14 x 1/2 screw is a factory fastener used to secure appliance panels, brackets, and components. Replacing a missing or stripped screw restores a tight fit, reduces rattling, and keeps parts properly aligned for reliable operation.

• Secures panels, brackets, and internal components to their mounting points
• Replaces damaged, rusted, or missing hardware
• Helps stop vibration and rattling caused by loose fasteners
• Restores proper alignment and stability of covers or assemblies

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the original screw's location and length; replace one at a time
• Start threads by hand to prevent cross-threading; tighten snugly without over-torquing
• Reinstall any original washers, clips, or spacers used with the screw

This factory screw secures appliance components such as panels, brackets, and trim. It replaces missing, stripped, or damaged hardware to restore a tight, rattle-free fit and proper alignment in the specified location for your model.

• Fastens covers, panels, brackets, or trim as specified in the parts diagram
• Restores secure fit when an original screw is missing or damaged
• Helps reduce vibration, rattling, and looseness
• Direct-fit hardware specified by the manufacturer for the original location

• Disconnect power and shut off water/gas before servicing
• Verify the screw's location in your model's parts diagram before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver/bit and avoid overtightening into plastic to prevent stripping

Pop rivet secures sheet-metal panels, brackets, and burner jar lids on appliances. Replace missing, drilled-out, or damaged rivets for permanent hold.

This lower plastic collar is a small retainer that keeps mating components aligned and secure within the assembly. Replacing a worn or broken collar restores proper fit, reduces play, and helps prevent rubbing or noise during operation. What it does:

• Acts as a keeper/retainer to hold parts in position on a shaft or hinge point
• Maintains spacing and alignment between moving components
• Helps reduce wobble, scraping, or squeaking caused by excess play
• Replaces collars that are cracked, deformed, or missing

• 1 lower plastic collar

• Disconnect power and, if applicable, shut off water before servicing
• Support the assembly to relieve load before removing the old collar
• Match the original orientation; press/seat the new collar fully and evenly
• After reassembly, check for proper alignment and smooth, quiet operation

Size: 10-32

Dryer won't start or respond to controls? This electronic control board manages cycle timing and user settings. Restores normal operation when failed.

Size: 8-32 x 1/2 inch.

Washer won't start or stops mid-cycle? This lid position switch detects when the lid is open or closed, restoring safe operation. Moderate DIY repair.

This adjusting nut threads onto an eyebolt to set and lock an adjustment point. It helps maintain proper tension or alignment in the mechanism so the appliance operates smoothly without the setting drifting over time. What it does:

• Threads onto an eyebolt to fine-tune and secure an adjustment
• Helps prevent vibration from loosening the setting
• Replaces a stripped, rounded, or missing nut so adjustments hold
• Visual cues for replacement include damaged threads or worn hex flats

• 1 adjusting nut

• Disconnect power; turn off water or gas supply if applicable
• Components attached to eyebolts may be under spring or mechanical tension—support and relieve tension before removal
• Mark or measure the original setting to match during reassembly
• Start by hand to avoid cross-threading; tighten securely without over-torquing

A small replacement retainer clip that secures panels, trim pieces or small hoses to prevent movement and rattling. Replaces worn or broken clips to restore proper fit and reduce noise from loose parts. What it does

• Secures appliance trim, panels or lightweight components to the cabinet or chassis
• Prevents rattling, vibration noise and misaligned panels caused by a missing or damaged clip
• Holds wiring looms or small hoses in place on select appliance models
• Restores OEM fit where original clip has broken, bent or fallen off

• Disconnect power (and water, if applicable) before servicing the appliance
• Small part — a flat-head screwdriver or needle-nose pliers may be helpful for removal/installation
• Handle sharp edges on panels and wear gloves and eye protection as needed

Fix a dryer that won't shut off or advance cycles with this dryer timer replacement. Controls cycle duration and sequence. Easy DIY repair for most users.

This pin collar is a small retaining fastener that secures a shaft or component in place, preventing lateral movement and keeping assemblies aligned for reliable operation. It's a simple replacement to restore proper fit and function. What it does

• Retains shafts, pins, or small components to prevent sliding or separation
• Helps maintain alignment of moving parts for smooth operation
• Commonly replaced when parts shift, wobble, or fall out of position
• Works as a low-profile mechanical stop in various appliance linkages

• Pin collar (single)

• Disconnect power to the appliance before beginning any repair
• Verify orientation and seating against the mating part; install so collar fully engages the shaft or groove
• Use appropriate tools and avoid hammering or forcing the part to prevent damage
• Reinstall retaining rings or additional hardware in the original order

This idler pulley guides and maintains tension on the dryer drive belt to help the drum rotate smoothly. Replacing a worn pulley restores correct belt tracking and reduces noise from rubbing or slipping. What it does

• Guides the dryer drive belt and keeps proper belt tension
• Helps the drum turn smoothly during normal operation
• Commonly used when you hear squeaking, grinding, or belt slipping noises
• Prevents premature belt wear and misalignment

• One idler pulley

• Disconnect power before starting any repair; the appliance is de-energized
• Basic hand tools required; remove the front or access panel and drum as needed per your model's service instructions
• Inspect the belt and bearing surfaces; replace belt if damaged or glazed
• Do not lubricate the pulley unless the OEM specifically directs it; replace if bearing is noisy or seized

Replacement 3/8-16 nut that secures bolts and threaded shafts in appliance assemblies. Needed when original nut is stripped, lost, or corroded.

Burner won't adjust heat or jumps to full power? This infinite switch restores variable temperature control to surface burners. DIY install in 30 minutes.

This replacement screw fastens appliance panels, brackets, and components. Use it to replace missing, stripped, or rusted hardware to restore a secure fit and help reduce vibration or rattling during operation.

• Secures panels, brackets, and internal components to the cabinet or frame
• Helps prevent vibration, rattling, and misalignment from loose hardware
• Replaces a missing, rusted, or stripped original screw
• Matches the original fastener style for proper fit in specified locations

• Disconnect power; shut off gas and water supplies before servicing
• Use the correct screwdriver or nut driver and match length/thread to the original
• Start threads by hand to avoid cross-threading; do not overtighten, especially into plastic or thin metal