Mtb2156ge Parts

This speed clip is a small retainer that slides over a panel edge to provide a captive thread for a screw. Replacing a worn or missing clip restores a tight, rattle-free hold on the attached component. What it does:

• Slides over a panel or bracket to create a captive thread for a mounting screw
• Maintains tension to resist vibration and loosening
• Helps when a screw spins or won't tighten due to a missing retainer
• Addresses loose, rattling, or misaligned panels or trim

• 1 speed clip

• Disconnect power and, if applicable, shut off water before servicing
• Note the original clip's location and orientation for correct fit
• Fully seat the clip on the edge; start the screw by hand to avoid cross-threading
• Do not overtighten; ensure the component is secure and noise-free

This is the front rail for a pick-off style door shelf bin. Replacing a cracked or missing front restores the bin's ability to hold bottles and jars securely on the refrigerator door.

• Forms the front barrier of the pick-off door shelf/bin
• Snaps to the bin back to help keep items from sliding or falling out
• Typical symptoms: cracked plastic, broken locking tabs, loose or missing front panel
• Restores proper door storage and helps prevent spills

• Empty the bin and remove it from the door before replacing the front piece
• Allow plastic parts to warm to room temperature to reduce the chance of cracking
• Align the new front with the bin back and snap it into the locking tabs
• Confirm the front is fully seated before reloading the shelf

This freezer door gasket replaces a worn or deformed seal to restore a tight, even closure on the freezer door. A proper seal keeps cold air in and humid air out, reducing frost buildup and temperature swings.

• Creates an air-tight seal between the freezer door and cabinet to contain cold air
• Helps maintain correct temperature and efficiency; reduces frost/ice around the door perimeter
• Symptoms of failure: tears, cracks, warping, gaps, or door not closing fully
• Presents as frost buildup, moisture/condensation, or warm spots in the freezer

• Disconnect power to the refrigerator before servicing
• Let the new gasket relax (lay flat; warm gently with hot water or a hair dryer) for easier fit
• Remove the old gasket from the retainer/channel; on screw-retained styles, loosen (do not remove) liner screws as needed
• Seat the new gasket evenly, starting at the corners; use gentle heat to smooth wrinkles and ensure a uniform seal all around

This radiant-style defrost heater melts frost from the evaporator during automatic defrost cycles. Replacing a failed heater restores airflow and helps maintain consistent temperatures while preventing ice buildup on the freezer back wall.

• Heats the evaporator coil to clear frost/ice during the defrost cycle
• Promotes proper airflow for stable cooling performance
• Common fix for heavy frost on the back freezer panel, warming in the fresh food section, or a noisy evaporator fan contacting ice
• If the element tests open (no continuity), the unit will not defrost

• Disconnect power before servicing; allow built-up ice to melt for safe access
• Access from the freezer by removing the rear panel; handle the glass-sheathed element carefully
• Note wire routing and transfer any reusable shields, clips, or insulation from the original part if present
• After replacement, verify the defrost thermostat/sensor and control initiate a defrost cycle

This right-side rail supports and guides the refrigerator's meat/deli drawer for smooth, level operation. Replace a cracked or worn rail to restore proper drawer movement and prevent tipping or spills.

• Mounts on the right side to support and guide the meat/deli drawer
• Provides the track for smooth opening and closing
• Keeps the drawer aligned and level under normal load
• Common fix for jamming, wobbling, falling drawer, or visible rail damage

• Disconnect power; remove the meat/deli drawer (and its shelf, if needed) before replacement
• Confirm orientation: right-hand side when facing the refrigerator interior
• Align tabs and mounting points; fully seat the rail before reinstalling the drawer
• Reuse existing hardware; avoid overtightening screws into plastic

This replacement light bulb restores clear, reliable illumination so you can see contents and monitor appliance operation. Replace a burned-out, dim, or flickering bulb to bring visibility back to the area it lights. What it does:

• Provides illumination in the appliance's interior or designated lighting location
• Makes it easier to see contents and check status at a glance
• Common symptoms: light won't turn on, intermittent/flickering light, dim or blackened bulb

• 1 light bulb

• Disconnect power before servicing; allow hot surfaces and the old bulb to cool completely
• Remove any lens/cover, then remove the old bulb
• Install the new bulb securely without overtightening; reinstall the lens/cover if present
• Restore power and test operation

This defrost thermostat is the temperature limit switch for the evaporator. It lets the defrost heater run when coils are icy and opens as they warm to end the cycle, helping stop frost buildup and restore steady cooling.

• Monitors evaporator temperature; closed when cold to allow the defrost heater to energize
• Opens as the coil warms to terminate defrost and protect components from overheating
• Failure may cause heavy frost on the back wall/evaporator and weak airflow or a warm refrigerator section
• Can also lead to long run times or cooling that returns only briefly after a manual defrost

• Unplug the refrigerator or disconnect power before servicing
• Located behind the freezer's rear panel on the evaporator; remove shelves/ice bin and panel to access
• Reinstall in the same position/clip for firm contact with the coil or tubing
• Make secure, insulated wire connections and route wiring away from sharp edges and moving parts

Due to manufacturer changes this kit includes PTC start device, overload, electrical cover, jumper wire and instructions.

