We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Dryer making loud noise or won't dry? A cracked or loose blower wheel often causes poor airflow. Moderate DIY repair, 1-2 hours with basic tools.
I disassembled my dryer and found that the fan(blower wheel) was "free-spinning" on the motor shaft. A common problem with this model Maytag dryer. I also discovered that the right drum roller (drum support roller) was in the process of failing. Note: the fan drive was frozen on the motor shaft, this was the threaded type of motor and fan assembly. I was able to remove the fan drive by using vice-grip pliers, hammer and a combination wrench to hold motor from turning. Also Note: the fan... Read more
This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.
Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy Read more
Gas smell during or after cycles? Dryer won't heat? Replace the gas valve assembly to restore proper gas flow and safe operation. Advanced repair.
Frigidaire Gallery gas dryer from maybe 15 years ago. Based on the fact the the smell was only in the dryer, I concluded it must be the gas valve failing to completely seal when closed. After looking at the insides again, I suppose it is possible that it was a connection near the burner, but that stuff had remained untouched for 10 years so I still think I made a good assumption. I got a new ignitor as well since I was in there, and compared to the valve, it was cheap! I thought I could get in... Read more
Fix a dryer that won't heat or overheats with a new thermistor. This temperature sensor ensures accurate heating cycles. DIY repair in 30 minutes.
Installed a new thermistor tempiture control and it heats up as it should. Tools used was a ohlm meter, 1" stiff puty knife, #2 Philips screw driver, neadle nose pliers,1/4 & 5/16 nut drivers. Read more
This kit replaces a temperature-control thermostat and its mounting plate in select dryers. It helps restore accurate heat regulation and consistent cycling, protecting against overheating and poor drying results when the original thermostat or bracket has failed.
After verifying the no heat problem myself, I just googled "LG3412W no heat" with my smartphone and thumb. One of the first hits was the Appliance Parts Pros website with a list of 8 possible parts that might fix this problem, listed in descending order of likelihood of success. With 3 adults worth of dirty laundry piling up and straining our ability to drip dry, I had to agonize over: 1) buying a new dryer from whatever a local dealer had in stock, then clearing years of valuable junk in... Read more
The Screw is an OEM part for Whirlpool refrigerators. This screw secures the refrigerator door hinge in place, allowing the door operates smoothly and seals properly.
Over time, screws can become loose or go missing during repairs or adjustments, which can lead to a misaligned door, compromised sealing, and increased energy consumption.
Symptoms of a bad screw include:
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
As soon as the parts arrived, installed them seamlessly. Thank you. Read more
This Kit includes the Regulator Lock Limiter, the Main Orifice Spud and the instruction sheet.
By putting on the part. Read more
This is a metal clip that secures the drive motor in place within the dryer cabinet. It clamps around the motor housing to prevent movement during operation. Replace this clip if it is broken, missing, or bent, which can cause the motor to shift and create excessive vibration, rattling noises, or belt misalignment.
Dryer quit working on a Saturday night. Ordered parts Sunday and they arrived Wednesday installed Thursday afternoon all parts fit perfectly and the dryer runs quietly. Positive experience. Read more
Fix a dryer that won't start, advance, or shut off properly. This timer controls cycle sequencing and duration. Moderate DIY repair, 30-60 minutes.
I had watched the repair video before the part came, it looked easy peasy, so I pulled the wires off the old timer, before noticing that my dryer didn't have the nice wire harness. All wires are clearly marked but 1. I had to search on the internet to make sure where to put it, extending the time of an easy install. Take a picture of your wiring BEFORE pulling everything apart, for reference. Read more
This dryer blower housing encloses the blower wheel and directs air from the drum through the lint filter to the exhaust vent. Replacing a damaged housing restores proper airflow for consistent drying and helps keep lint contained within the airflow path.
This timer with a built-in chime controls cycle sequencing and provides an audible end-of-cycle signal so the appliance finishes and alerts you when a cycle is complete. It replaces a failed or silent control timer. What it does:
Remove front door, front cover and drum, checked all the wires to and from the heater core including those attached to the fan housing and had full continuity through all components including fuses, temp controls, heater coil, etc, checked input for 220 volt and it was OK Ordered the timer and installed and it worked just fine, I think there should be a simple test that could be done on the timer to verify that this function is no longer working I would be happy to send you the old one... Read more
This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.
Googled the problem, watched videos on Youtube. Took apart machine and tried cleaning filter most people said was the problem. Wasn't anything but a penny in it so that wasn't the problem. I decided the pump must be bad ,the spring for the bellows and the console were broken so I bought those as well. Got the parts put them on and machine filled up with water turned over a few times and then stopped. The only thing else it could be is the fill level sensor or the main circuit board. Ordered... Read more
Color: gray. The back part of the knob measures about an inch in diameter, and the front part with the handle is about 2 inches in diameter.
Replaced it Read more
Replacement bracket screw for securing internal panels and brackets to your appliance frame. Needed when original screws are stripped, corroded, or missing.
Specs: No.8X1/2 HEX WASHER HEAD
Replaced the control board after removing the inner door liner, plastice board cover and board itself, by removing screws, working various plastic clips/tabs and unclipping wire harnesses from board. most of time was spent cleaning the black soot from the door, which had a terrible burnt electrical/plastic fire smell. Cleaned mold/scale off of as much of the door as I could while in there as well. Removing parts without breaking plastic tabs to hold the new parts was trickiest part. Read more
Burner orifice that meters gas flow to your dryer's burner. Replace if clogged, damaged, or wrong size for fuel type during LP/natural gas conversion.