Ntw6405ew0 Parts

• Lid or door won't close
• Won't start

Not wanting to spend hundreds of dollars on an appliance technician's service call, I searched online to troubleshoot the problems with my particular Maytag Washer Model Number MVWX500BW0. I stumbled across AppliancePartsPros.com and investigated there the most likely causes for my Maytag Washer's not agitating properly and not spinning at all. In order to acquire some additional information, I telephoned AppliancePartsPros.com and spoke with an extremely professional, knowledgeable and helpful... Read more

I found a YouTube video, order the parts about midnight Saturday and-they came in the mail before lunch on Tuesday. I laid the washer on the rear panel, removed both pulleys to clean them, installed the speed sensor. bolted the pulleys back in place, installed the new belt-making sure it was centered and everything moved freely, and attached the belt/pulleys cover. I set the washer back up, reattached the water lines, placed the drain tube, and plugged in back in. Works like new !!! 30 minutes... Read more

• Pumps but will not spin

This was my first attempt, ever, to repair a washing machine. After some internet research on the problems, I was able to determine that the shaft seal on the gearcase probably was leaking water into the gearcase with each use. No water was ever found on the floor, but when I turned the washer over to inspect the gearcase, I found a black, oily residue on the outside of it along with the same residue on the pulleys, the belt and the motor. I ordered a new gearcase, shift actuator, splutch... Read more

Replace belt. Read more

Installed new agitator Read more

I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more

Replaced all 4 rod and spring assemblies. Read more

Replaced all 4 rod and spring assemblies. Read more

GE Washer m/n GTW460ASJ6WW would allow other fill levels, but when set to "super" it would never stop filling. Checked water inlet valve (by initiating a fill and unplugging the unit) to see if the inlet valve was sticking open, that was not the issue. Decided to replace the board even though it is a significant fraction of the cost of a new washer. Local appliance stores didn't have the board but APP did, and of course, they are open 24/7 while my local part stores have decided the weekend is... Read more

• Leaking

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

• Will not stop filling with water
• No hot or cold water
• Will not fill with water

Replacing the water inlet valve fixed the problem. For many months we noticed cold water was just dribbling into the washer during the rinse cycle, and "warm" washes were hot not warm. It seemed like the cold water wasn't able to enter the machine. Then one day the cycle just stopped when it reached "rinse" and wouldn't go any further. I first tried solving it by cleaning the filter where the cold water hose enters the machine at the back. It was coated in sediment (the water comes from a... Read more

Replaced solenoid valve assembly. Easy repair. Read more

After looking up the model number of my washing machine on AppliancePartsPros.com I ordered the suspension rod kit, two sets of tub centering springs (one spring per corner), a Ring-Tub (mine was breaking apart due to banging around) and a spare suspension bearing kit in case I need it later. I spoke to a very helpful customer service rep on the phone just before placing my order. They have customer service representatives answering the phone late at night. I was surprised. All of my parts were... Read more

Remove one bolt in the center of the agitator need a long extension, couldn't be any easier. Read more

I ordered the parts, after assuring my diagnosis was correct from APP’s knowledgeable representative, and they were shipped quickly. I tipped the washer and disassembled the parts to be replaced and then installed a new clutch, clutch spring and mode shifter. Read more

• Shakes and moves
• Noisy
• Pumps but will not spin

Replaced washer drive block and Cam. I called around and finally settled on Appliance Parts Pros because they helped diagnose the problem, told me what parts to replace and had videos to show me how to do it. In completing the repair I had to remove quite a few pieces of hardware in order to get at the part I was to replace. The videos helped but there is a learning curve while you familiarize yourself with the parts and figure out how the remove them. Eventually I got to a large nut that,... Read more