Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
White timer knob insert cap that fits over the timer control knob on your dryer's control panel. Replace if cracked, broken, worn, or missing.
It's working now Read more
Prevents oil leaks from the transmission area. Replace if you see oil puddles under your washer. Confirm fit with your model number before ordering.
I had a lot of problems removing the spin hub, I had to use an air impact wrench to un screw it even then it was very hard, it did not go easy with the hammer & pipe wrench as shown in the video. It was also very hard to remove the bottom spin bearing I had to cut the bearing retainer with a dremel tool so I could get my puller on it. After I struggled to get it apart The repair went very easy, I used brake spring pliers to remove the springs it worked like a charm. I am very pleased with... Read more
Fixes washer leaking during drain cycle. This tub to pump hose connects the tub to the drain pump. Simple 3-minute DIY repair with basic tools.
My husband is a natural handyman, I call him Bob the Builder (don't tell him I told you that!). When our washer started leaking we started looking for a used one online, when that didn't work he figured he'd take it apart and see if he could find the problem himself. Well after doing some research online we replaced the drain pump, which in the long run was a good idea because ours wasn't in very good condition, but our washer still leaked. So after some more looking around he found a hole on... Read more
Washer won't agitate or spin after opening the lid? A faulty lid cam prevents the switch from engaging. Easy 15-minute DIY fix restores operation.
I replaced the switch, the plunger, plunger guide and the lid cam, but the cam still didn't turn on the switch. Turned out someone had stood on the washer and bent the lid slightly, not enough to notice, but since I had ruled out just about everything else I started looking at the lid itself. I ended up bending it back close to it's original shape and now it works fine. I guess I learned a few things about washing machines though. One lesson is when you pull off the controls, the hose leading... Read more
Washer won't spin or stops mid-cycle? A faulty lid switch prevents operation when the lid is bumped or opened. Simple snap-in replacement restores cycles.
I had removed three screws behind the control board cover of the washer, to access the old lid switch. I checked the continuety of the of the switch with a multimeter and it obviously failed the the test by displaying infinity of <1, rather than being 0. I removed the old switch with a flathead screw driver, I tested the new one and installed it in no time. Problem solved!!! Read more
Fix a loose or broken agitator that floats to the top or comes apart during wash cycles. Simple DIY repair—just one screw. Takes under 5 minutes.
I replaced the entire agitator (my appliance agitator could only be replaced in one part not the upper part only). It was super easy but one thing....the video on the website was not helpful because my maytag washer is older and does NOT have a screw down inside the agitator but has one 1/4 inch hex nut on the side down by the base. Good for me though because all I had to do was unscrew the nut, put the new agitator on, tighten the new nut and DONE!! Read more
Broken agitator fins or loose upper agitator? This complete assembly restores proper wash action. DIY-friendly 5-10 minute repair with our video guide.
By watching your video and following the instructions Read more
This 8-18 x 5/8-inch screw secures dryer panels, brackets, and covers. Replace missing or stripped fasteners to restore a tight fit and stability.
I put all pieces that I ordered on the dryer and plugged it in. Read more
Rubber inlet hose that connects your washer to the water supply. Replace if cracked, leaking, or worn. Standard 5-foot length with included washers.
Replaced flow meter and control valve Read more
Replace your dryer's broken, cracked, or missing timer knob. This control knob installs on the timer shaft to set drying cycles and time settings.
Replaced timer Read more
Fix a washer that won't start when the lid is closed with this lid switch plunger. Simple DIY repair—just remove two screws and realign. Video included.
Replace your cracked or missing timer knob cap to restore control panel appearance. Simple 5-minute DIY fix. Chrome finish includes locking pin design.
Watched the video and in 5 mins I was all done, very easy. Read more
Washer won't start or spin? A cracked plunger guide tube prevents the lid switch from engaging. This tube realigns the plunger for reliable operation.
Replace your washer's drain hose if cracked, kinked, or leaking. This 90-inch hose connects the washer tub to your home's drain system. Sold individually.
Model# MAV7257AWW Maytag Atlantis Washing Machine. Repairs were fairly easy along with the videos appliancepartspros offers on their website. Parts also came with instructions on how to install. Other videos were available on You Tube. The only part difficult to install was Thrust bearing kit - make sure when installing to pull down on shaft so washer and e-clip will fit. Another note, you can get a pulley for your replacement motor pulley on eBay and Maytag.com. Just pay close attention to... Read more
Replace your range indicator lens when cracked or clouded to restore control panel visibility. Clips into place for easy installation. Confirm fit with your model.
Got good advice. Parts in two days. To and running in an hour. Read more
Fix a washer that won't advance cycles, stops mid-cycle, or hums but won't spin. This mechanical timer controls wash sequences. DIY-friendly repair.
Appliance Parts Pros I've used in the past and will continue to use, now they have a video showing step by step how to change the part your going to purchase, video also explains what the part does and symptoms of bad existing parts like mine. Washer machine was dripping water into tank when not in use, it was the water inlet valve. I purchased on a Sunday and it arrived with our mailman on Wednesday. I watched the repair video one more time and changed it out. When you unhook hoses to remove... Read more