Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
If your washer agitator spins freely or won't move clothes, the upper agitator may be worn. Often replaced with agitator dogs. Video guide available.
I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more
This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.
Replaced 2 springs and brackets. Also replace rear legs and front legs and re leveled. Works fine. Read more
This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.
I ordered two replacement baffles and screws, then lifted the top of the dryer to access the drum and installed the two new baffles. Read more
This 1-1/8 in wire retaining ring locks into a groove to secure components in place. It helps prevent parts from sliding off a shaft or shifting out of position so assemblies stay aligned and operate reliably.
Based on recommendation to replace the clutch if clothes aren't spinning dry enough, I ordered a new clutch. Upon disassembly, I observed no Ring Wire/C-Clip and that the bearing appeared worn. Where did the clip go? Well, the bearing wore down such that it wore out the clip and bearing up to the sleeve of the shaft. Knocked out the old bearing, tapped in the new and was done. I disassembled the brake shoes but believe you can get the bearing in and out without doing so. Not a bad job, just... Read more
10 - 16 x 1/2
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair... Read more
If your washer agitator spins freely or clothes tangle around it, the splines may be stripped. This center post assembly restores wash action. 15-min DIY.
My wife noticed that our washing machine was making a terrible rumbling noise and seemed to be out of balance all of the time. She was on the verge of calling a repairman when I said I wanted to look at it first. I noticed the agitator was very loose and would spin in your hand. I removed 1 bolt and the agitator was out. The teeth in the agitator were stripped out so by simply ordering a new agitator and installing it I turned a $250.00 repair call into a $70.00 DIY fix. Thanks. Read more
Specs: 10-16 x 1/2 inch.
After shopping for a new Whirlpool Thin Twin Stack, Found appliance parts pros online and decided to take it apart to see if repair was a possibility. APPro's online instructions were easy to follow, in a couple hours it was apart, and I placed the order. Reg ground took a week from NY, so the laundry piled up that week. The parts arrived on Monday morrning, by afternoon the machine was running like new! The cause was the belt tensioner pulley had frozen. Replaced it, drum wheels,snap... Read more
Replacement timer knob for washers. Installs on the control panel to operate the timer dial. Order if your original knob is cracked, broken, or missing.
I ordered a new timer knob from Appliance Parts. The knob came, and I went to my washer and screwed it on. That took about 35 seconds. Everything is fine now! Read more
Fix a washer that hums but won't agitate or spin with a new drive motor. Common when motor is weak, seized, or trips the breaker. 90-minute DIY repair.
My Kenmore washer had three problems and thanks to AppliancePartsPros.com videos I was able to repair all three. The washer coupler was defective so I replaced it. This topok about 30 minutes. The washer lid switch was defective. This took about an hour. Finally, the motor was defective. I was able to disconnect the motor from the transmission and test the motor by leaving the wiring connected and run a wash cycle. The motor was dead. I replaced it with a new motor and now the washer runs... Read more
Washer thrust ring acts as a bearing spacer between the outer tub and basket drive, controlling end-play and reducing friction. Replace when worn to restore smooth, quiet operation and prevent premature wear.
Purchased parts from your site and did a self repair. Excellent quality , speedy delivery and easy to install. Now our 13 year old washer works as good as new. Read more
Rubber grommet for motor mount stud.
Replaced dog ears. Read more
If your washer stops mid-cycle or won't advance to rinse or spin, the timer may have failed. This mechanical control sequences wash cycles reliably.
Watched the repair video from AppliancePartsPros, Ordered parts, installed it. Washer works. No problem. Easy parts, good price, outstanding service. Been a repeat customer many times over. Read more
Inner tub basket holds clothing during wash cycles. Replace if cracked, rusty, or broken. Installs in center of washer between outer tub and agitator.
Ordered the parts from AppliancePartsPros - super fast shipping, and even though I opted for regular shipping all of my parts arrived the very next day, including the big and bulky inner basket. Disassembly went smoothly, simply following the directions in the AppliancePartsPros video. The only problem I had was that the inner basket simply would NOT come of the drive block no matter what I did. Struggled for a few hours trying to take it off. Then, I called AppliancePartsPros and they said it... Read more
This adapter tube assembly connects sections of the appliance's water line to create a secure, leak-resistant path for water flow. Replace it if the tube is cracked or the connection no longer seals properly to prevent leaks and restore flow.
Ordered a replacement valve and installed it. The part from AppliancePartsPro was an exact replacement for the original part. Replaced the hot and cold hoses at the same time to insure no leaks. Cold water settings now work properly again. Read more
Replacement power cord that connects your washer to the wall outlet. Includes strain relief for cable protection. Needed when original cord is damaged, pinched, shorted, or worn. Direct plug-in installation.
Bought a new cord and removed the back of the washer and unclipped the old and clipped in the new. 5 minutes tops. Read more
Replaces the upper tub ring that mounts on top of the outer tub as a splash guard. Order a new ring if yours is cracked, broken, or no longer securely attached.
This was the second attempt at fixing this problem. The first repair and parts were generated by listing the problem and reviewing the potential corrections, listed on the web site. From making repairs on other clothes washers, I was confident that some of those potential causes could have been the cause. Unfortunately the counterbalance spring and suspension springs were not the cause as they were attached as intended and in good condition. I reached out for Appliance Parts Pros input... Read more