Med6100dc0 Parts

This broken belt switch monitors drive belt tension and cuts power to the motor if the belt snaps or slips. Replacing a faulty switch restores proper start/run operation and maintains the dryer's built-in safety shutoff. What it does:

• Monitors belt tension through the idler mechanism
• Opens the motor circuit if the belt is broken or loses tension
• Helps prevent the motor from running when the drum isn't turning
• Failure symptoms include: dryer won't start, stops soon after pressing Start, or no motor sound while controls have power

• Includes 1 broken belt switch

• Disconnect power; turn off gas supply for gas models
• Access the switch near the belt/idler area; many models require removing the front panel and drum
• Note wire locations; move connectors to the new switch and secure in the original orientation
• Inspect belt and idler for wear; ensure correct belt routing/tension before reassembly

This thermal cut-off (TML) is a temperature safety device that opens the circuit if overheating is detected, protecting components from heat damage. Replace a failed or tripped cut-off to restore safe, reliable operation.

• Monitors temperature at its mounting point and interrupts power at a preset limit
• Helps prevent overheating damage to components and wiring
• Typical symptoms include no power, shutting off during use, or no heat—depending on where it's installed
• Can be tested with a multimeter; an open (no continuity) reading indicates replacement is needed

• Disconnect power before servicing; some appliances (e.g., microwaves) can store dangerous high voltage—use proper discharge procedures
• Replace with the same type/rating and mount in the same location/orientation as the original
• Ensure solid contact with the sensing surface and clear airflow/venting to prevent repeat overheating
• Do not bypass thermal safety devices; verify proper operation after installation

The Dryer Door Hinge Assembly is an OEM part for Whirlpool electric and gas dryers. As a critical component, this assembly supports the dryer door and allows for smooth opening and closing. 

Causes of failure include frequent use, which causes hinge components like bushings and bearings to wear out more quickly over time. Housing cracks or mechanical loosening from repeated operation are other issues.

Symptoms of a faulty door hinge assembly include: 

• Door that won't stay closed securely or slams shut on its own   
• Difficulty smoothly opening and closing the door
• Excessive gaps around the edges that allow lint to escape

This genuine Whirlpool replacement fits Maytag, Amana, Jenn-Air, Magic Chef, and select Kenmore dryers.

This replacement seal restores a tight barrier at its mounting point in your appliance. It helps prevent leaks and maintains performance by ensuring a proper fit between connected components where fluids or air must be contained. Location varies by model.

• Creates a reliable seal between mating parts to contain water or air
• Helps stop drips, seepage, and unwanted airflow that can affect performance
• Replace if cracked, flattened, swollen, or leaking
• Common symptoms: moisture under/around unit, residue, or diminished efficiency
• Direct-fit replacement to match the original part's size and profile

• Disconnect power and, if applicable, shut off water supply before servicing
• Note the original seal's orientation; clean and dry all sealing surfaces
• Lightly moisten or use only manufacturer-approved lubricant; avoid petroleum products unless directed
• Seat evenly without twisting; after reassembly, run a test cycle and check for leaks

This high-limit thermostat is a temperature safety switch for the heating circuit. It opens the circuit if temperatures climb too high, helping protect the appliance and restore safe, reliable heating performance.

• Monitors temperature and interrupts power to the heater when a limit is exceeded
• Helps prevent overheating that can damage components or trip other safeties
• If failed open: heater won't energize; cycles may run long or never reach target temperature
• If stuck closed: unit may overheat or shut down as other safety devices trip

• Disconnect power at the breaker before servicing; allow the appliance to cool completely
• Access the thermostat at the heater/temperature control area as designed for your model
• Note wire positions and transfer one at a time; ensure tight, secure connections
• After replacement, inspect the heater and controls for issues that could cause overheating

This in the male piece on the front panel. For the female piece on the door order WPW10111905.

This flat support washer provides a stable bearing surface under a fastener. Its 1-1/2-in diameter helps distribute load, maintain spacing, and keep components aligned so hardware stays tight and assemblies operate smoothly. What it does:

• Distributes clamping force to prevent pull-through and gouging
• Maintains proper spacing and alignment between mating parts
• Helps reduce vibration, rubbing, or wobble from a loose assembly
• Replaces a cracked, deformed, or missing support washer

• One support washer

• Disconnect power and shut off water/gas before servicing.
• Note the order and orientation of any washers/spacers during disassembly.
• Inspect mating hardware and surfaces; replace any worn or damaged parts.
• Tighten fasteners to manufacturer specifications—do not over-tighten.

Includes two bumpers and two locking clips. You will use one or the other depending on hole size.

