Mvw5esxwo Parts

The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment. 

Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.

Symptoms of a bad clip include:

• Loose console assembly that is not securely fastened  
• Misaligned or dangling controls that do not sit flush
• Dislodged console at risk of detaching from housing
• Missing clip leaving an open mounting point

This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Motor-Drive is an OEM part for Whirlpool washing machines. It converts electrical energy into rotational motion to power the wash cycle. The motor transmits torque to the inner wash basket or tub through the drive system to clean clothes through agitation and spinning actions. Issues with the motor-drive can negatively impact the entire functionality of the washer.

Causes of failure can be wear and tear over time, damage from oversudsing or unbalanced loads, or exposure to moisture. Ensure your washer keeps running at its best with this OEM Whirlpool replacement part.

Symptoms of a bad Motor-Drive include:

• The washer failing to start or stopping mid-cycle
• Excessive noise or vibration coming from the motor area
• Slow or inefficient spinning
• Inability to advance through cycles

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

The Lid Lock Bezel (White) is an OEM replacement part for Whirlpool washers. The bezel provides an aesthetic covering for the lid lock mechanism located on top of the washer. 

Causes of a bad bezel can include normal wear and tear from repeated use of the washer lid over time. Scratches, cracks or splits in the plastic material are also possible from accidental impact or drops.

Symptoms of a bad bezel include:

• Cosmetic flaws like discoloration, scratches or cracks that diminish the appearance of the washer
• Looseness, rattling or misalignment of the bezel covering 
• Difficulty opening or closing the washer lid securely. 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

This leveling foot stabilizes and levels your appliance on uneven floors. It threads into the base so you can raise or lower a corner, reducing rocking and vibration for smoother, quieter operation and proper alignment.

• Provides precise height adjustment to level the cabinet
• Helps prevent wobble, walking, or rattling during use
• Supports stable operation and proper door alignment
• Replaces a missing, stripped, or damaged foot

• Disconnect power; shut off gas/water if applicable
• With help, carefully tilt or brace the appliance to access the foot
• Thread the new foot in by hand, then fine-adjust with a wrench until level and stable
• Ensure all feet contact the floor; recheck level after positioning

This is the washer's main electronic control board (ACU). It coordinates cycle timing and runs the motor, valves, and safety locks so your machine starts, advances, and finishes cycles consistently when the original control has failed. What it does:

• Directs wash, rinse, spin, and drain sequences based on cycle selection
• Regulates the drive motor, shift actuator, water inlet valves, and drain pump
• Monitors inputs from the lid lock and sensors to protect the machine and ensure proper operation
• Common failure symptoms: won't start or power up, cycle won't advance, fills but won't wash/spin, erratic or intermittent behavior

• One main control board assembly

• Disconnect power before servicing; use ESD protection and handle the board by the edges
• Photograph/label wire connectors; seat all plugs fully and secure any locking tabs
• Reinstall in the original mounting location; transfer any mounting clips or covers from the old board if applicable
• Some models require running a calibration or diagnostic cycle after replacement—follow the service manual

This WASHER  is an OEM part specifically designed for Whirlpool top-load washing machines. Tailored to fit seamlessly, this component ensures the efficient operation of the washer. It plays a crucial role in maintaining the stability and balance of the machine during the washing cycles.

A damaged or worn-out top-load washer can negatively impact the appliance's performance. Causes of a defective washer might include prolonged use, physical damage, or exposure to excessive weight or force, resulting in instability or imbalance during operation.

Symptoms of a bad WASHER may include:

• Excessive vibration or shaking during the wash cycle
• Difficulty in maintaining balance while spinning
• Noisy or erratic behavior during the operation

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: 5  Position Switch
 

The washer pulley Cover is an OEM replacement part for Whirlpool washing machines. It is a removable plastic shroud that houses the drive pulley and belt mechanism.

Causes of a bad pulley cover can include cracks or breaks from repeated opening and closing over time. Chemical or moisture exposure can also damage plastic through standard usage cycles. 

Symptoms of a failing pulley cover include:

• Inability to properly close or latch the cover  
• Leaks or debris entering the pulley compartment
• Interference with belt or pulley movement
• Loose fasteners or mounting points that cause misalignment

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, and Kenmore models.

Includes connector and both clamps.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Contains two, six foot long braided hoses with 90 degree ends.

4 - Position Switch