We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
This is an electrically controlled water inlet valve that opens and closes to allow hot and cold water into the washing machine during the fill cycle. It is activated by the washer's control board or timer to regulate water flow at the correct times. Replace this valve if the washer is not filling with water, fills slowly, continues to fill when turned off, or leaks from the back of the machine near the hose connections.
I called AppliancePartsPros to find a replacement water inlet valve. They talked me through finding the clothes washer model number. Once the model number was located, the AppliancePartsPros person on the phone found the correct replacement valve. I received the valve 3-5 days after ordering. I downloaded the clothes washer repair manual and watched some YouTube videos regarding valve replacement. I followed the steps in the repair manual being careful to mark anything I had removed during... Read more
This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.
Took off cover, installed new parts. Read more
Agitator won't move or slips during wash? A worn drive shaft causes weak agitation. This shaft transfers motion from the gearcase to restore firm engagement.
I had to replace the drive shaft and the lower agitator. The motor coupling was also worn out. The repair was challenging because I had to rebuild the gear box. This step was really messy and I had to wait for the liquid gasket to set prior to completing the repair. Cleaning and prep of all of the parts tripled the repair time. Read more
Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.
Used for lid switch.
Researched this kenmore washer on-line and found the problem to be the lid switch. Saw a diagram on how to jump this switch by connecting a wire to both outside wires on the harness and voila! It worked! This is not a fix but it allowed me to finish the load of unwashed clothes and told me which part was bad (do not run washer jumped like this.......fire hazard!) Ordered the lid switch and it was an easy repair. A $14.00 switch was a lot cheaper than a $450.00 washer. Thanks appliance parts... Read more
Type AB #8-18 x 5/8 inch thread-forming screw secures panels and components in appliances. Replace missing, stripped, or corroded fasteners.
It was very easy to fix after watching your video.. Read more
Replace your washer's anti-rattle clip to eliminate vibration noise and buzzing during cycles. Secures components with light spring tension. Confirm fit with your model number before ordering.
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever. Read more
This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:
Two 5-foot nylon braided hoses connect household water supply to washer inlet valves. Replace cracked, leaking, or aging hoses to prevent water damage.
Watched u tube video. Ordered replacement water inlet valve and new hoses. Dismantled washer and replaced defective valve and installed new hoses. The repair went very easily and the washer worked perfectly as a result. Read more
Contains two, six foot long braided hoses with 90 degree ends.
I had a problem with the drain pump on my Kenmore HE3 and I replaced it using a drain pump I ordered from APP. That fixed that problem but once I started running the washer I started getting a FH error code. I looked it up and found that it was a problem with the washer not filling properly. I pulled the washer out and found that one of the fill hoses had kinked when I pushed the washer back in place. There was also some writing on the hose that read "Change hose every five years". I know I had... Read more
The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.
Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads.
Symptoms of a bad screw include:
This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Springs were broken and back bracket was bent I replaced the bracket and all four Springs including the vertical one. I removed the cabinet as shown in the video. Then with a pair of vise grips's removed the springs one by one and replace them. The bracket was rusted And bent i used a quarter inch socket with a quarter inch ratchet to remove the screw. Due to the rust i used penetrating oil the screw. Read more
Size: 10-16 x 5/8 inch.
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete. Read more
Noise filter (line filter) that suppresses electrical interference on the washer power line. Protects electronic controls from power surges and reduces EMI. Replace if washer has intermittent operation or won't start.
Popped the back control panel and checked where the power comes in. Had power. On the other side of that component there was no power. Found the problem. The hardest part was finding where they hid the model number. Up and under the back of the lid. Nice hiding place. Read more
Used from harness to top.
Fixing the problem was quite simple. First, I removed the lid assembly (thanks to the diagrams supplied by AppliancePartsPros.com!). Getting the back two screws out was very difficult because I couldn't see them from the front and I could not move the unit out of the enclosed space. After some trial and error, I located the screws which were 5/16 hex head screws and removed them with a MAGNETIC nut driver. (The magnet assures that the screw will not drop down into the mechanism). Second, I... Read more
Right hand side
New parts easy fix Read more
This is a small tube of silicone-based gasket sealer used to bond and seal gaskets during washer repairs. It creates a watertight seal between mating surfaces to prevent leaks around tub components or pump housings. Use this adhesive when replacing gaskets or resealing joints where the original sealant has deteriorated and water is leaking.