Nav8505aww Parts

• Shakes and moves

1.) Made sure BOTH Hot & Cold Water Lines turned off to Maytag Washer. (I have dual shut-off valve for those two water lines), 2.) Briefly ran Washer on Warm Water Setting, removing water pressure & remaining water from Hot & Cold water lines. 3.) Unplugged Washing Machine. 4.) Used Needle Nose Pliers to remove BOTH Hot & Cold Water hoses from the hookup on the back of the washer. 3.) Made sure I had an empty bucket, on hand, to catch remaining water that may come out of now-removed, hot &... Read more

I figured it had to be the flume; changed the flume and hose, mounting screws Read more

The machine would not run a full cycle before it cut off and had the code "FE" and water was too high. The water inlet valve needed to be replaced since it was letting in too much water at time. The repair was easy. Unplug machine and turn off cold water. Remove cold water line and drain water into bucket. Remove back two braces located at the top on each end of machine This will allow you to move top cove back about one inch. Pull back top cover about 1 inch then lift off cover. Remove... Read more

First; The part was ordered on Thursday and I received it on Friday! The kit was the correct one and complete with everything needed. (Maytag Atlantis MAV6200AWW – APV4373103 tub seal kit & bearing) Great Service ! I will certainly recommend you guys ! Some of the things I encountered installing the tub-seal on a machine that is 15 years old: Be prepared to do considerable cleaning of the tub cover, tub assy and outer tub. The 4 tub assy bolts were very rusted to the point the ½ inch socket... Read more

• Will not stop filling with water

Unplugged washer and called for a water truck to pump out basement, 2 feet of water. Read more

I replaced the worn parts. Removed the electric motor/pump assembly then took it to my motorcycle repair shop to clean/maintenance the motor, remove the old pump because it was stuck on the motor shaft. Once removed I blew out dust/debris from the motor w/compressed air. Sanded and filed the corrosion off the shaft, applied a "sealing grease" of sorts to the shaft to make potential future removal easier and reassembled. I took the whole wamma jamma home, reinstalled and wah-la, fixed. I am... Read more

I had a lot of problems removing the spin hub, I had to use an air impact wrench to un screw it even then it was very hard, it did not go easy with the hammer & pipe wrench as shown in the video. It was also very hard to remove the bottom spin bearing I had to cut the bearing retainer with a dremel tool so I could get my puller on it. After I struggled to get it apart The repair went very easy, I used brake spring pliers to remove the springs it worked like a charm. I am very pleased with... Read more

Replaced entire switch assembly Read more

I had a lot of problems removing the spin hub, I had to use an air impact wrench to un screw it even then it was very hard, it did not go easy with the hammer & pipe wrench as shown in the video. It was also very hard to remove the bottom spin bearing I had to cut the bearing retainer with a dremel tool so I could get my puller on it. After I struggled to get it apart The repair went very easy, I used brake spring pliers to remove the springs it worked like a charm. I am very pleased with... Read more

New timer. New water level switch. Works fine now. Read more

Unplugged dryer, took off back plate, unplugged wires from switch, turned and removed. replaced switch plugged wires in, put plate back on reinstalled knobs, plugged in. Read more

I replaced the friction ring, counter balance spring and all six of the tub rings. Though not a terribly difficult repair it was time consuming as the cabinet had to come completely off to access the rear of the tub. Once all of the springs were removed it was easy to slide the tub to the side, tip it and remove the old ring. Replacing it was just as easy. Replacing all the springs was made more difficult due to the additional tension the new springs had. I believe the total repair took me... Read more