Mav7700aww Serial Parts

A snap-style hose clamp that secures flexible appliance hoses to fittings to help maintain a leak-free connection. Simple, durable replacement for a lost or worn hose clip to keep hoses seated and stable. What it does

• Secures a flexible hose to a nipple or barb to help prevent accidental disconnection
• Helps maintain a tight connection that reduces risk of leaks at the hose joint
• Commonly used on drain, fill, or internal circulation hoses where a small snap clamp is required
• Small, low-profile design fits in tight spaces and resists shifting under normal use

• One snap-style hose clamp

• Disconnect power and shut off water supply before beginning any repair
• Access may require removing panels or disassembling interior components depending on appliance
• Pry open or compress the clip as needed with pliers to remove and reinstall; ensure hose is fully seated on the fitting before securing
• Inspect the hose and fitting for damage; replace hose if cracked or degraded

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

This tub-to-pump hose connects the washer's outer tub to the drain pump, carrying water out of the machine during the drain cycle. Replacing a cracked or clogged hose can help stop leaks and restore consistent draining.

• Connects the washer's outer tub to the drain pump
• Transfers wash water to the pump during drain cycles
• A damaged or obstructed hose may cause leaks under the machine or slow/no draining
• Visible splits, soft spots, or kinks indicate the hose should be replaced

• Disconnect power and turn off water supply; protect the area with towels or a shallow pan
• Access the pump area; note hose routing and clamp positions before removal
• Inspect and clear the tub outlet and pump inlet; seat the new hose fully and secure with clamps
• Run a brief fill/drain test and check carefully for leaks before reassembly

This brake spring restores proper tension in the washer's transmission brake so the basket stops promptly and releases cleanly for spin. Replacing a fatigued or broken spring helps bring back smooth, reliable spin and stopping performance.

• Maintains brake tension to hold the basket stationary between cycles
• Releases the brake during spin so the basket can reach proper speed
• Helps stop the basket smoothly at cycle end
• Common signs include no/slow spin, basket coasting too long after spin, or brake squeal/grinding when stopping

• Disconnect power and water before servicing; wear gloves and eye protection.
• The brake spring is under tension—secure the assembly and carefully relieve spring force before removal.
• Access typically requires removing drive components to reach the brake assembly; support the washer safely if tilted.
• After installation, hand-rotate the drive pulley to ensure smooth brake engagement and release before running a test cycle.

This hinge bushing is the low-friction sleeve the hinge pin pivots in. Replacing a worn bushing restores smooth, quiet door or lid movement, keeps alignment true, and helps the appliance close cleanly while reducing hinge wear.

• Provides a smooth pivot surface between the hinge pin and bracket
• Helps maintain alignment so the door or lid closes flush
• Reduces squeaking, grinding, or binding when opening/closing
• Replaces cracked, flattened, or missing bushing that can cause sagging or scraping

• Disconnect power (and water supply if applicable) before servicing.
• Support the door or lid before removing hinge fasteners; note the order of spacers/washers.
• Remove the worn bushing, seat the new bushing fully, and reassemble in the same orientation.
• Inspect the hinge pin and bracket for wear; replace related parts if they are damaged.

Mounting screw used to secure panels, trim, brackets, and small appliance components. Replace a missing or damaged fastener to restore proper fit, reduce vibration, and keep parts aligned for safe operation. What it does:

• Secures panels, control boards, brackets, and trim to maintain correct assembly
• Replaces stripped, broken, or missing screws that cause loose or rattling parts
• Helps prevent misalignment that can interfere with doors, knobs, or covers
• Standard fastener interface — use the correct driver and size for a secure fit

• Disconnect power and/or gas and follow appliance safety procedures before servicing
• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until secure to avoid damage to threads or surrounding parts
• If threads are damaged, replace the mating component or use the correct thread-repair method

Analog water temperature control board.

This locknut is a small threaded retaining nut used to secure rotating and stationary appliance components, helping keep assemblies tight and stable during operation. It prevents parts from loosening and reduces vibration-related issues. What it does:

• Secures shafts, pulleys, or fittings to prevent axial movement
• Keeps assemblies fastened under normal vibration and load
• Helps stop wobble, grinding, or part separation caused by a loose connection
• Works with the matching threaded stud, shaft, or fitting for a proper hold

• Disconnect power and follow appliance safety procedures before servicing
• Use the matching thread size and engage threads fully; hand-start before tightening
• Tighten securely without overtightening; use the correct driver or socket for the nut
• Inspect mating threads and replace if damaged

Spesc: #12 pozi - drive