Mdbh949awb Parts

This replacement part is a dishwasher pump and motor assembly. The dishwasher pump and pump motor circulate water through the dishwasher's spray arm. When the spray arms aren't spraying properly, this could mean that it's time for a new pump and motor assembly. Luckily replacing this part is a relatively simple process.Start by making sure the dishwasher is unplugged. After that shut off the water supply going to the dishwasher. Then disconnect the drain line from the garbage disposal or sink drain. Open the dishwasher door and pull out the bottom dish rack. Remove the upper dishrack from its track. Release the spray arm on the bottom of the washer. Then proceed to release the feed tube clips. Using a nut driver remove the bottom access panel and tow panel. Pull them out to remove them. Remove the power cable from the junction box, and disconnect the supply line from the inlet valve. Proceed to pull the dishwasher out of the counter. Tilt the dishwasher on its side and pull the hose from the drain pump. Remove the wire harness from the pump. Disconnect wires from diverter motor and circulation motor. Once complete, proceed to tilt the dishwasher upright and remove the pump and motor assembly from the bottom of the dishwasher. Replace with the new assembly.This replacement part is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dishwashers.

This factory-spec screw secures panels and components in your appliance. Replacing a missing or stripped fastener restores a tight, rattle-free fit so parts stay aligned and operate as designed.

• Fastens brackets, panels, and internal components to their mounting points
• Maintains alignment and reduces vibration during operation
• Replaces missing, worn, rusted, or stripped hardware
• Helpful when you notice rattling, loose panels, gaps, or parts shifting out of position

• Disconnect power; shut off water or gas supply if applicable
• Align the part being secured and remove any damaged hardware
• Hand-start threads to avoid cross-threading; tighten with the correct driver
• Do not overtighten; verify the assembly is secure and operates freely

This replacement shield fits over the heater/probe area to provide a protective barrier. It helps prevent direct contact and excessive radiant heat exposure, protecting nearby components and supporting accurate temperature sensing for consistent operation. What it does:

• Shields the heating element and adjacent temperature probe/sensor area
• Helps prevent heat damage to nearby plastics, wiring, and components
• Reduces the chance of items contacting or striking the heater/probe
• Common signs it's needed: cracked, warped, or missing shield; discoloration; rattling or an exposed probe/heater area

• 1 shield

• Disconnect power and allow all heated parts to cool before servicing
• Access the heater/probe area and note the original shield orientation
• Seat the shield fully; secure with existing clips/fasteners if applicable
• Verify clearances around the heating element before restoring power

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This heater support holds the heating element securely in place inside the appliance, maintaining correct alignment and clearance for reliable operation. Replacing a worn or broken support helps prevent sagging, noise, or damage from an out-of-position element.

• Secures the heating element to its mounting point to keep it stable
• Maintains proper spacing from nearby components and surfaces
• Helps reduce vibration, rubbing, or rattling noises
• Replace if the original support is cracked, warped, missing, or the element appears misaligned

• Disconnect power to the appliance before servicing; allow hot components to cool
• Access the heater per your model's service information; note the original orientation and routing
• Seat the support fully and handle element leads carefully to avoid damage

Bushing, Door spring

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Replace a missing or cracked rinse aid cap to stop leaks and restore proper dispensing. This dishwasher dispenser cap seals the rinse aid reservoir so dishes dry better and avoid spots by delivering rinse aid consistently.

• Seals the rinse aid reservoir to prevent leaks and evaporation
• Helps ensure correct rinse aid dosing during wash cycles
• Replaces worn, stripped, or missing caps that won't tighten
• Common symptoms: pooled rinse aid in the door or tub, visible cap damage, dishes left with spots due to no rinse aid

• For safety, disconnect power to the dishwasher before servicing
• Open the door and remove the old cap by turning counterclockwise
• Clean the dispenser opening; seat the new cap and turn clockwise until snug—do not overtighten
• Refill rinse aid, wipe up any spills, and run a short cycle to check for leaks

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

12 Ft in length

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks

This cover screw secures an appliance cover or access panel to the cabinet, protecting internal components and reducing vibration. Replace missing, stripped, or corroded screws to keep panels tight and the unit safe and quiet.

• Fastens a cover or access panel to the appliance chassis
• Maintains proper panel alignment and enclosure integrity
• Helps eliminate rattles or buzzing from loose panels
• Typical symptoms: loose/misaligned cover, missing screw, vibration noise

• Disconnect power; for gas/water appliances, shut off supplies before service
• Wear cut-resistant gloves—sheet-metal edges can be sharp
• Align the cover and start the screw by hand to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin metal

This is the lower access panel for the appliance's base. It finishes the front opening and shields internal components, helping reduce noise and keep dust and debris away from the motor and wiring.

• Covers the lower service opening beneath the door to provide a clean, finished look
• Helps protect internal components from debris and accidental contact
• Can reduce vibration noise when properly secured
• Replace if the panel is bent, cracked, rusted, missing, or rattles/doesn't stay secured

• Disconnect power; also shut off the water supply
• Support the existing panel while removing mounting screws; retain hardware for reuse
• Position the new panel, align with mounting holes/slots, and reinstall screws—do not overtighten
• Confirm door clearance and that the panel sits flush without interference

Located between the console and door

Includes two screws, two clamps, and undercounter mounting brackets.

This active vent assembly controls airflow from the dishwasher during and after a cycle, releasing humid air at the right time for better drying. Replacing a faulty vent can reduce lingering moisture and steam escaping from the door.

• Regulates and directs moist air out of the tub during the dry portion of the cycle
• Closes during wash to help contain water and heat inside the dishwasher
• Helps reduce interior condensation and improve overall drying results
• Common failure symptoms: dishes not drying, moisture remaining after the cycle, steam escaping at the top of the door, or unusual noise from the vent area

• Disconnect power at the breaker before servicing; allow the unit to cool
• Access is typically through the inner door panel; retain and reuse mounting hardware as required
• Inspect and correctly seat the vent seal to prevent steam leaks
• After installation, run a test cycle to check for proper vent operation and sealing