Pbb911sj1ss Parts

Ordered and installed new ones. Read more

Ordered the new gasket from you - installed it and now my freezer is sealed i called to order the correct replacement and they were the very best at helping me !!!!! Read more

I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more

Touch up paint Read more

Replaced It With New One Read more

• Noisy

I pulled the refrigerator out, removed the back panel, disconnected the fan motor. I did not know how hard or easy it would be to remove the fan from the motor shaft so I removed the motor with the fan attached and then removed and replaced the fan. This would not be necessary if you have a lot of strength, but if you need leverage to push the fan down on the shaft you might want to disconnect and remove the motor fan assembly too. After replacing the motor assembly and reconnecting I tested by... Read more

• Freezer not defrosting
• Freezer too cold
• Fridge too warm
• Freezer section too warm

After we moved into our new home, we realized that the freezer was very cold and the fins were frosting over, and the refrigerator wasn't cold. We had to take it apart and manually defrost it about once every 8 to 10 days. After research online, we found Appliance Parts Pros videos, which clearly explained how to fix it ourselves, a savings of at least $1,000 or more, since a new one of this size would have been in the arena of $1,200 to $2000. We ordered the three most likely parts to be bad,... Read more

Took off the freezer door, took off the top hinge on the refrigerator door, replaced the handle, re-installed the top hinge and the freezer door. This is a two person job - one to remove the top hinge and replace the handle, while a second person holds the refrigerator door in place. Replacing the handle was easy. The most irritating part was figuring out what parts to order. The drawing of the refrigerator door (Drawing # 4) used to figure out what parts to order was not clear. I paid $8... Read more

• Not dispensing water
• Ice maker not making ice
• Leaking

I watched your how-to video. It explained the repair PERFECTLY. It was an easy repair and the video was very detailed. It took the guesswork out of the repair. I was done in 5 minutes. thanks for taking the time to post videos for your parts. I'll shop here again. Best Regards, Chad M Read more

I ordered parts and replaced them. Service was great and fast, plus original parts. Thanks Read more

Very easy.Just set right in Read more

I watched the video on how to replace the ice maker and the replaced it with zero problems. Excellent help in trouble shooting problem and installation video further assisted in ease of installation. Read more

I had verified that the water supply was healthy, so it was either the icemaker unit or the water valve. I replaced the icemake first, based on a the pareto showing it was the culprit for most other people, but it didn't help. That replacement was straightforward; the hardest part was reaching all the way back to unclip the wiring harness since I am too lazy to totally empty the bottom freezer and remove the door. So the next step was the water valve. The hardest part of this was pulling the... Read more

Replaced the gasket . Parts were were here one day after ordered . U-tube video was a big help. Went faster and easier than expected . Read more

Had to take the back cover off. It was very tight to remove the fan that sat in the drip pan but did get it off, was able to apply the same level of cursing and got the new pan installed, installing the drain tube was a breeze. Found the parts price very reasonable. Hoping the Whirlpool redesigned the pan so I won't have to do it ever again. I was surprised at how bad the quality of their original part was. Probably saved myself $150.00 on buying the part and doing it myself Read more

Replaced the ice level arm Read more