Lte6234vq2 Parts

This fixed-value resistor is an electrical component used in select dryers to limit current in a specific control circuit. It helps the timer or electronic control operate correctly by dropping voltage to safe, design-intended levels.

• Provides precise resistance to reduce voltage/current in the designated dryer circuit
• Supports proper operation of the timer, control board, or end-of-cycle signal (varies by model)
• Failure may present as a timer that won't advance, an inoperative signal/buzzer, or irregular cycle behavior
• Replace if visibly burned/damaged or if testing shows an open or shorted condition

• Disconnect power to the appliance before servicing
• Access the console/wiring harness and note original wire routing
• Make secure, insulated connections and route the resistor/leads exactly as original to avoid heat or chafing
• After installation, run a test cycle to ensure proper operation of the affected function

This screw and washer is an OEM replacement part used for Whirlpool washers. It is used to secure the lid switch. Each screw is sold individually. The screw measures approximately 1 inch.

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

This agitator drive shaft sits inside the washer's gearcase and transfers motion to the agitator. Replacing a worn or stripped shaft restores firm engagement and reliable wash action while helping reduce slip and grinding during agitation.

• Transfers oscillating motion from the transmission to the agitator
• Provides the splined interface that engages the agitator/coupler
• Common symptoms include no agitation, intermittent/slipping agitation, or grinding/clicking from the gearcase
• Visible wear, rounded splines, or a bent shaft can lead to a loose or non-moving agitator

• Disconnect power and water; use proper PPE
• Requires removing the cabinet and gearcase; drain and reseal the gearcase per service procedures
• Keep gears, spacers, and clips in order; reassemble in the original orientation
• Inspect mating parts (agitator coupler/splines, drive block, seals) and replace if worn

Used for lid switch.

This rear foot assembly supports the back of the appliance and helps keep it level. Replacing a worn or missing foot restores stability, reduces vibration, and helps prevent the unit from rocking or "walking."

• Supports the rear of the cabinet and maintains proper height
• Provides a stable contact point with the floor for accurate leveling
• Helps reduce vibration, rattling, and movement during operation
• Common signs of failure: rocking/wobbling, excessive vibration, noise from the base, or a visibly worn/missing foot

• Disconnect power before servicing; if applicable, shut off water supply
• Protect the floor and carefully tilt or lay the appliance back with assistance
• Remove the old rear foot and install the new assembly per your model's instructions
• Set the unit back in place, level it, and verify stability

This replacement dispenser stores your dishwasher's detergent and rinse aid, then releases them at the proper time in the cycle. Restore consistent cleaning performance and help prevent leaks around the dispenser area with a fresh assembly. What it does

• Holds detergent and rinse aid; times their release during the wash cycle
• Seals to the inner door to help prevent leaks from the dispenser opening
• Common symptoms: detergent cup won't latch or open, detergent left after cycle, rinse aid not dispensing, leaking around the dispenser, broken latch/cover

• One dispenser assembly

• Disconnect power and water supply before servicing
• Open the door and remove the inner door panel to access the dispenser
• Transfer the wire connector(s); seat the gasket evenly and tighten mounting screws without overtightening
• Reassemble, restore power/water, and run a test cycle to check for proper operation and leaks

This lid hinge pad fits between the washer lid hinge and the cabinet. It cushions the joint to reduce squeaks and metal wear, helping keep the lid aligned and operating smoothly.

• Provides a protective wear surface between the hinge and cabinet/lid
• Reduces squeaks, creaks, and rattling when opening or closing the lid
• Helps maintain proper lid alignment and smooth movement
• Common signs it's worn or missing: squeaking lid, rubbing/scuff marks at the hinge, loose or wobbly lid

• Disconnect power to the washer before servicing
• Support the lid to relieve hinge tension and access the hinge area per your model
• Remove the worn pad and press the new pad fully into the hinge location
• Test lid operation; inspect the opposite hinge and replace its pad as needed if your model uses two

This anti-rattle clip adds light spring tension to keep a small component snug and quiet during operation. Replacing a bent or missing clip helps reduce vibration noise and maintains a secure fit of the attached part.

• Applies tension to prevent rattling and buzzing during use
• Helps keep the mounted piece properly seated and aligned
• Common symptoms of failure: audible rattle, loose/wobbly component, missing or deformed clip
• Simple, drop-in replacement where the original clip is used

• Disconnect power to the appliance before servicing
• Note the original clip's orientation; transfer the new clip the same way
• Use needle-nose pliers for placement; avoid over-bending the clip
• The component is secure and clears adjacent parts before reassembly

This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.

• Supports and centers the spin basket on the tub centerpost/drive shaft
• Provides a low-friction bearing surface to reduce wear and noise
• Helps maintain basket alignment and stability during spin
• When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin

• Disconnect power and water supply before servicing; use proper PPE
• Access typically requires removing the agitator, inner basket, and related drive components
• Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
• Seat the bearing fully and verify smooth basket rotation before reassembly

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

Restore smooth, accurate cycle selection with this replacement timer knob for your dryer. When the original knob is cracked, stripped, or missing, this part lets you reliably set the timer and choose drying programs again. What it does:

• Attaches to the timer shaft so you can set drying cycles and time
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps resolve issues like the knob spinning freely or not turning the timer
• Provides a clean, factory look in white

• 1 white timer knob

• Disconnect power to the dryer before servicing
• Pull the old knob straight off the timer shaft; use steady, even pressure if tight
• Align the new knob with the keyed shaft and press firmly until fully seated
• The pointer aligns with the control panel cycle markings before use

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This agitator mover is the upper auger section of a dual-action agitator. It ratchets in one direction to drive clothes downward for proper turnover, helping restore effective wash action when the original mover is worn or damaged. What it does:

• Creates the one-way, ratcheting motion of the agitator's upper section
• Helps circulate and roll laundry downward for thorough turnover
• Common symptoms of failure: weak agitation, top auger not advancing, clicking/slipping sounds, or visible cracks/stripped splines
• Needed after damage from overloading or long-term wear

• 1 agitator mover (upper auger)

• Disconnect power and turn off water before servicing
• Remove the fabric softener dispenser and agitator cap; take out the center retainer/bolt to access the mover
• Lift off the old mover and seat the new mover fully on the agitator
• Reinstall the retainer/bolt and cap; verify smooth ratcheting action before use