We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Maintains proper spacing and alignment in your dryer's belt path. Replace if you hear squeaking or notice belt tracking issues. Verify fit with your model.
I replaced the motor and all other moving components along with the felt drum seals.drum glides and drive belt. The wiring instruction is where i had the most problems. Because my wiring had only 4 wires in the harness not 5, and one was a different color then the instructions call out, I believe was because it might have been and older model. the instruction called for a gray wire but mine was white with a blue piggy back wire attached. but after finding a few videos on line i figured that the... Read more
Dryer not heating or flame goes out after a minute? This gas valve with coils restores heat. 15-minute repair with video guidance available.
Replaced valve had some trouble removing the fitting from the valve as the new fitting was slightly too large and had to be replaced with the fitting from the old valve. Used a large crescent wrench to grip the valve at the base and I was able to apply enough force to remove both fittings transferring old fitting to new valve. The instructions were detailed and excellent. The dryer is up and running fine. Read more
Dryer won't heat or flame cycles on and off? A warped burner assembly prevents reliable ignition. Moderate DIY repair restores even drying.
When I first looked at my dryer I thought it was my ignitor, on a closer look I found that about an inch of my burner assembly arm was laying in a corroded mess on the bottom pan of my dryer. I came online and found your website. After reviewing your parts I thought well I can probably get those local and with competive pricing. Wrong!! There are 3 appliance parts stores withing about 3 miles and I checked them all. Higher prices by 25-35% and longer wait times than your advertised... Read more
Seals blower housing to prevent air leaks and lint escape. Replace when you notice lint buildup in your home or reduced drying efficiency. Confirm fit with your model number.
Took the front panel off (the door front), disconnected the connector to the door switch and used a wooden clothespin to bypass the door switch. Turned on the dryer to locate loud squeaking sound and found it was coming from the motor area. When I started to take the blower section apart from the motor, that is when I saw the "blower wheel" slipped off the motor shaft. The blower wheel has a "C" clip retainer and compression ring to keep it snug on the motor shaft (but it was loose). Now I... Read more
This Kit includes the Regulator Lock Limiter, the Main Orifice Spud and the instruction sheet.
By putting on the part. Read more
This is a metal clip that secures the drive motor in place within the dryer cabinet. It clamps around the motor housing to prevent movement during operation. Replace this clip if it is broken, missing, or bent, which can cause the motor to shift and create excessive vibration, rattling noises, or belt misalignment.
Ultimately is was discovered and caused by the blower wheel shaft opening was cracked and broken. Replaced blower fan wheel. Read more
This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:
I was looking for a parts sight and found yours. I started to watch all the video tutorials on each part and the "check these connections first video". Well by doing this I was able to find the source of my problem. What I thought was the heating coil not working right, ended up being the timer that was bad!!! I am so very happy with your sight and the step by step videos that were the success to being able to do this on my own. Read more
Specs: No.8X1/2 HEX WASHER HEAD
Replaced the control board after removing the inner door liner, plastice board cover and board itself, by removing screws, working various plastic clips/tabs and unclipping wire harnesses from board. most of time was spent cleaning the black soot from the door, which had a terrible burnt electrical/plastic fire smell. Cleaned mold/scale off of as much of the door as I could while in there as well. Removing parts without breaking plastic tabs to hold the new parts was trickiest part. Read more
Screw: 8-16 x 3/8 inch.
Dryer won't start or respond to controls? This electronic control board manages cycle timing and user settings. Restores normal operation when failed.
Replacement 3/8-16 nut that secures bolts and threaded shafts in appliance assemblies. Needed when original nut is stripped, lost, or corroded.
Weekend laundry became very noisy, our 1987 Whirlpool washer began doing a dance across the floor and the drum was banging into the inner cabinet. After doing some research and watching a few videos on Appliance parts pros website. I inspected the washer and noticed one leg the rubber coating disintegrated, decided to change all four legs, springs and lid switch. Hardest part of the job is getting the cabinet together. Ops check good. Read more
One of three coils, to get all three order 12001348
I ohm metered the sensors to determine which one was bad (open) Looked up the part on the parts drawing. Ordered part and had the dryer running 2 days later Read more
Replace worn, stripped, or missing 8-18 x 3/8 machine screws that secure control panels, trim pieces, and brackets on your appliance. Restores tight fit.
Appliance won't start or trips breaker? This ground screw secures the grounding conductor to the chassis for safe electrical connection. Simple fix.
I ordered a new heating element and two other parts that attached to the heating element. I discovered a wire that broke off which caused the element not to work so I had to put a new female splicer on the broken wire then replaced the element and reattached the wires and everything worked. Read more
Size: 8-32 x 1/4 inch.
Replaced switch assembly Read more