This flexible, narrow brush reaches under and behind the cabinet to sweep dust and lint from condenser coils and vents. Cleaning built-up debris helps restore airflow and support proper cooling performance.

• Sweeps dust, lint, and pet hair from condenser coils and ventilation areas
• Flexible reach helps access coils beneath or behind the appliance
• Aids proper heat dissipation by clearing airflow paths
• Helpful when coils are visibly dirty, cooling seems weak, or the unit runs longer than usual

• Unplug or disconnect power before cleaning
• Remove the toe grille or rear access panel if needed to access coils
• Brush gently along the coil fins; avoid bending fins or damaging tubing
• Vacuum or wipe up loosened debris before replacing any panels and restoring power

This is the stirrer motor assembly that drives the metal stirrer in the microwave's waveguide. A working stirrer helps distribute microwave energy more evenly, reducing hot and cold spots for consistent heating.

• Rotates the mode stirrer to spread RF energy inside the cavity
• Symptoms of a failing motor can include uneven heating, cold spots, buzzing or grinding from the waveguide area, or the stirrer not turning
• May restore even cooking performance when the original motor is worn or seized

• Unplug the appliance before servicing; high-voltage components in microwaves can retain a dangerous charge
• Remove the grill/cover and access panel to reach the stirrer motor location
• Transfer any mounting hardware from the original part if not supplied
• Ensure the stirrer blade or coupler is correctly seated and turns freely before reassembly

This air duct collar channels dryer exhaust to the external vent connection. It provides a secure, sealed outlet for the vent hose to help maintain proper airflow, reduce leaks, and support consistent drying performance.

• Directs exhaust air from the blower/outlet to the rear vent connection
• Provides a stable connection point for the vent hose
• Helps maintain airflow and drying efficiency
• Common symptoms: vent hose won't stay attached, heat or lint leakage at the back of the dryer, longer dry times, visible cracks/warping at the outlet

• Disconnect power; for gas dryers, also shut off gas supply
• Pull the dryer forward and detach the vent hose
• Remove mounting screws/clips, replace the collar, and reuse existing hardware
• Clear lint from ducting, reattach the vent hose securely, and verify strong airflow at the exterior vent

This dryer power cord connects an electric dryer to a 4-prong household outlet. Replace a worn or damaged cord to restore a safe, reliable power connection and help prevent intermittent power or overheating at the cord connection. What it does:

• Connects an electric dryer to a 4-prong receptacle for proper power and grounding
• Four-conductor design supports modern installation requirements
• Replaces cords with cracked insulation, loose prongs, or burned terminals

• 1 dryer power cord

• Disconnect power at the breaker before servicing
• Attach to the dryer terminal block per the appliance's wiring diagram and secure the strain relief

This replacement screw secures appliance components so panels, brackets, and assemblies stay tight and aligned. Replace stripped or missing hardware to eliminate rattles and keep your unit assembled safely and correctly.

• Fastens panels, brackets, or components to the appliance frame
• Restores a secure fit when the original screw is lost, stripped, or corroded
• Helps prevent vibration noise and movement during operation
• Supports proper alignment of trim and assemblies

• Disconnect power; for gas units, also shut off the gas supply
• Use the correct driver to avoid stripping the head; do not overtighten
• Inspect and address damaged mating threads, clips, or brackets before reinstalling
• Refer to your model's parts diagram to confirm location and quantity

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This control knob attaches to the appliance's control shaft so you can select settings with a solid, positive feel. Replace a cracked, stripped, or missing knob to restore smooth operation and a clean, finished look.

• Attaches to a switch or valve shaft to select temperatures, burner levels, or cycles
• Transfers your hand turn to the control shaft for accurate setting changes
• Common symptoms: cracked hub, spins without engaging, wobbly/loose, falls off, or missing
• Helps maintain a uniform appearance across the control panel

• Disconnect power (and shut off gas, if applicable) before servicing
• Pull the old knob straight off the shaft; avoid prying against the control panel
• Align the insert with the shaft's flats or splines and press straight on until fully seated
• Match position- and finish-specific knobs to the original on models that use different knobs per location

This front top panel lock secures the top to the front of the cabinet, keeping the panel closed and aligned. Replacing a worn or broken lock helps eliminate gaps and rattling for a solid, factory-tight fit.

• Holds the front edge of the top panel to the cabinet frame
• Maintains proper alignment to reduce panel movement and vibration
• Helps the top stay closed during operation
• Common symptoms: top won't stay down, visible gap at the front edge, rattling/squeaking from top area, broken or missing lock

• Disconnect power; for gas units, also shut off the gas supply
• Support the top/front panel before removing the old lock
• Remove fasteners or release tabs, note orientation, and transfer any reusable hardware
• Install the new lock and verify the top engages securely before reassembly and testing