This lower hinge pin is the pivot shaft for your refrigerator door. Replacing a worn or bent pin restores smooth movement and proper alignment so the door seals and closes correctly while reducing hinge noise.

• Serves as the pivot point between the door and the lower hinge bracket
• Helps maintain door height and alignment for an even gasket seal
• Wear or damage can cause door sagging, rubbing, squeaking, or inconsistent closing
• Replacing the pin can restore smooth swing and reduce wobble at the hinge

• Disconnect power; remove items from the door. Support the door and remove the upper hinge to lift the door off the lower hinge.
• Replace the lower hinge pin on the hinge/bracket, reusing any model-specific washers or bushings.
• Reinstall, level, and align the door so the gasket seals evenly; verify smooth swing and positive closure.

The Dishwasher Rack Roller is an OEM part for Whirlpool dishwashers. It is designed to facilitate the smooth movement of the dishwasher rack in and out of the appliance. This roller ensures that loading and unloading dishes is easy and efficient, allowing the rack to glide effortlessly along the tracks.

Over time, dishwasher rack rollers can wear out or become damaged due to frequent use or accidental mishandling. Causes of a bad roller include general wear and tear, buildup of debris, or impact damage.

Symptoms of a bad roller include:

• Difficulty sliding the rack in or out
• The rack becoming stuck or jammed
• Uneven movement of the rack
• Excessive noise when moving the rack

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This grommet is a small protective seal used where a hose, tube, wire, or component passes through or mounts to the appliance cabinet. It cushions the connection and helps prevent leaks, vibration, and wear for reliable operation.

• Provides a snug barrier between parts and metal openings to protect hoses, tubes, and wiring
• Helps seal against moisture to reduce seepage
• Dampens vibration and rattling noises
• Replace if cracked, hardened, missing, or no longer stays seated; symptoms may include drips at a pass-through, buzzing/rattling, or a loose fit

• Disconnect power; shut off water supply if applicable
• Access the grommet location and note orientation/routing
• Remove the old grommet and clean the opening
• Press the new grommet fully into place; reassemble and test for leaks/noise

This white freezer door handle restores a secure, comfortable grip and refreshes the appliance's appearance. Replace a cracked, loose, or missing handle so the freezer door opens and closes smoothly again. What it does:

• Replaces a damaged, worn, or missing freezer door handle
• Restores proper grip and leverage for normal door operation
• Helps address loose or wobbly handle conditions
• Matches the original white finish for a clean, uniform look

• Wear gloves and protect the door surface to avoid scratches
• Support the handle while loosening/removing existing fasteners
• Reuse existing hardware as designed; start screws by hand and tighten just until snug
• Check alignment and security before returning the appliance to service

This light socket replaces a worn or heat-damaged lamp holder so your appliance light works reliably again. Its straight-connector design fits applications with in-line wiring, ensuring a secure electrical connection to the interior light bulb.

• Holds the light bulb and supplies power to it
• Restores interior illumination for better visibility
• Straight terminal orientation for housings requiring inline wiring clearance
• Typical signs of failure: light stays off with a good bulb, flickers, or shows heat damage at the socket

• Disconnect power at the breaker or unplug before servicing; allow the area to cool completely
• Remove any lens/cover; transfer wires one at a time to maintain correct connections
• Secure the socket with existing bracket/fasteners; do not overtighten
• Test light operation before reassembly and confirm the door switch activates the light

Ice stripper removes ice cubes from the ice maker mold so the dispenser or storage bin fills properly. Replacing a worn or broken stripper helps the ice maker eject cubes cleanly and reduces ice jams or stuck cubes. What it does:

• Pushes or guides harvested cubes out of the ice mold into the bin during the ice maker's harvest cycle.
• Prevents cubes from sticking in the mold; a damaged stripper can cause incomplete ejection or leftover ice in the mold.
• Works with the ice maker's ejector mechanism to maintain consistent cube release and storage.
• A faulty or broken stripper may lead to noisy operation, partial fills, or visible ice build-up in the mold.

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Remove the ice maker or access panel per the manufacturer's instructions to reach the stripper; keep small parts and screws organized.
• Inspect the ice mold and surrounding components for damage or ice build-up; clear ice before installing the new stripper.
• After installation, restore power and run a test harvest cycle to ensure proper cube ejection.

This replacement roller mounting screw secures the dryer drum roller or roller bracket to keep the drum aligned. Installing the correct screw restores proper roller position and helps reduce drum wobble and rubbing noises. What it does:

• Fastens the dryer drum roller or roller bracket to the dryer cabinet or shaft
• Keeps the roller aligned so the drum rotates smoothly
• Prevents the roller from shifting, which can cause scraping, squealing, or banging noises
• Helps avoid premature wear of the roller and drum seal caused by misalignment

• Disconnect power (and gas supply for gas models) before starting any repair
• Use appropriate hand tools; avoid power drivers that may strip the screw head
• Do not overtighten — snug to secure the roller without deforming the bracket or shaft
• Inspect the roller, shaft, and mounting hardware; replace any worn components for a lasting repair