Mmv1175jz00 Parts

After extremely poor support from WhirlpooI and researching numerous U-Tube videos, I fully troubleshot potential failed components and connections. All appeared to function properly, so I reassembled the unit and experienced the same problem as before. I then narrowed down the problem to either the Touchpad ($57+$8 shipping) or the control board ($295+shipping). If those did not work, then a new Microwave of better quality, reliability and support than original microwave, Unfortunately,... Read more

Ordered mounting bracket but was surprised to find that the bracket model number had changed many times from the manufacter date of the microwave vent unit. Was hesitant if I was ordering the right part but I trusted the cross referencing of appliance parts pro and I got the exact bracket that I needed Read more

In order to get the bulb screw base out of the socket I had to remove the bottom metal panel and remove the the bulb base. Once I removed the socket, I noticed that the one of the electrical solderless connectors was corroded and burned. I replaced the connector, socket, and bulb. Works great now. Read more

Mom had slippery fingers and broke the microwave plate, luckily AppliancePartsPros.com had the exact same plate to replace it. They made it easy to find, order, and ship. Thanks for keeping life going without missing a step! Read more

It is difficult (if not impossible) to remove the electronic switches from the hard plastic latches. I replaced all three switches and both the upper and lower latches I also replaced the main 20 amp ceramic fuse which blew out when the latch/switches failed. Read more

Watched a You tube video, showed how to remove bottom, unhook wiring, then proceed to top case. Once removed, case is turned upside down so the capture nut can be installed. Part fit perfectly and BAM, done. Case refitted and finished. Part arrived in 2 days. Great service. Read more

I have used appliance parts pros before, their website is easy to use. I typed in the model and serial numbers, of course the number I have is rare, It did not show up on the list of models. It made me a little hesitant to submit the order. All three products came in the same box and on the same date it was promised. Just after opening the package I put everything in the microwave and I was relieved when everything fit perfectly. Read more

Very easy fix. Unplugged microwave, then lowered bottom panel, removed the two leads to the turntable motor, removed two screws attached to motor, removed old motor, put new spacer on motor stem, installed motor with same two screws, reattached the two wires, reattached panel ( after cleaning all the grease that built up over the last 6 years), plugged microwave in and good as new! Took me twenty minutes. Note: the two screws holding the motor were not Phillips like those holding the panel. So... Read more

Bought a new home with microwave venting into kitchen. Ordered damper assembly needed to vent through the wall to the outside. Removed microwave, followed directions in original installation instructions, turned fan over, cut hole in wall, installed wall cap and replaced oven. Problem solved. Read more

Replacing a magnetron in my particular 9-year-old microwave (a microwave/hood combination) was not a simple “plug & play” operation. That is why I am placing this in the slightly difficult area. First, it takes 2 people to remove the microwave from the top of the stove. Next the main outer panel need to be removed. After that, 2 sheet metal panels need to be removed in order to expose the high voltage components for testing. Always discharge the high voltage capacitor first before doing... Read more

My husband installed it. Read more

Obtained the replacement motor and tray coupler from Appliance Parts Pro. Video of the typical replacement was very helpful to show what to expect and how to replace the motor and coupler. The removal of the bottom plate was held in place by several phillips screws. The motor was attached with two torx screws. The electric connection clips to the motor required needle nose pliers to pull them off. The tray coupler was simple to install after the motor was secured and bottom plate was replaced.. Read more

With help from family we were able to install my microwave in just a short time. Read more

I ordered a new magnetron and a new capacitor and after they arrived I set to work. I took plenty of pictures with my phone to remind me how the components came apart but it was pretty straight forward. Once the new parts were in and everything was reassembled the microwave worked good as new. The repair was less than a third the cost of replacement and no special tools are required. Just be careful to discharge the capacitor. This website is a great resource. Read more

I replaced the upper and lower interlock switch assemblies. Read more