We use cookies and similar tools for site analytics and advertising. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This 1-1/8 in wire retaining ring locks into a groove to secure components in place. It helps prevent parts from sliding off a shaft or shifting out of position so assemblies stay aligned and operate reliably.
Based on recommendation to replace the clutch if clothes aren't spinning dry enough, I ordered a new clutch. Upon disassembly, I observed no Ring Wire/C-Clip and that the bearing appeared worn. Where did the clip go? Well, the bearing wore down such that it wore out the clip and bearing up to the sleeve of the shaft. Knocked out the old bearing, tapped in the new and was done. I disassembled the brake shoes but believe you can get the bearing in and out without doing so. Not a bad job, just... Read more
Fixes agitator that won't move or spins slowly. This upper agitator section restores proper wash action when teeth strip or wear. 10-minute repair.
I replaced the thrust washer , agitator and agitator dog assembly. The repair took about 10 mins after watching the repair video. All works fine. Mike C Read more
Adjustable leveling leg threads into the washer base to support and stabilize the unit. Replace if cracked, stripped, or missing to level cabinet.
Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
Fixes washer that won't spin or agitate, hums but doesn't run, or smells like burning. This drive motor powers drum rotation for wash and spin cycles.
Replaced drive hub , drive clutch kit , & drive motor Read more
Fix a washer agitator that won't move clothes due to stripped splines. This lower agitator base restores wash action in about 30 minutes.
Replaced the agittator Read more
Washer won't start or advance through cycles? A failed capacitor prevents proper motor startup. This part stores energy to boost the motor during operation.
I originally thought it to be my capacitor. But after installing the new one my machine still wouldn't wash, upon further inspection the hose that connects to the water level indicator on the control panel had popped a loose. I reconnected it and my washer is working just fine now. So try and do a complete inspection before spending unnecessary money ($125) like I did. Read more
This water inlet valve controls the flow of hot and cold water into the washing machine tub during fill cycles. It contains solenoid-operated ports that open and close in response to signals from the control board. Replace this valve if your washer is not filling with water, filling slowly, leaking from the back, or continuing to fill when it shouldn't.
Replaced water inlet valve Read more
Replacement power cord that connects your washer to the wall outlet. Includes strain relief for cable protection. Needed when original cord is damaged, pinched, shorted, or worn. Direct plug-in installation.
Bought a new cord and removed the back of the washer and unclipped the old and clipped in the new. 5 minutes tops. Read more
This factory screw secures panels, brackets, and other components in your appliance. Replace a missing, stripped, or corroded fastener to restore a tight fit and keep parts properly aligned and rattle-free.
In the past we’ve fixed the latch with just high speed great. This time we ordered a new latch and replaced it. Washing machine has been working perfectly ever since. It was very easy to find the right part by simply entering the model number of my washing machine. It was quick delivery and the correct part. Very happy to have a working washing machine again. Read more
Replaces the upper tub ring that mounts on top of the outer tub as a splash guard. Order a new ring if yours is cracked, broken, or no longer securely attached.
This was the second attempt at fixing this problem. The first repair and parts were generated by listing the problem and reviewing the potential corrections, listed on the web site. From making repairs on other clothes washers, I was confident that some of those potential causes could have been the cause. Unfortunately the counterbalance spring and suspension springs were not the cause as they were attached as intended and in good condition. I reached out for Appliance Parts Pros input... Read more
Secures the motor to its mounting point in your laundry center. Replace if the retainer is worn, broken, or has lost tension to prevent motor misalignment.
Replaced with new retainer clips and new capacitor to fix future problems Read more
Washer won't drain or clothes have residue? Replace the drain pump filter that screens debris and prevents clogs. Protects pump from damage.
On a 3 year old Maytag...........New gear case and hub installed. The videos produced by AppliancePartsPros are quite helpful, even though the video was not of the exact make and model number I was repairing, the similarities were so great that it may as well have been the same make and model number (whirlpool and Maytag essentially make the same thing and slap I different sticker on them) Read more
Fix washer water leaking into tub or slow dripping when off. Water inlet valve assembly replacement stops fill valve leaks. Easy DIY repair with video.
I ordered from this company expecting the parts to be later than they said and the parts showed up in 2 days like they said. Just before the Easter holiday even. Amazingly fast. Very satisfied!!! Washer is up and running again. Great job on getting me my parts! Thank you! Read more
This retainer ring is a genuine OEM replacement part sourced directly from the manufacturer for use on front load washing machines to hold the boot seal in place. The boot seal is the gasket that seals the washing machine when the door is closed to prevent water from leaking. The retainer ring is located flush against the boot seal and has either a spring clamp or screw clamp that secures it. Over time, this ring may become damaged due to the washing machine's normal use and age. If the ring is not tight, the washing machine could leak when in use. If water is coming from the door, it is a good idea to inspect and replace the retainer ring and possibly the boot as well.Unplug the washing machine to prevent electrocution. Remove the front panel, the detergent dispenser, and the kickplate to access the retainer ring. Locate the clamp on the ring and loosen it. Remove the retainer ring and set it to the side. Inspect the boot and then install the new retainer ring. Tighten the clamp and reassemble the washing machine. This retainer ring is sold as an individual unit. It is designed specifically for washing machines manufactured by Whirlpool.
Im not a repairman, so all my knowledge to fix my washer came from either youtube or online chats. I posted this to help the next dad trying to save a few bucks. Door sensor... Since door sensor worked correctly, verified that by starting washer with door open, and agitate cycle would not start until door was closed. Meaning door sensor worked correctly. Timer... In high spin cycle washer sounded correcltly spinning, but when opening door, drum was was not moving. So timer was triggering... Read more
Upper agitator not turning or engaging? This washer clothes mover works with cam and dogs to roll laundry. DIY repair in 15-30 minutes with video guide.
Opened lid during cycle and found upper agitator not turning.Removed dust cover seal and saw cam turning but dogs were only engaging once in a while.Although I didn't need to replace the upper agitator I did anyway,along with the agitator cam kit. I watched the quick repair video and repaired the washer myself in less than 30 min. Read more