Whirlpool WP33002793 Dryer Gas Burner Assembly OEM Part

When I first looked at my dryer I thought it was my ignitor, on a closer look I found that about an inch of my burner assembly arm was laying in a corroded mess on the bottom pan of my dryer. I came online and found your website. After reviewing your parts I thought well I can probably get those local and with competive pricing. Wrong!! There are 3 appliance parts stores withing about 3 miles and I checked them all. Higher prices by 25-35% and longer wait times than your advertised delivery times. Came home and ordered my part on Saturday night, parts were shipped on Monday am at my door on Tues afternoon. Very easy install much easier than your video my dryer is 30 years old. Every repairman who has been here has said this model is simple and very long lasting worth repairing. Problem tube did not solve the problem and I shattered my brand new ignitor when it dropped about 1/4 inch on the arm to the top of the dryer..my old ignitor looked good so on it went. Since my problem was not resolved I stewed and came on and talked online to first Danny who walked me through testing my sensors and when they came up reading ok Brent brought up the gas coils as the probable cause and I ordered them. I also told Brent about my igniter issue and after getting some additional info another was on its way and 1 day later in my hands. My older dryer version I popped the front laid on the floor reached in and had the coils replaced and the dryer running 15 minutes later. Guys are great..they make this work for a novice like myself. prices and delivery make it a winning combination. The appliance people could probably take some lessons. Keep up the good work and Thanks. Oh yeah no service call so my parts delivery was less than a call!!

Burned out burner assembly distorted flame so much as to heat up the high limit thermostat safety switch to the off position. Replaced both burner and switch. Very easy and fast (under 15 minutes). Hardest and most time consuming part was finding the 2 hidden screws that held the front panel on the dryer. Once found, only a one minute job to remove panel. No one on youtube apparently had encountered this model of dryer before ( 1990's Maytag). Easy fix and under $80. Good"how to" video.

Replaced it

After bypassing and or testing several parts on the machine, I noticed that the burner tube was sending part of the flame to the top of the flame tunnel where a high limit thermostat was located. By removing and examining the burner tube, I noticed a crack at the end of it. Which allowed part of the flame to curl up in the wrong direction. Thus the high limit thermostat was doing it's job and shutting down the gas valve. Replacing the burner assembly fixed the problem.

After establishing with a voltmeter that the controls - timer, cycle thermostat, and high limit thermostat - seemed to be in good order, I replaced the gas valve solenoid coils. Only two screws to remove to get the front panel complete with door off the DG309 (don't even need to disconnect the door switch!) leaving easy access to the gas valve and burner. Some care required to seat the new o-rings properly and not to lose too much of the chassis wiring when stripping insulation for the new connections, but a pretty simple and straightforward installation. Dryer lit right up and the burner cycled properly again. BUT as an amateur repairman I didn't recognize how badly the burner had eroded over the (37!) years and after three or four loads the burner nozzle simply fell off its mounting bracket. With the new part in hand it was plain to see how much of the original had rotted away, finally eating up the spot-welds holding the burner assembly together. Again, a mere minute or two to get the front of the machine off. Unplug the igniter, one screw off to remove the assembled igniter & burner, one screw off and on to swap the igniter to the new burner, and the one screw back in to reinstall the assembly. Again accessible, quick and easy, but take care not to knock the flat igniter blade against anything in the process - it's fragile! Lit right up and now drying again like the workhorse it's been for decades