Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replace cracked, broken, or missing upper rack wheels that cause the top rack to slide poorly or fall off the rail. Includes roller and axle assembly.
Found the parts I needed on the Appliance Parts Pros website. Went to my local appliance store with the pictures from the website, and they did not agree that the replacement rack roller was what I needed. I was to return with a picture of my Dishwasher upper rack to show them. This was a 30 mile round trip, that I was going to have to do again before the parts I needed would even be ordered. Came home, went back to Appliance Parts Pros website and ordered the 2 items I needed. They... Read more
Routes wastewater from your dishwasher pump to the home drain. Replace if cracked, kinked, punctured, or worn to restore proper drainage and prevent leaks.
Replaced the seal at the Air/Water inlet and also replaced the drain hose. Drain hose had a worn spot due to vibration rubbing on the floor Read more
Specs: No.8X1/2 HEX WASHER HEAD
Replaced the control board after removing the inner door liner, plastice board cover and board itself, by removing screws, working various plastic clips/tabs and unclipping wire harnesses from board. most of time was spent cleaning the black soot from the door, which had a terrible burnt electrical/plastic fire smell. Cleaned mold/scale off of as much of the door as I could while in there as well. Removing parts without breaking plastic tabs to hold the new parts was trickiest part. Read more
Screw: 8-16 x 3/8 inch.
Secures the upper rack rail to prevent it from sliding out. Replace if missing, broken, or popped off. Installs on the end of the rack track.
I installed a new Rack Track and Rack Stop. I watched the short tutorials on your web site for installing each part and voila...the upper rack in my dishwasher was like new...so easy, this 67 year old grandmother could do it with no help from her husband! Read more
Secures the upper spray arm so it spins freely and stays aligned. Replace if cracked, worn, or causing wobble to restore proper water distribution.
Spun each of the three wash arms by hand. All could be made to touch/scrape but the top one was super wabbly. Ordered both the arm and clip. Repair took less than a minute. Used a screwdriver to pry loose one side of the old clip to remove. Aligned the new parts and easily snapped into place. Read more
Replace the cable bracket guide roller on your dishwasher. This small wheel guides the door cable smoothly through the bracket, preventing binding and wear.
Secures your dishwasher to surrounding cabinetry. Replace this bracket if it's bent, broken, or missing to restore a tight, level installation.
Followed video instructions Read more
Replacement leveling leg that stabilizes and adjusts your dishwasher height for proper alignment. Needed when bent, broken, or missing to eliminate rocking.
Fix a dishwasher that won't start or respond to buttons. This electronic control board restores cycle selection and timing. Moderate DIY repair.
Control buttons acting erratic or not responding? This dishwasher control panel vent seal blocks moisture and dust that cause button failure. Easy install.
Push buttons are membrane-type. The wiring inside the membrane corrodes over time (and heat and moisture) until it just doesn't work at all. The membrane is integrated with the top plastic panel - not separately replaceable. Replaced the control panel that's on the top of the door. Easy to fix! Only gotcha is that you have to take off the cover of the control box (inside the door) and slide the locking bar out on the connector for the ribbon cable - the cable doesn't just push in, you have... Read more
Foam insulation liner that installs behind the dishwasher toe kick panel. Replace if torn, compressed, missing, or damaged to restore cabinet insulation.
This flexible injector hose routes liquid between the appliance's injector/dispenser and the pump or spray assembly, restoring proper dispensing and preventing leaks. It's a direct-replacement service part for affected injector connections. What it does
Replaced the injector hose Read more
Water fill hose for dishwashers. Connects water supply to the tub inlet valve. Replace if cracked, leaking, kinked, or damaged to restore proper fill.
Replace your dishwasher's spring adjustment bracket if cracked, bent, or missing. This structural component secures the spring mechanism inside your unit.
This kit includes a 10-foot braided fill hose used to connect a dishwasher's water inlet to the household water supply. It provides a reliable, leak-resistant connection during new installations or when replacing a damaged supply line. Replace this hose if you notice water leaking at the connection point, visible cracks, or bulging in the existing hose.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.