Mim-D00a Parts

This is a wiring harness that connects the water pump to the electrical system in a commercial-style ice machine. It carries power and control signals to the pump, ensuring proper water circulation during ice production. Replace this harness if the pump fails to operate, runs intermittently, or if the wires show signs of damage, corrosion, or burnt connections.

This 15-inch door gasket is a direct-replacement sealing gasket that restores a tight door seal to the appliance, helping reduce heat and air leaks for more consistent temperature control and improved efficiency. What it does:

• Seals the door edge to prevent loss of heat, steam, or cooled air during operation.
• Helps maintain consistent internal temperature for proper cooking/drying/operation.
• Common symptoms it can fix: visible cracks, tears, flattening, gaps, or a door that does not close flush.
• Reduces stray heat or moisture around the appliance that can indicate a worn seal.

• Disconnect power (and gas if applicable) and allow the appliance to cool before servicing.
• Remove the old gasket carefully and inspect the sealing channel for debris or damage before installing the new gasket.
• Start installation at the top and press the gasket evenly into the channel, working around the door so the flange seats fully; replace any fasteners or clips as needed.
• Do not stretch, trim, or modify the gasket unless OEM instructions explicitly direct it; the appliance diagram for orientation.

Screw: 8-16 x 3/8 inch.

Size: 8-18 x 1/2 inch.

Size: 8 x 1-1/4 inch.

Ice machine not making ice or compressor not starting? This electronic control board manages freezing cycles and water pump operation. Moderate repair.

Ice maker not filling or dispensing ice? A faulty solenoid valve coil prevents proper water flow. This coil restores reliable valve operation in your unit.

If your ice maker pump won't run or stops draining, damaged wiring may be the cause. This pump wire harness restores electrical connection. DIY-friendly.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

Self-tapping screw for refrigerators. Secures handles, panels, and internal components. Replace missing, stripped, or damaged screws during repairs.

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

This spacer maintains the correct distance between mating components in your appliance's assembly so parts align and operate smoothly. Replacing a worn or missing spacer can correct looseness, rubbing, or vibration-related noise.

• Holds a precise gap between parts for proper alignment and motion
• Prevents metal-to-metal contact and premature wear
• Helps reduce vibration, rattling, and scraping noises
• Common signs include misalignment, unusual gaps, looseness, or rubbing in the related assembly

• Disconnect power (and shut off gas/water, if applicable) before servicing
• Refer to your model's diagram to locate the spacer's exact location and orientation
• Inspect related fasteners and bushings; replace if worn
• Do not overtighten hardware to avoid deforming the spacer

Small plastic cap that covers the drain fastener on your ice maker. Shields the screw and surrounding liner from moisture and debris. Replace when cracked or missing.

Replacement screw that secures panels, brackets, and trim to appliance cabinets. Restores reliable hold when original hardware is stripped or missing.

Fix ice maker clicking or not cooling issues with this compressor start relay. Restores normal compressor starts. Moderate DIY repair in under an hour.

Holds and secures the water filter in your ice maker, ensuring clean filtered water. Replace if cracked, leaking, or filter won't seal properly. Verify fit with your model number before ordering.